Question about 2003 Kia Sedona

Open Question

P0338 already replace sensor possible airgap problem?

What is the proper procedure for replacing crank and or cam sensor 2005 sedona 3.5l....

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 2005 kia sedona ECU replacement

It's located at the passenger side behind the air conditioner plastic duct (inner firewall)

Posted on Sep 24, 2008

  • 701 Answers

SOURCE: where is the crank position sensor located in 2005

Hello martinezmelm: My name is Roger and I can answer your question. To locate the crankshaft position sensor. You will need to remove the timing cover. You will find the sensor on top of the crankshaft gear. Between the V of the timing belt.
Should you need further help please just ask. Please rate the answer as this way I know it was helpful. Thank You for using Fix Ya. Roger

Posted on Oct 19, 2009

  • 1 Answer

SOURCE: Crankshaft position sensor replacement on 2005 Kia Sedona

The CPS is located under the timming cover 4 small bolts remove the cover and the sensor is viewable 2 bolts have to be loosend and the wire leads up to a dual connector on the left side of the engine

Posted on May 18, 2010

  • 1 Answer

SOURCE: 2004 Kia Optima no start after timing belt, crank, cam sensor replacement

If your crank shaft sensor and timing belt went on your car and it died as a result of this then you might have bigger problems than no spark and no fuel. If what you said about your compression test is true then you might have one or more bent valves. This type of engine is what is known as an "interference engine" the loss of timing will throw off the valves causing them to be open when the piston is on the upstroke striking the piston head. Damaged valves will cost a bundle to fix....more than the car is worth probably. I have a 2003 KIA and had the same thing happen, fortunately after i fixed the belt and sensor it started up without the damaged valves. It is very much a game of chance it may have damaged them and it may not have. But if your valves are open on the upstroke and are bent it will force your fuel/air mixture out of the combustion chamber and even if you do have spark at the right time there will be no mixture to detonate. With all the problems I have been suffering through with my KIA I would suggest sending it on to car heaven, these cars have nothing but problems.

Posted on Sep 06, 2010

  • 5 Answers

SOURCE: how to replace crank position sensor on a 2004 Kia

have wife diagnose problem from her laptop while I am on the way to see if I can fix it.......take van to Parts America and have them run code then order part and listen to wife say how good she is!

Posted on Jan 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3.6vvt not starting


Hi there:

P0016 - Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)
The crankshaft position sensor (CKP) and Camshaft position sensor (CMP) work in harmony to control the spark/fuel delivery and timing. They both consist of a reluctor, or tone, ring which passes over a magnetic sensor, which generates a voltage, indicating position.



The crankshaft sensor is part of the primary ignition system and functions as the "trigger". It detects the position of the crankshaft relays that information on to the PCM or the ignition module (depending on the vehicle) to control spark timing. The Camshaft position sensor detects the position of the camshafts and relays the information to the PCM. The PCM uses the CMP signal to identify the beginning of the injector sequence. What ties these two shafts and their sensors together is the timing belt or chain. The cam and crank should be precisely timed together. If the PCM detects that the Crank and Cam signals are out of time by a specific number of degrees, this P0016 code will set.



Causes may include:
Timing chain stretched, or timing belt skipped a tooth due to wear
Misalignment of timing belt/chain
Tone ring on crankshaft slipped/broken
Tone ring on camshaft slipped/broken
Bad crank sensor
Bad cam sensor
Damaged wiring to crank/cam sensor
Timing belt/chain tensioner damaged

Possible Solutions: First, visually inspect the cam and crank sensors and their harnesses for damage. If you notice broken/frayed wires, repair and recheck.
If you have access to a scope, check the cam and crank patterns. If a pattern is missing, suspect a bad sensor or a slipping tone ring. Remove the cam gear and the crankshaft harmonic balancer and inspect the tone rings for proper alignment and make sure they're not loose or damaged or that they haven't sheared the key that aligns them. If they are properly installed, replace the sensor.
If the signal appears normal, then check the timing chain/belt for proper alignment. If it's misaligned, check for a damaged tensioner that may have allowed the chain/belt to slip a tooth or several teeth. Also check that the belt/chain isn't stretched. Repair and recheck.

Other crank sensor codes include P0017, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.


