Question about Ford Ranger

1 Answer

Sorry emmisionwiz I guess you didn't see my comments posted the truck is a 1993 ford ranger with 3.0 standard tranny 2 wheel drive. The truck came through without an egr. that is why I am confused as to why I get code 33

Posted by on

  • 4 more comments 
  • glcs Apr 24, 2010

    Sounds good but how do i stop light from coming on. the inspection is coming up and it will be rejected if light is on. I am in Rhode Island

  • glcs Apr 24, 2010

    I put new plugs, wires, cap rotor, map sensor, ignition modual, and idle control valve. is there anything in addition to o2 sensors to look at. The code has been reset a few times and alwaws comes back. Additional information the light comes on after five minutes of operation and if ignition is shut off and turned back on the light will go off then come back in another five minutes. not sure if that means anything or not

  • glcs Apr 24, 2010

    The truck has 112,000 miles on it. Bought it from an elderly gentleman. It was in very poor running condition when i got it but got better with each thing that was replaced. It seems to run very strong now. but the light is driving me nuts, and as mentioned need to get state inspection done :(

  • glcs Apr 24, 2010

    Thanks, I will put the o2 sensors in and use the intake cleaner as recomended tomorow after work. After that I will clear the codes and drive for 100 miles then post back the results,most likely Sunday afternoon.

  • glcs Apr 26, 2010

    Replaced O2 sensors & cleaned intake but still getting code 33. Perhaps I need to drive the truck for a while before clearing codes? There is a mention about the PCM being programed to a vehical with or without an egr. Is there a way to reprogram it or tell if it was replaced with the wrong PCM before I purchased this truck?

  • glcs Apr 26, 2010

    Yes, there is a place for an egr but it has a factory cover on it. The 1993 rangers with the 3.0 and standard tranny dose not have one. the 93s with the automatic do have the egr. I double checked this at a few parts stores and there is no listing for that part on 93s with standard tranny. also the emmisions tag/diagram under the hood shows no egr. I am going to check with the dealer about egr or no egr for this truck. THANKS for the help so far!

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,926 Answers

The code is normal, this is due to no EGR. Your PCM is programed to a vehicle that has an EGR or one without an EGR. It is the same as receiving a 55 no code or a 12.

Posted on Apr 24, 2010

  • 2 more comments 
  • GetMeOttaHere Apr 24, 2010

    Disconnect the battery for about 1 minute. If this does not reset,you can bring it to an Autozone and they can delete the code for you. If the code comes back, you have another problem with an engine management component....possibly O2 sensor related, or may be as simple as spark plug replacement. I don't know what was discussed previously with the other expert.

  • GetMeOttaHere Apr 24, 2010

    Spray out the throttle body with intake cleaner....do not use carb cleaner. At this point, with all the parts you replaced, you may as well replace the O2 sensor as I feel this may be the direct cause.

    You did not mention how many miles are on this vehicle? Just need to know where we stand from a mechanical standpoint.

  • GetMeOttaHere Apr 26, 2010

    You stated the truck came through without an egr, what is meant by this? Is there a place for one. I'm thinking there shuld be, and I must not have understood your first post.

  • GetMeOttaHere Apr 27, 2010

    Have you tried disconnecting the negative lead for about 30 seconds to see if this makes a diiference?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What can be wrong with my truck transmission?


I would guess the torque convertor has failed and you need it replaced

Jan 14, 2016 | Cars & Trucks

1 Answer

Transmission


I am guessing an automatic. Drain the tranny and clean the governor. Replace and refil the fluid. Inexpensive if you reuse the fluid and not too time consuming.

Apr 26, 2014 | 1993 Ford Ranger SuperCab

1 Answer

Need to know what 5 speed transmissions will interchange with a 92 ranger with a 3.0


You didn't mention if it was 2 or 4 wheel drive so I went with a 2 wheel drive. According to hollander the 5 speed transmaaion fits a ranger (2WD) 1991 - 1994 and a Mazda B3000 1994 only. Hope this helps.....

Oct 29, 2012 | 1992 Ford Ranger

1 Answer

I HAVE A 1993 FORD RANGER 3.0 V6 ENGINE AND NEED


For 1993 Ford Truck Ranger 4WD 3.0L MFI 6cyl the Control Module-Ignition is located under hood, center, rear engine area, mounted on distributor.

f2a2c92.jpg

Fig. 1: View of the remote mounted Ignition Control Module (ICM)

Hope this help (remember comment and rated this).

Jul 27, 2010 | 1993 Ford Ranger SuperCab

1 Answer

I need to know what u use to remove the driveshaft from a 93 ford ranger


make sure you block the wheels and apply the e brake. it only takes the right size wrench on the back by the axle then pull it out of the transmision if you dont plug the end of your tranny all the fluid will run out

Jan 31, 2010 | 1993 Ford Ranger SuperCab

1 Answer

MY TRANNY WENT OUT LAST NIGHT. I WAS REVVING IT TO


yes your tranny is shot if you have it in gear it should move. sorry :(

Nov 12, 2009 | 1993 Ford Explorer Limited

1 Answer

1993 FORD RANGER 4 WHEEL DRIVE


there is an actuator on the back of the transfer case that likes to fail odds are this is where your problem is. check power and ground here and if you have both replace the actuator

Nov 22, 2008 | 1993 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...