Question about 2003 GMC Yukon

1 Answer

4wd is not turning on. its electronic 4wd and i push the buttons and it wont turn on

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I have a 2004 Yukon and today I got no lights and a check 4WD anouncement. I need help too. If I fix mine I'll let you know what I did.
henderland@sbcglobal.net

Posted on Apr 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 56 plate jimny the fourwheel drive light is on on the dash is it stuck in fourwheel drive ?


Did you reverse more than 10 metres? Sounds like the hubs are locked into 4wd.this will work if you have auto hubs.but sometimes you have to turn the hub manually if they don't disengage.if you have gone some time or distance in 4wd

Dec 08, 2014 | 2006 Suzuki Jimny 1.5

1 Answer

4wd auto shift does not engage 4wd.


for 4wl need to be stopped and put in neutral or park it wont actuate while driving [ blinking light indicates failure to engage ] 4wd hi can do while driving --if fails also then check and test for actuator sticking --control module --or transfer case failure

Oct 19, 2017 | 2000 Chevrolet Silverado 1500

1 Answer

I have a 2000blazer n it goes into 4 auto on its own sumtimes n when i push the 2 hi button it goes into 4 low n wont go back into 2 hi for awhile.whats wrong


it most likely the switch, but the problem with the push button set ups is theres alot of electronics involved. start buy check the switch the next most likely cause is the actuating motor on the t case itself

Mar 19, 2012 | 2000 Chevrolet Blazer

1 Answer

My 4wd will not lock. tried it in park, and neutral. and when i pull up to a stop the idle dies down to 500 rpm. its the push button 4wd the light just flashes when pushed. thought it would be a vacuum...


The most common problem with these would be the transfer case actuator motor or also called the selector, this is what controls the 4wd at trnsfer case, the only other thing would be the button controls they go bad also, you should have the compuetr scanned for any stored codes, the codes will tell you where the problem would be, for example if the computer sees a problem it will turn on a 4wd light or check engine light and sometimes wont turn the light on depending, anyway it stores a code with the problem, example a scan tool is connect to truck connector and computer is scanned for codes and lets say theres a code like p1269 selector motor high voltage, now that code would mean theres a problem in that system,

Dec 28, 2010 | 2005 Chevrolet Colorado

2 Answers

The transfer goes into 4 low when i turn the


if you have access to a lift put somone in it sent it up
start it up put in 4wd low and check to se if the
output shaft is turning from the transfer case to the
front difirential if it's not turning odd's are transfer case problem if it is turning listen each front hub for
grinding noise if there is check the offending hub
by the way if you can't use a lift find some level paved
ground and use 4 STURDY jack stands to do tests
hope this helps any other ? just ask. good luck

Jan 13, 2010 | 1999 Ford Ranger SuperCab

1 Answer

4WD engaged?


turn sharp right or left. if the front feels jerky or fights to go straight your in 4x4 mode. if not disengaging try backing up a few feet after shifting to 2x

Dec 12, 2009 | 1993 Chevrolet S-10 Blazer

1 Answer

2001 Chevy 4WD button lights don't come on - 4WD wont engage


check the solenoid on the front chunk these vehicles have had a lot of problems with these solenoids. have personally replaced about 10 of these on 98-02 models.

Aug 26, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

4wd won't work axles turn electronic box engages front tires won't lock in


have you checked to ensure that the actuator is working? if the actuator isn't working then the ring gear wont engage and won't turn the front shafts. try turning your key to accessory and put the truck in 4wd

May 23, 2009 | 1993 Ford Bronco

1 Answer

98 4runner 4wd hi wont engage


Check you fuse panel to see if you have a fuse blowed???? If not, my father have to instal a new motor that switches itno gear????

Nov 14, 2008 | 1998 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...