Question about 2004 Chevrolet Monte Carlo

1 Answer

The add brake fluid light came on and the resever is full

Posted by on

  • bencjr May 11, 2010

    My car blew a fuse after a hard stop. Did you check the fuses ?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 291 Answers

Should be a wiring harness that goes to the master cylinder at the bottom of the resevor.. unplug this does light go out if so the level sensor in resevor is bad

Posted on Apr 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

ABS LIGHT AND BRAKE LIGHT ARE ON


Check the brake fluid level and add if needed. If the fluid is low ...I would inspect the brake system. Inspect brake pad thickness and check for any brake fluid leaks. If the fluid is full and the abs light is still on..the code or codes will need to be retrived from the ABS Module to determine what part of the system is having a fault.

Nov 20, 2012 | 2003 Ford Expedition

1 Answer

Red brake warning light comes on when the car turns a corner or comes to a stop.


fluid is low probably due to worn brake pads. factory specs are dot 3 fluid. fill to full line. may need a flashlight and a funnel to add the fluuid. hope this helps

Aug 30, 2012 | 1998 Chrysler Town & Country

1 Answer

Emergency brake light stays on also battery light on


Assuming there is not a problem with the parking brake (as in a stuck switch), the red "BRAKE" light will remain on if your brake fluid is low (for your regular service brakes). Check your fluid, and if it is low, check your brakes and brake lines to be sure there isn't a leak somewhere, as this could be dangerous!

Brake fluid level will drop slightly as your brake pads/shoes wear over time. If you need brake pads or shoes, avoid topping the fluid off, as it will overflow when you go to compress the pistons in the calipers later on (when changing your brake pads). If you MUST add fluid, only add to the "FULL" mark. If you have a leak, remember the brakes must be bled after you repair the leak.

The battery light signifies a charging problem. You will need to check the output of your alternator, as in volts AND amps. Usually a local garage will be able to perform a quick (and cheap) check of your charging system. Check your battery too, to be sure that it holds a good charge.

Jul 02, 2011 | 1995 Nissan Pickup

1 Answer

Need to add brake fluid to my 2003 Pontiac Aztek. Can you provide a checklist for me to follow?


The checklist?? You MUST have a sealed container of brake fluid, so you have no moisture in the fluid.

BUT...if you need to add fluid, the indication is that you may be close to replacement time on you brake pads. Here is the deal: if you have full reservior and new brake pads,.... it takes about one reservoir of fluid to make up for full brake pad consumption. What this means is: IF you were to fill up the reservior, then fluid needs to be removed when you replace the pads.

I suggest that you consider replacement of the brake pads, then flush brake fluid and top it up.

Feb 06, 2011 | Pontiac Aztek Cars & Trucks

2 Answers

My brake light did not warn me that i needed brakes


someone probably topped off your brake fluid when your brakes were low. the only way i know is to have new front and back brakes then make sure the brake fluid level is right . the light only comes on if your brake fluid goes low so the system has too much fluid if it says full and your brakes are not new front and back

Dec 16, 2010 | 2005 Mercury Mountaineer

3 Answers

Brake pedal travel long-slow to stop.


check your front brake pads and see if they need replaced then check your brake fluid after you change them. If you add brake fluid first you will leak brake fluid out when you compress the calipers to change the front brake pads. In the end make sure your brake master cylinder is full of dot 3 brake fluid before you drive.

Dec 11, 2010 | 1996 Ford Taurus

1 Answer

What is the problem when i see a red light in the left hand side of the dash board which looks like a basin when iam driving sometimes on a slope or when the foot is on the accelerator or cratch? what...


it means you are low on brake fluid if that is your brake light and you need add fluid maybe have a leak if fluid real low it could also be your car is low on oil too as well check all your fluids and this will go away add any that are low fill to the full line on them all

Sep 24, 2010 | Mitsubishi Passenger Cars & Trucks

3 Answers

WHERE DO I CHECK..ADD BRAKE FLUID


Hi:
when you open the hood, on the back wall on the drivers side is your brake fluid reservoir. It is a clear plastic tank with a black lid. Usually there is a line on the side to see the level of the brake fluid. If you can see the fluid is to the line, you are good to go. If it looks low, then you need to unlatch the lid and pour in brake fluid till it is at the full line

Nov 19, 2009 | 1997 Plymouth Voyager

1 Answer

Not going into gear


have you checked your brake lights? are they working? most cars have a safety feature that require a signal from brake lights (by stepping on brake pedal) to activate a relay to disengage the shifter interlock, OR can you move the gear selector into gear, and it just won't move? is it an automatic or stick shift ? If it's an automatic start the car, after it has ran for 5 - 10 minutes check the trans fluid dipstick, it should have fluid level between add / full marks , if not add or remove fluid as necessary. If is a manual trans, it is possible the clutch is bad. need more info on vehicle, how many miles? engine size?

May 31, 2009 | 2000 Hyundai Elantra

Not finding what you are looking for?
2004 Chevrolet Monte Carlo Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...