Question about 1999 Isuzu Rodeo

Open Question

Installing thermostat ..is the Thermostat all the way down on top of the Block? Do I have to remove the Intake Manifold to install a new thermostat?

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
stevenhurc
  • 450 Answers

SOURCE: I need to replace the thermostat for my 2000 Isuzu

remove fuel pump fuse and start car when it dies try to start again, no more spluttering just cranking, the fuel system is now depressurised. you can now disconnect both of the quick disconnect fuel lines at rear lower section of inlet manifold this is hard to get to some access this by removing the EGR valve so you can get your arms down there watch out for sharp edges of manifold. you dont need to take the top section of the inlet manifold off but will need new lower inlet manifold gaskets to haed.once manifold is off block all intake ports with rag or put tape over ports to stop dirt and stuff falling into ports while continuing to work on the coolant pipes below to get to thermostat.undo only 4 long centre bolts and the 4 nuts, one in each corner(no.3 in picture).

stevenhurc_7.jpgyou dont need to remove throttle body but some people do.

Posted on Feb 24, 2011

Ad
  • 14036 Answers

SOURCE: I need to replace a

you need follow hose goes to cylinder block.the other hose goes to water pump which is the thing with the pulley.

Posted on May 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the thermostat in my 95 Isuzu rodeo 3.2 ltr. V6


where is such a simple word
where;
3.2L V6, SOHC head 6VD1 (not the 6vd1w twin cam heads)
x marks the spot
asked many time here, and same answer.
if you look , you see it, then see its not possible to get to the 2 rear bolts (telling you what?)
pull engine block, ? no
pull intake, yes.

here-bp54dlzlp0pmj5fwzd335nwr-4-0.jpg

Mar 07, 2017 | Isuzu Rodeo Cars & Trucks

1 Answer

Where is the thermostat mounted?


    • 1. Locate the thermostat housing by following the radiator hose from the radiator to the engine block. The metal cover that the hose attaches to is the Tahoe's thermostat housing.

    • 2

      Remove the radiator hose retention clip by manually squeezing the clip tabs together. With the tabs together, pull the hose off the thermostat housing. Drain the fluid from the hose by holding the hose in the air. The fluid will drain back into the radiator.

    • 3

      Remove the thermostat housing by taking off the two bolts with a boxed wrench. Lift the hosing off the engine to expose the thermostat.

    • 4

      Pull the old thermostat out of the Tahoe's intake manifold. Place the new one into the intake manifold with the spring-loaded end inside of the intake.

    • 5

      Replace the old thermostat gasket with a new one. The gasket must remain dry during the installation process.

    • 6

      Place the thermostat housing on top of the thermostat gasket and bolt it into place.

    • 7

      Squeeze the radiator hose retention clip tabs together and slide the hose back onto the thermostat housing. Let go of the tabs to secure the hose into place.

Sponsored Links

Read more: http://www.ehow.com/how_6395786_change-thermostat-2003-tahoe.html#ixzz30u7ZzxV6

Mar 23, 2014 | 2000 Chevrolet Tahoe

1 Answer

Bad theromostat 3.2 isuzu how to


The thermostat on the 2001 Isuzu Rodeo 3.2L v6 is located on the top of the engine under the upper intake manifold. In order to replace it you will have to depressurize the fuel system by running the engine with the fuel pump fuze removed until the engine dies and then carefully remove the fuel rail and injectors. Then remove the intake manifold which will give you access to the coolant nozzle fixture attached to the top of the engine. The thermostat is in the top of the engine block under the nozzle fixture. Be sure to replace the thermostat with the proper replacement part (may be difficult to find) and put on new gaskets for the intake manifold before replacing it.

