Question about 1988 GMC S-15

1 Answer

Replace u joint on GMC S15 pickup

Replace u joints on 1988 GMC S15 pickup

Posted by on

  • Dennis Roughley Apr 25, 2010

    Where is the answer to my question. All you give me is a list of makes of cars. This was a waste of my frickin time

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

You'll need a bench vice for this. A few sockets help as well. Once you get the shaft off the truck, put a smaller diameter socket on one side and a much larger diameter socket on the other and sandwich in a vice. Compress vice to drive the U-Joint through shaft (smaller socket will drive the one side through the other with the much larger socket). Installation is the reverse of removal.

Posted on Aug 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

High idle gmc 1988 s15 poor fuel economy no check engine light


Change the temperature control sensor to the front if the engine near radiator
1 start the truck let it run till you think it is at normal operating temperature
2 unplug the temp sensor if the idle changes then the sensor is bad

Feb 08, 2014 | 1988 GMC S-15

1 Answer

Why does my rear wheel drive s15 have vibiration in front drivers side while driving on highway?


Have tire balance checked, and also have the steering and suspension components(tie rods, ball joints) checked. Could also be a shifted belt in the tire, this will show up during tire balancing.

Sep 24, 2011 | 1985 GMC S-15

1 Answer

What a/c system did the 1988 gmc s15 pickup use? do i need to worry about messing with freon?


it used r-12 and the system should be evacuated, different oil put into the system and new fittings installed on the low and high pressure ports, then filled with 134a-use a little less than what the r12 capacity calls for as well.

Dec 23, 2010 | 1988 GMC S-15

4 Answers

2005 gmc seirra vibration around 50 mph


It sounds like a bad U-joint to me. The only way to properly check u-joints is by removing the driveshaft. The joint should move freely, any binding will cause the vibration.

Mar 28, 2010 | 1995 GMC Sierra C1500

1 Answer

Can't figure out how to remove the old upper ball joint for the a arm how would i do it?Also where is the idler arm located on the same vehicle. The vehicle is a 93 gmc jimmy s15


I get the feeling you have never done this kind of work before. If you need to know where things are,leave it to a repair shop. Would love to teach you but do not have vehicle.

Sep 29, 2009 | GMC Jimmy Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

250 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...