Additionally, in THIS LINK can find description and test about this fault.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jul 31, 2012 | Cars & Trucks

1 Answer

2005 Kia sedona over heated motor died ,cranks and turns over but will not start .whats the problem ?


What's the problem??? I think you pretty much explained it yourself...the engine has been overheated! You most likely have damaged cylinder heads and/or cylinder block, pistons, crank shaft, cam shaft, etc.. I would recommend having it checked by a professional to see if it is even worth repairing or if the engine must be replaced.

May 04, 2012 | 2005 Kia Sedona

1 Answer

I replaced the camshaft position sensor P0340, now the OBD is reading a PO0016


Causes that bring up code P0016 may include:
  • Timing chain stretched, or timing belt skipped a tooth due to wear
  • Misalignment of timing belt/chain
  • Tone ring on crankshaft slipped/broken
  • Tone ring on camshaft slipped/broken
  • Bad crank sensor
  • Bad cam sensor
  • Damaged wiring to crank/cam sensor
  • Timing belt/chain tensioner damaged
  1. First, visually inspect the cam and crank sensors and their harnesses for damage. If you notice broken/frayed wires, repair and recheck.
  2. If you have access to a scope, check the cam and crank patterns. If a pattern is missing, suspect a bad sensor or a slipping tone ring. Remove the cam gear and the crankshaft harmonic balancer and inspect the tone rings for proper alignment and make sure they're not loose or damaged or that they haven't sheared the key that aligns them. If they are properly installed, replace the sensor.
  3. If the signal appears normal, then check the timing chain/belt for proper alignment. If it's misaligned, check for a damaged tensioner that may have allowed the chain/belt to slip a tooth or several teeth. Also check that the belt/chain isn't stretched. Repair and recheck.
Hope this helps

Feb 06, 2012 | 2005 Chrysler PT Cruiser

1 Answer

We replaced the Water pump and Timing belt on a 1999 Plymouth Neon 2.0 Single Overhead Cam Engine. Engine Cranks, Is getting Fuel...but no spark. We changed the Coil Pack. It still cranks, but no...


If its not getting spark the choices are limited. You already replaced the coil pack so whats left is ignition module, crank sensor, knock sensor, cam sensor, or the timing was not was not set properly when putting it back together. Any one of those would create a no spark situation.

Mar 17, 2011 | 1999 Plymouth Neon

1 Answer

Where is the crankshaft position/crank angle sensor located on a 2005 kia sedona


Hi, at the front of the crankshaft. if its near time for the timing belt, you want to replace it along with any pullies, tensioner and water pump


The crankshaft position sensor is mounted on the engine near the crankshaft.

Operation

The crankshaft position sensor is a Hall-Effect sensor that senses the crank angle (piston position) of each cylinder and converts it into a pulse signal. The signal from the sensor is relayed to the ECM to indicate engine rpm and the position of the crankshaft.

Removal & Installation

  1. Disconnect the negative battery cable.
  2. Disconnect the connector from the sensor.
  3. Remove the bolt that retains the sensor in place.
  4. Remove the sensor from its mounting. To install:
    1. Installation is the reverse of the removal procedure.
    2. Clearance between the sensor and the sensor wheel should be 0.020-0.059 inch. 2002-2005
      1. Properly connect the scan tool.
      2. Start the engine and allow it to idle.
      3. Be sure the idle position switch is ON.
      4. Specifications are as follows:

        Temperature - 4°F, test specification 1500-1700 RPM Temperature 32°F, test specification 1350-1550 RPM Temperature 68°F, test specification 1200-1400 RPMTemperature 104°F, test specification 1000-1200 RPM Temperature 176°F, test specification 650-850 RPM

Mar 16, 2011 | 2003 Kia Sedona

1 Answer

Erreur p0016 on sienna 2003 after change t-belt


The crankshaft position sensor (CKP) and Camshaft position sensor (CMP) work in harmony to control the spark/fuel delivery and timing. They both consist of a reluctor, or tone, ring which passes over a magnetic sensor, which generates a voltage, indicating position.

The crankshaft sensor is part of the primary ignition system and functions as the "trigger". It detects the position of the crankshaft relays that information on to the PCM or the ignition module (depending on the vehicle) to control spark timing. The Camshaft position sensor detects the position of the camshafts and relays the information to the PCM. The PCM uses the CMP signal to identify the beginning of the injector sequence. What ties these two shafts and their sensors together is the timing belt or chain. The cam and crank should be precisely timed together. If the PCM detects that the Crank and Cam signals are out of time by a specific number of degrees, this P0016 code will set.

