Question about 2001 Chevrolet S-10

1 Answer

HOW TO BLEED THE CLUTCH? - 2001 Chevrolet S-10

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

Have someone hold the pedal down. Open the bleeder. Then close the bleeder. Have your helper pump the pedal. Then hold it down. Repeat this about 3-4 times. Make sure the fluid level is full while bleeding.

Posted on Apr 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bleed clutch cylinder for Nissan Sandra 2010


bleed clutch cylinder Robinny, Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Bleeding clutch
Clutch bleed how to
Nissan Altima 2007 2012 Service Manual Clutch fluid On vehicle maintenance...
Help clutch bleeding Fail

Jul 19, 2016 | Nissan Cars & Trucks

1 Answer

Is it true that u need to bleed a clutch on a mits mirage 2001 car?


If you have replaced the clutch master cylinder or slave cylinder,then you do need to bleed,here's a link on how to bleed your clutch. Repair Guides Clutch Hydraulic System AutoZone com

Oct 05, 2015 | Cars & Trucks

2 Answers

How do you bleed a hydraulic clutch on a 1977 corvette


you bleed like you would the brake system. there is a bleeder screw on the slave cylinder that you bleed the system.

Oct 11, 2014 | 1977 Chevrolet Corvette

1 Answer

Where the heck is the reservoir for the clutch master cylinder on my 84 AMC Eagle.


its made on clutch master cylinder under hood straight thru from clutch pedal fill it under hood take small wrench 5/16 I think get under vehicle find slave cylinder bleed valve you will need wrench a piece of vacuum hose and a cup put wrench on bleed valve then put vacuum hose on next the other end goes in cup of brake fluid to prevent air sucking back it can bubble air out but can only suck brake fluid back have helper pump clutch pedal hold pedal bleed repump rebleed till clutch gets right its harder to bleed than brakes pump fast hold pedal down pump clutch fast hold down bleed real pain in *ss good luck

May 21, 2013 | 1984 AMC American Motors Eagle

1 Answer

97 jeep Cherokee clutch will not depress to start the engine


Now you need to bleed the clutch at the clutch slave cylinder down on the transmission to restore the clutch.
Put a wrench on the bleed valve and open it, then lightly close it. Now have someone pump the clutch a couple of times to build pressure. Then while the clutch pedal is slowly pressed down open the bleed valve, then close valve as pedal gets to floor. Repeat this bleed process until a steady stream of brake fluid comes out the bleed valve. Then you should have a good clutch again.

Dec 20, 2012 | 1997 Jeep Cherokee

3 Answers

How do you bleed the clutch hydraulic system on a 2008 Mustang?


you bleed a hydraulic clutch the same way you bleed a brake system and it uses brake fluid as well.you keep bleeding until there is no more air in the clutch system.there should be a bleeder screw on the clutch slave cylinder that is were you bleed the clutch from.

Mar 18, 2011 | 2008 Ford Mustang

1 Answer

Can't get clutch to bleed on 1996 s 10 we have bleed bleed and bleed


Hi if you have done the following to bleed the clutch.
1 open bleed screw
2 push pedal to floor and keep on floor
3 do bleed screw up
4 lift pedal
5 undo bleed screw
6 push pedal to floor
7 do bleed screw up
8 lift pedal up
you need to repeat this a few times but making sure the fluid level dont drop below the lowest level else you will get air in the system.

right now if you have done the above properly and you still either get the pedal going to the floor and staying their or you have no pedal at all then this points to their being a fault with either the clutch master cylinder or clutch slave cylinder, now in most cases the one that fails is the master cylinder this is the one that is connected to the clutch pedal now its usually this one that fails and causes the pedal to go to the floor or have no clutch.

but it could also be the slave so bare this in mind, if the pedal comes back up after pushing it down then the chances are its the slave at fault and this is the one on the gearbox that operates the clutch arm.

let me know how you get on or if you need further assistance ok

plz rate this solution as i have a whole page of unrated posts, thanks

Dec 01, 2010 | Chevrolet S 10 Cars & Trucks

3 Answers

Explain how to bleed a hydraulic clutch on 1996 Ford F-150 5 speed w/ OD


just like you would bleed breaks pump the clutch release the fluid out of the junction

Sep 02, 2010 | Ford F-150 Cars & Trucks

1 Answer

Clutch pedal stays 2 the floor on a hydralic clutch system on a 2000 camaro v8. clutch master cylinder is new also slave cylinder and clutch and pressure plate


Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

Sep 06, 2009 | 2000 Chevrolet Camaro

Not finding what you are looking for?
2001 Chevrolet S-10 Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...