Apr 11, 2013 | 2001 Isuzu Rodeo

1 Answer

Where is the thermostat located in the 06 stratus


  • Find the location where the upper radiator hose connects to the intake manifold of the engine by tracing it from the radiator to thermostat intake housing bolted to the intake.
  • 2 Remove the radiator hose from the thermostat intake housing by loosening the band clamp that secures it into place. With the clamp loosened, pull the hose off the housing.
  • 3 Remove the two bolts that secure the housing to the intake manifold and then lift the housing off the intake.
  • 4 Lift the thermostat out of the intake manifold and place the new thermostat into the hole. The end of the thermostat with the pin protruding from it sticks out of the intake manifold.
  • 5 Lift the thermostat intake housing gasket off the intake manifold and place the new one onto the intake manifold.
  • 6 Place the thermostat intake housing onto the intake manifold and bolt it into place. Reconnect the hose using the band clamp.
  • Six-Cylinder Engines
  • 1 Drive the Dodge onto a set of front-end ramps and secure the parking break. Allow adequate time for the radiator fluid to cool down. Thirty minutes is usually adequate.
  • 2 Loosen the petcock on the lower right hand side of the radiator and drain all of the radiator fluid into a drain pan. Close the petcock once drained.
  • 3 Trace the lower radiator hose to the location where the hose connects to the engine block. The metal housing the hose connects to is the lower thermostat outlet. Remove the hose from the outlet by loosening the band clamp and then by pulling the hose off the outlet. Be careful--some fluid will drain from the hose.
  • 4 Remove the two bolts that secure the thermostat outlet to the engine block and pull the thermostat outlet off the block.
  • 5 Discard the O-ring inside the bottom edge of the thermostat outlet and place a new one into the outlet.
  • 6 Pull the thermostat out of the engine block and replace it with a new one. The end with the pin protruding from it sticks out of the engine block.
  • 7 Place the thermostat outlet onto the engine block and secure it into place. Reattach the lower radiator hose with the band clamp.
  • 8 Open the radiator filler cap located on top of the radiator and fill the radiator with the fluid previously drained from the system.


  • please dont forget to give good rateing thank you

    Dec 28, 2010 | 2006 Dodge Stratus

    1 Answer

    Change thermostat


    Typically, the thermostat is located under an aluminum fitting where the top radiator hose meets with the engine block or the intake manifold. You need to drain the antifreeze into a container from a valve at the bottom of the radiator so that the level is below the top of the engine block. Save this for reuse or disposal. Then loosen the hose clamp and remove the top hose from where it meets the engine block or manifold. Now, loosen the two or three bolts that hold the aluminum fitting from the engine block or manifold and remove it, revealing the thermostat.

    Pay attention to the orientation of the thermostat. Now, clean up the mating surfaces of the fitting and the manifold. Reinstall using a new thermostat orientated the right way, a new gasket and/or silicone sealer, and then the fitting. Attach the hose, refill the radiator, and test for leaks.

    Nov 25, 2010 | 2004 Chevrolet TrailBlazer

    1 Answer

    I need to change the thermostat


    REMOVAL
    1. Remove upper intake manifold.
    2. Partially drain cooling system below the thermostat level.
    3. Remove upper radiator hose from outlet connector.
    4. Remove coolant recovery system hose from outlet connector.
    5. Remove coolant outlet connector bolts.
    6. Remove thermostat assembly, and clean sealing surfaces.
    INSTALLATION

    25a9b05.gif
    1. Place the new thermostat assembly into the coolant outlet connector, aligning air bleed with the location notch on outlet connector.
    2. Install coolant outlet connector with thermostat in position onto thermostat housing. Tighten bolts to 12.5 Nm (110 inch lbs.).
    3. Install upper radiator hose.
    4. Connect the coolant recovery system hose.
    5. Install upper intake manifold.
    6. Fill cooling system.
    7. see thermostat mounting are below
    a4322e5.gif

    Oct 19, 2010 | 2002 Chrysler PT Cruiser

    1 Answer

    Location of thermostat on 2002 olds alero 2.2


    Thermostat Removal & Installation 2.2L Engine To Remove:
    1. Remove the exhaust manifold. If equipped with an automatic transmission.
    2. Drain the cooling system.
    3. Remove or disconnect the following: chevy_cav_02-04_tstat.gif

