Question about 1993 Jeep Grand Cherokee

1 Answer

93 grand cherokee straight 6 has no spark won't start what piece am I looking for?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 84 Answers

No spark..well you might wanna start with spark plugs & coil.If not than check the control module if it working and it giving a signal..you can check it by cranking the car n watch the RPM if it moving while starting..if not moving than you might have a bad module or a bad crank sensor...those are a piece you looking...don't worry about the cam sensor....it had nothing to do with starting...good luck

Posted on Apr 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jeep grand cherokee dies while driving


did you change the fuel filter, very common problem that gets over looked too many times

Nov 25, 2013 | 1999 Jeep Grand Cherokee

1 Answer

1995 Jeep Grand Cherokee Laredo - not getting a spark at the coil


assuming its a 4.0 liter straight 6
the crank sensors go bad and the wire on them frequently get melted to the rear of the #6 exaust tube right were it attaches to cylinder head {the melted wire problem ussually happens after work done in the area of it] if its melted pull it off and see if it will start then tape it up or replace.
you could look up how to check it but they are cheap and easy to install and a new one never hurt nothing.

Mar 23, 2010 | 1997 Jeep Grand Cherokee

1 Answer

I have a 93 jeep grand cherokee, I just did the


Not sure why you disconnected the battery to replace plugs, but try locking and unlocking the drivers door using the key. That should re-set the security system.

Feb 28, 2010 | 1993 Jeep Cherokee Country

2 Answers

93' Grand Cherokee, dont start, no spark,no gas preassure


my 1996 jeep grand cherokee lmtd. won't start did tune up. cranks but no fire. please help. engine code 54 shows up . cam shaft positioning no signal. . tested all circuit. changed cam shaft positioning sensor twice.still cranks did start once ran for 5 min. changed the sensor again. no luck. help please. keith

Sep 10, 2009 | 1993 Jeep Grand Cherokee

1 Answer

93 jep grand cherokee spark issues


Just a thought you might want to check the plug that connects the coil to the wiring loom .......maybe some corrosion .

Jun 26, 2009 | 1996 Jeep Grand Cherokee

1 Answer

93 Jeep Grand Cherokee Won't start


The crankshaft position sensor was seriously problematic in those old jeeps. It's located towards the top of the bell housing slightly to the driver's side I think.

Apr 15, 2009 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...