Question about 1989 Ford Bronco II

Open Question

How do I adjust the clutch pedal to a lower position?

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

aliensanity
  • 24 Answers

SOURCE: clutch pedal not returning to position

Under the dash look to see if there is a spring attached to the petal or maybe under the hood. Or you might have something getting in the was of the petal arm. Good Luck and PEACE

Posted on Jun 13, 2008

  • 3 Answers

SOURCE: clutch adjustment

I had a similar problem on my 88 mustang.  The stock set up has two  adjustable parts called the quadrant and the paul.  You can find them by getting underneath the steering wheel and looking up.( In a very uncomfortable position.)  When you move the pedal watch for the quadrant to move, and that's how you locate it.  Pull the clutch pedal towards the seat, and push on the quadrant to reset it.By doing so, the clutch should adjust itself where it needs to go, the next time you push on the pedal.  I ended up replacing mine with a Steeda aluminum quadrant and clutch adjuster, because the two stock pieces are plastic and broke on me.

Posted on Aug 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the code p1589 with fcar scanner


MULTI-MODE MANUAL TRANSAXLE SYSTEM ADJUSTMENT
1. USING INTELLIGENT TESTER: CLAMP POSITIONADJUSTMENT (CLUTCH POSITIONADJUSTMENT)
Tech Tips
The multi-mode manual transmission system has a load controlled clutch cover (adjustment system). The pressure plate moves depending on the wear
condition of the clutch disc lining.
When removing or installing any parts related to the multi-mode manual transmission system, move the clutch actuator to the clutch clamp position. This is
for normal operation of the load controlled clutch cover (adjustment system).
If the clutch position adjustment operation input fails, perform the operation again from step (a) more than 15 seconds after turning the ignition switch off.
Note
Do not depress the brake pedal while performing the clamp position adjustment using an intelligent tester.
a. Prepare the vehicle:
Stop the vehicle.
Shift the lever into the N position.
Turn the ignition switch off.
Apply the parking brake.
b. Connect the intelligent tester to the DLC3.c. Turn the ignition switch on (IG).
d. Turn the intelligent tester ON.
e. Select the following menu items: Powertrain / Multi-Mode M/T / Utility / Parts Exchange.
f. Read the information.
g. Press the Next key.
h. Read the information.i. After checking the vehicle condition, press the Next key.
j. Read the information.
k. Press the Next key.
l. Read the information.m. Press the Next key.
n. On the Multi-Mode M/T / Utility screen, select Step 1 Clutch Position Adjustment (Clamp Position Adjustment).
o. Press the Next key.
p. Read the information.q. Press the Next key.
r. Complete Clutch Position Adjustment.
s. Turn the intelligent tester OFF.
t. Turn the ignition switch off.
u. Replace the malfunctioning parts.
Tech Tips
Perform [Initialization and Learning] after repairing the multi-mode manual transmission control system .
2. WITHOUT USING INTELLIGENT TESTER: CLAMP POSITIONADJUSTMENT (CLUTCH POSITIONADJUSTMENT)
Tech Tips
The multi-mode manual transmission system has a load controlled clutch cover (adjustment system). The pressure plate moves depending on the wear
condition of the clutch disc lining.
When removing or installing any parts related to the multi-mode manual transmission system, move the clutch actuator to the clutch clamp position. This is
for normal operation of the load controlled clutch cover (adjustment system).
If the clutch position adjustment operation input fails, perform the operation again from step (a) more than 15 seconds after turning the ignition switch off.a. Prepare the vehicle.
Stop the vehicle.
Shift the lever into the N position.
Turn the ignition switch off.
Apply the parking brake.
b. Using SST, connect terminals TC and CG of the DLC3
SST
09843-18040
c. Turn the ignition switch on (IG) with the brake pedal released.
d. Depress the brake pedal 7 times or more within 3 seconds.i. The buzzer sounds twice with an interval of 0.25 seconds.
e. Depress the brake pedal.
f. Shift the shift lever in the following sequence with the brake pedal depressed: N?E?M?+?M?+?M?+?M?+?M?E?N.
g. Release the brake pedal.
h. Depress the brake pedal again.i. The buzzer sounds at intervals of 0.5 seconds as follows (an interval of 2.5 seconds exists between each cycle).
Once when adjusting the clutch clamp position (one cycle)
Tech Tips
If the buzzer does not sound at this time, wait at least 15 seconds after turning the ignition switch off. Then, perform the procedure from step
(a) again.
i. Depress the brake pedal 3 times or more within 2 seconds.
i. The buzzer sounds twice with an interval of 0.25 seconds.
j. Depress the brake pedal.
k. Shift the shift lever to the [-] position with the brake pedal depressed.
l. Release the brake pedal.
m. Complete clutch position adjustment.
n. Turn the ignition switch off and wait at least 10 seconds.
o. Disconnect the SST from terminals TC and CG of the DLC3.
p. Repair the malfunctioning parts.Tech Tips
Perform [Initialization and Learning] after repairing the multi-mode manual transmission control system .

