Question about 1989 Nissan Stanza

2 Answers

89 nissan stanza L4 1974cc 2.0L sohc---having trouble removing head to repair headgsket. guess i have missed some bolts. do i need to remove distributor, sproket and rocker. i have removed headbolts.

Posted by on

  • majmo34 Apr 24, 2010

    the head has broken loose from the side facing the radiator....however, the side facing the firewall remain stuck....feels like a bolt (s) are holding it down....i thought i had all possible bolts removed, but guess i have failed somewhere along the line...everything about this has been pretty hard for a jackleg......any suggestions would be appreciated....especially the bolt/nut loctions which must be removed to reomove the head,,,,

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,874 Answers

Cylinder head instructions:
Renew bolts: No
Stage 1: Tighten: 29Nm
Stage 2: Tighten: 78Nm
Stage 3: Slacken off: 360 deg.
Stage 4: Tighten: 29Nm
Stage 5: Tighten: 74 ~ 83 Nm

Tightening sequence
89 nissan stanza L4 1974cc 2.0L sohc---having - 555911b.png
Cylinder head gasket is stucked to cylinder block. Use a piece of wood and knock out the cylinder head from cylinder block !

If you want a bigger picture I will need yours e-mail address because the www.fixya.com site has a limited 150 kb of traffic.

Please rate my response. Thanks!

Posted on Apr 24, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 6,826 Answers

How many bolts did you remove?If there is a overhead cam,then there are more likely more bolts under the cam.look for brackets bolted to the head and the block also.

Posted on Apr 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Head gasket tepair on a 92 nissian stanza


you need to strip everything away from the top of engine and take off the cylinder head remove the old gasket and put new gasket on you must use a torque wrench for all the nuts if not youll damage the cilinder head , see haynes manual for your model.

Sep 25, 2012 | 1992 Nissan Stanza

2 Answers

How many torcs for a 92 nissan stanza head gasket


Most NAPA auto parts stores can tell you this

Aug 02, 2012 | Nissan Stanza Cars & Trucks

1 Answer

How do i replace a fuel pressure regulator in a 92 stanza


1992 NISSAN STANZA FUEL PRESSURE REGULATOR REPLACE

Relieve fuel pressure (See procedure below). Remove air duct. Remove accelerator cable bracket. Remove vacuum hose from regulator. Remove fuel return hose from regulator. Remove screws and regulator. Reverse procedure to install.

RELIEVE FUEL PRESSURE
Disconnect fuel pump relay (See Diagram). Start engine and hold at 1600 RPM until engine stall. Turn ignition switch off. Allow engine to cool completely before performing any fuel system repairs.



2_29_2012_2_04_50_am.gif

Feb 28, 2012 | 1992 Nissan Stanza

1 Answer

I need the firing order for a1984 nissan stanza--4cy--2.0---engine # CA20(e) 1974 RLF01A---FD33 Thanks


For 1984 Nissan Stanza (USA) 2.0 liter SOHC L4 (CA20S) check...

zjlimited_242.gif


Hope this helps (remember to rate this answer).

Mar 14, 2011 | 1984 Nissan Stanza

1 Answer

I am trying to replace the starter in my 86 nissan stanza but cant see it


NISSAN STANZA WAGON - Manual Transmission


Q. Where is the starter on a 1986 nissan stanza station wagon and how do you get to it ?


Due to limited access to the starter, it is recommended that the transaxle be removed when servicing the starter.

REMOVAL:

1. Cold vehicle.

Remove 2 mounting bracket bolts, 10 & 12 mm (Figure 1).

Remove top starter motor bolt 14 mm with universal & long extensions.

Raise vehicle on hoist.

Remove front splash pans 10 mm.

Automatic transmission: Drain 2 qts out.

Remove rt-ft wheel 21 mm., & tie rod (Figure 3), axle cap, cotter pin, adj-nut & rubber washer.

Remove ball joint nuts 17 mm., left lower control arm 19mm. & swaybar bracket 14 mm. (Fig 2).

Remove axle nut 36mm (Figure 4), the front tube, catalytic converter heat insulators 10mm, ctr ex-tube 17 mm., and front tube from exhaust system (Figure 5).

Remove long bolt from ft engine mount (next to radiator), 17mm socket (Figure 6, Item A).

Remove tension rod mount 14 mm. Has adj-bracket with rubber insulators (Fig 6, Items B, C).

Remove right side drive shaft bolts that hold shaft to bracket mounted on engine (Fig7) 12mm.

Remove rt-driveshaft.

CAUTION: Transaxle side seals are cut by spline teeth.

Install hoist type transmission jack and wooden block under the transmission/engine. Be certain the transmission is safely balanced on the hoist.

Remove 5 engine crossmember mounts (3 bolts, 2 nuts) 14mm.

Remove nut that attaches crossmember to engine mount.

Loosen stabilizer bar mounts to allow adequate clearance for crossmember to be removed.

Remove following brackets to allow starter assembly to pass through bottom:

tubular support bracket - engine to transaxle

angled support bracket - driveshaft bracket to engine mount

manifold collector stay - (bottom bolts)

Loosen top bolts, remove bracket above driveshaft-holding bracket 14mm.

NOTE: This bracket is slotted to allow it to slide out without completely removing the bolts.

Remove bottom starter motor mounting bolt.

Separate starter assembly from bellhousing, DC all cables/connectors, remove starter motor.

When installing starter, connect cable, install/torque starter bolts.

Nov 03, 2010 | 1986 Nissan Stanza

1 Answer

How do I remove the back seat of my 1991 Nissan Stanza to access the fuel pump? Autozone says to remove rear seat cushion mounting bolts but how do you get to them?


I replaced my rear speakers I had to remove the entire rear seat bottom and top as for the bottom just pull up theres nothing holding it down just a few body clips like the ones that hold the door panels in place

Mar 18, 2010 | 1991 Nissan Stanza

1 Answer

How to change out an ignition switch? any help would be appreciated


The bolts that hold it in place need to be removed with a punch or chisel. The heads break off during installation for security purposes.

Feb 04, 2010 | 1990 Nissan Stanza

1 Answer

How do you change thermostat?


Follow the lower radiator hose and it will lead to the thermostat housing, bolted to the engine with two screws. Remove the two screws, along with the section of metal pipe that the radiator hose is bolted to, remove old thermostat, replace with new thermostat and proper rubber gasket. Bolt housing and metal pipe back onto engine.












Jan 12, 2010 | 1992 Nissan Stanza

1 Answer

Starter


hi clarence,

first of all you need to know what is the starter in order to remove it. if you can trace the big wire that comes from the positive wire of your battery to a big round thing at the bottom part of the engine. that round thing is the starter. before you start removing bolts, remove first that big wire from the positive terminal of the battery. it is normally bolted to the engine by three or two bolts. there are two wires that you need to remove first before removing the starter. a big wire from the battery and a small wire that controls the solenoid of the starter. after you remove the wire, remove the bolts that is holding the starter in place and the starter would drop down. the you can repalce it or repair it.

i hope i was able to solve your problem. please rate me.. tnx.

drcool299

Jul 09, 2008 | 1987 Nissan Stanza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...