      • Thermostat housing to water pump feed pipe bolts. chevy_cav_02-04_feedpipe.gif

      • Thermostat housing to water pump feed pipe.
      • Thermostat.
    To Install:
    1. Install or connect the following:
      • Thermostat.
      • Thermostat housing to water pump feed pipe.
      • Thermostat housing to water pump feed pipe bolt.
        1. Tighten bolt to 89 in lbs (10 Nm).
      • Exhaust manifold if equipped with an automatic transmission.
    2. Fill the cooling system.
    2.4L Engine To Remove:
    Thermostat assembly 2.4L 87953024.gif

    1. Drain the cooling system.
    2. Remove the exhaust manifold heat shield.
    3. Remove the coolant inlet housing mounting bolts through the exhaust manifold.
    4. Raise and safely support the vehicle.
    5. Remove the coolant inlet housing stud from the oil pan.
    6. Remove wheel and tire assembly.
    7. Remove the engine splash shield.
    8. Remove the mounting bolts from the transaxle-to-engine block support. Remove the support.
    9. Remove the coolant housing pipe.
    10. Remove the thermostat.
    11. Clean the mating surfaces.
    To Install:
    1. Install the thermostat.
    2. Install the coolant housing pipe.
    3. Install and secure the transaxle support-to-engine block mounting bolts.
    4. Install the engine splash shield.
    5. Install the wheel and tire assembly.
    6. Install the coolant inlet housing stud to the oil pan.
      • Tighten to 19 ft lb (26 Nm).
    7. Lower the vehicle.
    8. Install the coolant inlet housing bolts through the exhaust manifold.
      • Tighten the coolant inlet housing bolts to 10 ft lb (14 Nm).
    9. Install the exhaust manifold heat shield.
    10. Fill the cooling system.
    11. Inspect the system for leaks.
    3.4L Engine To Remove:
    1. Drain the cooling system.
    2. Remove the air cleaner.
    3. Remove exhaust crossover pipe.
    4. Disconnect the surge tank line fitting from the coolant outlet.
    5. Remove the thermostat housing to intake manifold bolts.
    6. Remove the thermostat housing outlet and thermostat.
    To Install:
    1. Install the thermostat and housing outlet.
    2. Install the thermostat housing bolts.
      • Tighten the thermostat housing bolts to 18 ft lb (25 Nm).
    3. Install exhaust crossover pipe.
    4. Connect the surge tank line fitting to the coolant outlet.
      • Tighten the fittings to 15 ft lb (21 Nm).
    5. Install the air cleaner.
    6. Fill the cooling system.
    7. Inspect the system for leaks
    prev.gif next.gif

    Oct 14, 2010 | Oldsmobile Alero Cars & Trucks

    2 Answers

    How to replace a themostat on a 2004 Gmc Envoy


    Please see my tip at http://www.fixya.com/cars/r5929960-s_thermostat .

    Specific instructions for your car are as follows. Let me know if you get stuck or have more questions.


    Removal & Installation


    4.2L Engine

    1. Remove the necessary coolant from the radiator.
    2. Remove the alternator, as outlined in the Engine Electrical Section.
    3. Loosen the outlet hose clamp at the thermostat housing. Remove the outlet hose from the thermostat housing.
    4. Remove the thermostat housing bolts.
    5. Remove the thermostat housing from the engine block.
    6. Clean all of the surfaces of the thermostat housing.
    7. Clean the sealing surface of the engine block.
    To install:
    1. Install the thermostat housing to the engine block.
    2. Install the thermostat housing bolts and tighten to 89 inch lbs. (10 Nm).
    3. Lubricate the inner diameter of the radiator hose with engine coolant.
    4. Install the outlet hose to the thermostat housing. Secure the hose with the clamp.
    5. Install the alternator.
    6. Fill the cooling system with specified coolant and concentration.
    7. Inspect all sealing surfaces for leaks after starting the engine.