May 22, 2015 | 2009 Toyota Yaris

1 Answer

How do u adjust clutch pedal


You adjust the pedal height by turning the clutch master cylinder pushrod which is attached to the clutch pedal under the dash. Loosen the locknut and turn the rod to raise or lower the clutch pedal. Don't forget to tighten the locknut when done

May 06, 2014 | 1991 Honda Accord

2 Answers

The clutch pedal is too high. how to adjust in order to lower the clutch pedal


its a automatic adjusting cable on this vehicle so if pedail too hight then its a new clutch

Apr 25, 2011 | 1996 Volkswagen Jetta

2 Answers

How to adjust clutch pedal on 86 mustang lx


clutch is supposed to be self adjusting. Here are instructions for replacing the adjuster:


REMOVAL & INSTALLATION


See Figure 1

  1. Disconnect the battery cable from the negative terminal of the battery.
  2. Remove the steering wheel using a steering wheel puller, Tool T67L-3600-A or equivalent.
  3. Remove the lower dash panel section to the left of the steering column.
  4. Remove the shrouds from the steering column.
  5. Disconnect the brake lamp switch and the master cylinder pushrod from the brake pedal.
  6. Rotate the clutch quadrant forward and unhook the clutch cable from the quadrant. Allow the quadrant to slowly swing rearward.
  7. Remove the bolt holding the brake pedal support bracket lateral brace to the left side of the vehicle.
  8. Disconnect all electrical connectors from the steering column.
  9. Remove the 4 nuts that hold the steering column to the brake pedal support bracket and lower the steering column to the floor.
  10. Remove the 4 booster nuts that hold the brake pedal support bracket to the dash panel.
  11. Remove the bolt that holds the brake pedal support bracket to the underside of the instrument panel, and remove the brake pedal support bracket assembly from the vehicle.
  12. Remove the clutch pedal shaft nut and the clutch pedal, as outlined above.
  13. Slide the self-adjusting mechanism out of the brake pedal support bracket.
  14. Examine the self-adjusting mechanism shaft bushings on either side of the brake pedal support bracket, and replace if worn.

