Question about 1995 Jeep Wrangler

1 Answer

Replace clutch I had a friend replace the clutch and it will not start. it turns over but no fire.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

Did you put the crank sensor back in the top of the bell-housing?

Posted on Apr 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the clutch on my 06 colbalt. I am having trouble getting the car to start. Can you help me?


The basics start there. Fuel and fire.. Do you smell gas coming from the tail pipe when you try to start. Check for fire. What is the car doing, does it turn over?

Apr 06, 2014 | 2006 Chevrolet Cobalt

1 Answer

Hyundai atos 2006 clutch pedal hard and gears change difficult


After replacing the clutch and adjusted the cable and you are STILL having a problem with the clutch (it is a cable clutch not a hydrolic one) have a look at where the clutch enters through the fire wall (engine side) you will see that is has probably collapsed or dented there, for some reason this is a common occurrence with the hyundai. This has happened to mine as well as my friend's atos. This is something that should not happen

Aug 04, 2013 | Cars & Trucks

1 Answer

1985 ford pick up with a 1 ton clutch c5 transmission carborated will not fire


Check your timing. Sounds like the bolt holding the distributor may have come loose and let it turn a bit or your rotor in the cap is loose and not giving spark to the correct cylinder at the correct time.

Sep 23, 2012 | 1985 Ford F150

2 Answers

My 1991 rx7's clutch went so loose that it actually stuck to the floor and the car died. it started drove awhile then repeated the problem. now it won't start; seems like it has no compression


Fixing the clutch, I bet one of the lines had been leaking clutch fluid for quite a while. May top it off, and have a friend stomp down on the clutch to see if you can find the leak and repair it, then make sure to bleed your clutch back off. BTW, do you mean no compression as in the clutch has completely gone, or the engine has lost compression?

Jan 17, 2011 | 1989 Mazda RX-7

1 Answer

The problem is that you have to push the clutch all the way in to get the starter to fire. There must be a switch or something that lets the ignition fire the starter. Well, the starter won't fire...


try this, find switch in back of clutch arm. remove switch and hook wires together from switch. but do not try to start with clutch not pressed down. on most cars its a safety precaution. to prevent from starting if clutch is not pushed. have a good day !! clutch_switch2.jpg This one's almost too easy. All that is needed is to loop a small tie wrap around the clutch switch and switch lever assembly. After cinching it down the switch lever is permanently depressed (thereby eliminating the annoying clicking sound). If it ever becomes necessary to restore the switch to normal operation just cut the tie wrap. Couldn't be simpler. Depending on how long it takes you to find a tie wrap the entire process should take 2 minutes or less. NOTE: It is now possible to start the car without the clutch being depressed. If you do this hack make sure the car is not in gear when the car is started unless the clutch is depressed.

Dec 15, 2010 | 1989 Ford F 250

1 Answer

I push the clutch in to start it but the staarter dont turn


is your battery charged? turn the head lights on while you try to start and have someone look at the headlights while you try to turn engine over, if the headlights dim while the key is turned to start position, that means the starter is drawing fire. if starter does not turn while doing this, i would say bad starter. if not that,,,there is a neutral safety switch on the clutch. just to make sure your car does not start while in gear, the factory installeda switch on the clutch pedal to insure children and minors can not start your car. unless the clutch in pushed in. the switch is on the clutch pedal, just above the brake pedal[pad] look for a plunger type switch above the pedal.. i hope this helps!!!!

Aug 25, 2010 | 1992 Pontiac Grand Am

1 Answer

I have a 89 f250 4x4 and I was pulling a trailer when the clutch pedal went right to the floor.Turns out the line had popped off and now the truck will not start,What holds the line in in the slave end and...


For starter,you must get the clutch line replace 1st.

You will need a friend to bleed the clutch slave cylinder.

Check your owner manual for the correct fluid.....most like be DOT3.

Your problem is cause be the electronic cut out. When you DO NOT press on the clutch it will disable the starter circuit.

IT IS A SAFETY THING.

It prevent someone for start the truck in gear.

Good luck

Jul 18, 2009 | 1988 Ford F 250

1 Answer

Onece in a while turn over wont fire. runs great other wise


your injector or fuel pump may be going out, next time when you check the issue, check your distubutor again and making sure you getting sparks, if you do have sparks than it has to be your fuel problems.

Jun 25, 2009 | 1991 Honda Civic

2 Answers

1987 Suzuki Samurai Clutch problem.


Adjusted Clutch cable assembly under passenger side of vehicle. Had assistance from friend depressing clutch pedal and engaging shift lever. Problem went away

Mar 18, 2009 | 1987 Suzuki Samurai

Not finding what you are looking for?
1995 Jeep Wrangler Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...