    5.3L Engine
    NOTE The thermostat is not serviceable separately. The water pump inlet and thermostat must be replaced as an assembly.


    1. Drain the cooling system to a level below the thermostat.
    2. Remove the radiator outlet hose.
    3. Remove the water pump inlet bolts.
    4. Remove the water pump inlet and thermostat from the water pump.

    To install:
    1. Install the thermostat and thermostat housing to the water pump.
    2. Install the thermostat housing bolts. Tighten the bolts to 11 ft. lbs. (15 Nm).
    3. Install the radiator outlet hose.
    4. Properly fill the engine cooling system and check for leaks.

    Oct 08, 2010 | 2004 GMC Envoy

    1 Answer

    How do I install a new thermostat?


    Explorer Thermostat LocationHere is advice for finding the thermostat:

    • Follow the upper radiator hose from the radiator to the engine and there is a housing that houses the thermostat. Take it off and when you reinstall the thermostsat, make sure the spring goes toward the engine.

    • The thermostat is located on the motor block under the three bolt flang that the top rediator hose connects to. Remove the three 10MM bolts and the thermostat can be removed for replacement.

    How to Change an Explorer Thermostat
    • 1. Remove the air cleaner air duct from the throttle body and air cleaner.
    • 2. Follow the upper radiator hose to the engine to locate the thermostat housing. The housing is located at the front of the intake manifold.
    • 3. Loosen the hose clamp, then detach the hose from the fitting. This can be difficult. If it's stuck, grasp with a pair of adjustable pliers and twist to break the seal. Then pull it off.
    • 4. Remove the bolts and detach the housing cover. Be prepared some coolant may leak out as the gasket seal is broken. Remove the thermostat.
    • 5. Install the new o-ring onto the thermostat (no gasket is needed) and install the thermostat into the intake manifold with the spring side pointing toward the engine.
    • 6. Make sure the air release valve is in the up 12 o'clock position. Install housing cover and bolts. Reattach the hose fitting and tighten the hose clamp. Fill the cooling system with a 50/50 mix of coolant and water, and burp the system.

    Nov 05, 2009 | 2001 Ford Explorer Sport

    1 Answer

    Hot do you take off a 98 GMC 5.7 vortec intake


    Note, removing the upper intake manifold is not necessary when removing lower intake manifold, they are removed as an assembly.
    Disconnect negative battery cable. Drain cooling system. Remove air cleaner assembly and inlet duct. Mark and remove distributor. Remove upper radiator hose at thermostat housing. Disconnect accelerator and cruise control cables. Remove heater hoses from intake manifold. Remove EGR pipe.
    Disconnect fuel lines at rear of engine. Remove AC compressor and set aside(leave hoses connected). Remove canister purge solenoid. Disconnect theSCPI injector, ignition coil, Ignition Control Module, generator,IAC motor, TP sensor, O2 sensor, Exhaust Gas Recirculation valve and Engine Coolant Temperature sensor wiring harness connectors. Remove PCV valve and hose. Remove lower intake manifold bolts. Remove lower intake manifold.
    Installation.
    Always use New O-rings when reconnecting fuel lines at rear of engine. Apply a bead of RTV silicone sealer along the front and rear sealing surfaces of the block.See Fig.6. Install new gaskets and intake manifold on block while RTV is still wet to the touch. Use Threadlock 12345382 or equivalent to lower intake manifold bolts. Tighten lower intake manifold bolts in sequence to specification table. See fig. 7. To complete installation, reverse removal procedure.f52665d.gifabc2b5f.gif

    Oct 10, 2009 | 1998 GMC Sierra

    Not finding what you are looking for?
    1999 Isuzu Rodeo Logo

    Related Topics:

    124 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Isuzu Experts

    yadayada
    yadayada

    Level 3 Expert

    76649 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14380 Answers

    Are you an Isuzu Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...