To install:
  1. Lubricate the self-adjusting mechanism shaft with motor oil and install the mechanism into the brake pedal support bracket.
  2. Position the quadrant towards the top of the vehicle. Align the flats on the shaft with the flats in the clutch pedal assembly, and install the retaining nuts. Tighten to 32-50 ft. lbs. (43-67 Nm).
  3. Position the brake pedal support bracket assembly beneath the instrument panel, aligning the four holes with the studs in the dash panel. Install the four nuts loosely.
  4. Install the bolt through the support bracket and into the instrument panel. Tighten to 13-25 ft. lbs. (18-34 Nm).
  5. Tighten the four booster nuts that hold the brake pedal support bracket to the dash panel to 13-25 ft. lbs. (18-34 Nm).
  6. Connect the brake lamp switch and the master cylinder pushrod to the brake pedal.
  7. Attach the clutch cable to the quadrant.
  8. Position the steering column onto the four studs in the support bracket and start the four nuts.
  9. Connect the steering column electrical connectors.
  10. Install the steering column shrouds.
  11. Install the brake pedal support lateral brace.
  12. Tighten the steering column attaching nuts to 20-37 ft. lbs. (27-50 Nm).
  13. Install the lower dash panel section.
  14. Install the steering wheel.
  15. Connect the battery cable to the negative terminal on the battery.
  16. Check the steering column for proper operation.
  17. Depress the clutch pedal several times to adjust the cable.
  18. 714c4a4.gif

Sep 24, 2010 | Ford Mustang Cars & Trucks

1 Answer

Info on do it tyour self clutch removal on 2001 mustang 3.8


REMOVAL:
  1. Lift clutch pedal to uppermost position to disengage clutch and brake pedal pivot shaft.
  2. Push clutch and brake pedal pivot shaft forward and unhook clutch release lever cable from clutch and brake pedal pivot shaft and allow it to slowly swing rearward.
  3. Raise and support vehicle.
  4. Remove clutch release lever dust shield.
  5. Disconnect clutch release lever cable from clutch release shaft.
  6. Remove retaining clip, then clutch release lever cable from flywheel housing.
  7. Remove starter motor from flywheel housing, then engine rear plate to front lower flywheel housing bolts.
  8. Remove transmission.
  9. Remove flywheel housing back just far enough to clear clutch pressure plate, then remove housing.
  10. Remove clutch release shaft from flywheel housing by pulling it through window in flywheel housing until retainer spring disengages from pivot.
  11. Remove clutch release hub and bearing from clutch release shaft.
  12. Loosen six clutch pressure plate bolts evenly to release spring tension gradually and avoid distorting clutch pressure plate. If same clutch pressure plate is to be installed, mark plate and flywheel so pressure plate can be installed in its original position.
  13. Remove clutch pressure plate and clutch disc from flywheel.
INSTALLATION:
  1. Position clutch disc and pressure plate assembly on flywheel, noting following:
    1. Three flywheel housing to block dowels on flywheel must be properly aligned with clutch pressure plate.
    2. Bent, damaged or missing flywheel housing to block dowels must be replaced.
    3. tart clutch pressure plate bolts but do not tighten.
    4. Avoid touching clutch disc face, dropping parts or contaminating parts with oil or grease.
    5. Align clutch disc using suitable alignment tool inserted in pilot bearing.
    6. To avoid clutch pressure plate distortion, alternately tighten bolts a few turns at a time, until they are all tight, then tighten to specifications.

  2. Install transmission to flywheel housing.
  3. Install engine rear plate to flywheel front lower housing bolts, then connect clutch release cable to flywheel housing and connect retaining clip.
  4. Connect clutch release lever cable to clutch release shaft, then install clutch release lever dust shield.
  5. Install starter motor.
  6. Lower vehicle, then install clutch release lever cable as follows:
    1. Lift clutch pedal to disengage clutch and brake pedal pivot shaft.
    2. Push clutch and brake pedal pivot shaft forward and hook end of clutch release lever cable over rear of clutch and brake pedal pivot shaft.

  7. Cycle clutch pedal several times to adjust clutch release lever cable

Aug 08, 2009 | 2001 Ford Mustang

1 Answer

How to adjust clutch brake on a eaton 2800 series clutch which is installed in a 2004 sterling dump truck


This is from http://refrigeratedtrans.com/mag/transportation_replace_original_equipment/

"A good clutch adjustment begins by identifying the location of the bearing. It should be positioned 1/2" to 9/16" from the clutch brake."