Symptoms of a P0016 will or may include:
* Malfunction Indicator Lamp (MIL) illumination
* The engine may run but with reduced performance
* The engine may crank but not start
* The engine may exhibit a rattle near the harmonic balancer indicating the tone ring is damaged
* The engine may start and run, but poorly

Causes may include:
* Timing chain stretched, or timing belt skipped a tooth due to wear
* Misalignment of timing belt/chain
* Tone ring on crankshaft slipped/broken
* Tone ring on camshaft slipped/broken
* Bad crank sensor
* Bad cam sensor
* Damaged wiring to crank/cam sensor
* Timing belt/chain tensioner damaged

Possible Solutions:
1. First, visually inspect the cam and crank sensors and their harnesses for damage. If you notice broken/frayed wires, repair and recheck.
2. If you have access to a scope, check the cam and crank patterns. If a pattern is missing, suspect a bad sensor or a slipping tone ring. Remove the cam gear and the crankshaft harmonic balancer and inspect the tone rings for proper alignment and make sure they're not loose or damaged or that they haven't sheared the key that aligns them. If they are properly installed, replace the sensor.
3. If the signal appears normal, then check the timing chain/belt for proper alignment. If it's misaligned, check for a damaged tensioner that may have allowed the chain/belt to slip a tooth or several teeth. Also check that the belt/chain isn't stretched. Repair and recheck.

Other crank sensor codes include P0017, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.

Hope helps.

Dec 20, 2010 | 2003 Toyota Sienna

1 Answer

3.6 in a 2006 pontiac g6 is throwing code p0017 is this crank sensors or what is the most common fix


P0017 - Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)

The crankshaft position sensor (CKP) and Camshaft position sensor (CMP) work in harmony to control the spark/fuel delivery and timing. They both consist of a reluctor, or tone, ring which passes over a magnetic sensor, which generates a voltage, indicating position.

The crankshaft sensor is part of the primary ignition system and functions as the "trigger". It detects the position of the crankshaft relays that information on to the PCM or the ignition module (depending on the vehicle) to control spark timing. The Camshaft position sensor detects the position of the camshafts and relays the information to the PCM. The PCM uses the CMP signal to identify the beginning of the injector sequence. What ties these two shafts and their sensors together is the timing belt or chain. The cam and crank should be precisely timed together. If the PCM detects that the Crank and Cam signals are out of time by a specific number of degrees, this P0017 code will set.

Symptoms of a P0017 will or may include:
* Malfunction Indicator Lamp (MIL) illumination
* The engine may run but with reduced performance
* The engine may crank but not start
* The engine may exhibit a rattle near the harmonic balancer indicating the tone ring is damaged
* The engine may start and run, but poorly

Causes may include:
* Timing chain stretched, or timing belt skipped a tooth due to wear
* Misalignment of timing belt/chain
* Tone ring on crankshaft slipped/broken
* Tone ring on camshaft slipped/broken
* Bad crank sensor
* Bad cam sensor
* Damaged wiring to crank/cam sensor
* Timing belt/chain tensioner damaged

Possible Solutions:
1. First, visually inspect the cam and crank sensors and their harnesses for damage. If you notice broken/frayed wires, repair and recheck.
2. If you have access to a scope, check the cam and crank patterns. If a pattern is missing, suspect a bad sensor or a slipping tone ring. Remove the cam gear and the crankshaft harmonic balancer and inspect the tone rings for proper alignment and make sure they're not loose or damaged or that they haven't sheared the key that aligns them. If they are properly installed, replace the sensor.
3. If the signal appears normal, then check the timing chain/belt for proper alignment. If it's misaligned, check for a damaged tensioner that may have allowed the chain/belt to slip a tooth or several teeth. Also check that the belt/chain isn't stretched. Repair and recheck.

Other crank sensor codes include P0016, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.


Hope this helps (remember to rate and comment this answer).

Nov 23, 2010 | 2006 Pontiac G6

Not finding what you are looking for?
2003 Kia Sedona Logo

Related Topics:

323 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...