"After the bearing is set, adjust the truck linkage to allow the clutch brake to squeeze a .010" feeler gauge between the bearing and clutch brake when the pedal is no more than 1" to 1.5" from the floor. Setting the clutch brake position too far from the floor reduces the stroke to the clutch and could cause release problems and reduce brake life.
All that remains is checking the free-pedal distance in the cab. With the pedal in the up position, there should be 1" to 3" of free pedal. The clutch is now adjusted correctly."

Apr 21, 2009 | 2004 Ford Super Duty F 450

1 Answer

2002 Civic Dx Clutch?


i have just replaced an 03 civic ex clutch and transmission bearings due to a customer being too harsh on it. It sounds like its got a little life left in it if you are easy on it. 

if there is adjustment in this model use the below walkthrough to adjust it.

adjust the clutch pedal, 

1. if you look up on the top of the clutch pedal, the first thing you should see if a clutch pedal position switch, and right behind it there is a locknut, looens the locknut. once you loosen it, back off on the pedal position switch or adjusting bolt untill it no longer touches the clutch pedal. 

2. now behind the clutch pedal, there is a pushrod. and on that pushrod, there is a locknut, loosen that locknut. Now turn the pushrod in or out to get the desired height and stroke at the clutch pedal. 

The freeplay is the amount of push on the clutch pedal to where is starts to have resistance from the top. I have usually been told it should be set at 1 1/2-2 inches of freeplay.

Once you set it, tighten the locknut on the pushrod. With the clutch pedal released, turn in the clutch pedal position switch untill it contacts the clutch pedal. then turn it an additional 3/4 to 1 turn. And tighten the locknut.

Now on top of the clutch pedal switch, there is a clutch interlock switch. Loosen the locknut on that switch. then press the clutch pedal to the floor.

release the clutch pedal 15-20 mm (0.59-0.79 in) from the fully pressed position, and hold it there. adjust the position of the clutch interlock switch so the engine will start with the clutch pedal in this position. then tighten the locknut on that switch.

Hope this helps 

Nov 28, 2008 | 2002 Honda Civic

2 Answers

Clutch slipping


first i would try adjusting the clutch cable because commonly people with think that they're clutch is going out when really just the cable has gotten stretched....try adjusting that first and if that works then you should be fine for another couple thousand miles but if you want to not have to worry bout it for awhile i would just replace teh clutch assembly....usually ranges from $200 to $450 depending on the clutch set and the mechanic that does the work for you. Let me know what happens. :)

Oct 01, 2008 | 1990 Peugeot 405

2 Answers

Clutch check


you have civic SI type R with the K20A engine and 6sp transmission? correct?

yes the clutch is adjustable.

  1. loosen the clutch pedal position switch(lower of the 2 switches) locknut and back off the clutch pedal position switch.
  2. loosen the clutch push-rod locknut and turn the push-rod in or out to get the desired height and stroke of the pedal.
  3. tighten the push-rod locknut
  4. with the clutch pedal released, turn the clutch pedal position switch in until it contacts the clutch pedal.
  5. turn the clutch pedal position switch in an additional 3/4 to 1 turn.
  6. tighten the clutch pedal position switch locknut.
  7. loosen the clutch interlock switch(the upper switch) locknut and then the interlock switch.
  8. press the clutch pedal to the floor.
  9. release the pedal about 1/2 in. from the fully depressed position, and hold it there. adjust the position of the interlock switch so that the engine will start with the clutch pedal in this position.
  10. tighten the interlock switch locknut.
clutch pedal stroke should be: 5.1 - 5.5 in
clutch pedal height should be: 7.76 in

if adjusting the clutch doesn't help with the transmission feeling notchy, may be the syncros.




Jul 09, 2008 | 2002 Honda Civic

2 Answers

Front wheel Drive query


DEar Customer,

your from is that your car is front wheel drive & you have to reset your car clutch point that loose its sensitivity as they had before,

its not a big prib you have to open bonet than make more active clutch wire with streching clutch joints.

THNX

May 17, 2008 | 1991 Peugeot 405

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...