Question about 1989 Chevrolet Corvette

1 Answer

Raising and lowering the head lights for 89

Raising and lowering the head light on the right front side for 89 corvette

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Check power to assembly- see if motor runs--if it does, gear must be rebuilt. parts thru Rodney **** follow instructions

Posted on Nov 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the radio wiring color diagram for my delco radio, 1998 corvette


1998 Chevrolet Corvette Car Stereo Radio Wiring Diagram
Radio Constant 12V+ Wire: Orange
Radio Switched 12V+ Wire: Yellow
Radio Ground Wire: Black
Radio Illumination Wire: Gray
Radio Dimmer Wire: Brown
Radio Power Antenna Trigger Wire: Pink
Radio Amplifier Turn On Trigger Wire: N/A
Front Speakers Size: 4? Speakers
Front Speakers Location: Kick Panels
Left Front Speaker Wire (+): Tan
Left Front Speaker Wire (-): Gray
Right Front Speaker Wire (+): Light Green
Right Front Speaker Wire (-): Dark Green
Rear Speakers Size: 6?
Rear Speakers Location: Rear Sides
Left Rear Speaker Wire (+): Brown
Left Rear Speaker Wire (-): Yellow
Right Rear Speaker Wire (+): Dark Blue
Right Rear Speaker Wire (-): Light Blue

Dec 22, 2016 | Cars & Trucks

1 Answer

Where is the starter located on 89 vet? Was told


pass side of block in front of flywheel shield

May 09, 2010 | 1989 Chevrolet Corvette

1 Answer

How to change 2005 Corvette fog light bulb


Fog lights are simple, but tight as you would expect.

You will need to jack up the front.

Remove the front fascia closeout panel and right and left lower cowl/spoiler.

Un plug the electrical to the back of the foglight, reach up in and unscrew the bulb. A bit tight. It is about a half or three quarter turn. Pull the old bulbs out.

Install in reverse.

You may need to adjust the beam if you tug to much.

Once you remove the access panel and then pull the brake cooling duct out of the way (just snaps in place...).

It was not necessary to remove the small air-dam corners on my car (nor is it specified in the service manual), but it it make the job easier, it is only two or three screws per side.

Thank you for suing fixya and be safe

Apr 18, 2010 | 2005 Chevrolet Corvette

1 Answer

The passenger head light on my 89 corvette doesn't open but if i turn the knob on the headlight motor it may work once or twice and then it won't work again


this is a common problem mine does it the gears in the motor are stripped look on ebay a u can buy replacment gears with instructions.

Oct 21, 2009 | 1989 Chevrolet Corvette

1 Answer

Removing the whole pop head lights assembly from my 1997 corvette


Raise the headlights, either with the switch or manually by turning the knob on the headlight motor counter-clockwise.
Unplug the lights NOW to avoid an accidental closing on your fingers,
Remove the 3 philips screws holding the black plastic surrounding the headlights, and slide it forward, there is a small clip on the top that helps hold it to a corresponding clip at the top of the headlight,
Look inside the cavity and you can see the 5 nuts/bolts ( 6 on later years ) that need to be removed,
If you are on the driver's side you can now remove the whole assembly, on the passenger's side you must first unplug the headlight door control module.

Aug 25, 2009 | 1998 Chevrolet Corvette

1 Answer

How to 1998 Taurus altenator R&R


please rate highly if this helps
Generator 3.0L (2V)
Removal
  1. Partially raise the vehicle on a hoist. Refer to Section 00-02 .
  2. Remove the right front wheel. Refer to Section 00-02 .
  3. Remove the lower fender splash shield retainers and position the shield out of the way.
  4. Lower the vehicle.
  5. Remove the accessory drive belt from the generator pulley. Refer to Section 03-05 .
  6. Remove the power steering line bracket and heater hose support bracket from the generator.
  7. Remove the upper generator bolts.
  8. Remove the generator splash shield.
  9. Raise the vehicle.
  10. Disconnect the electrical connector and remove the battery positive cable from the generator.
  11. Position an adjustable stand to the subframe.
  12. Remove the right subframe bolts.
  13. Remove the lower generator bolt.
  14. Disconnect the right hand stabilizer link.
  15. Lower the subframe to provide clearance.
  16. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Connect the right hand stabilizer link and torque to 47-62 Nm (35-46 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Section 03-05 .
  1. Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B + cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
3.0L (4V)
Removal
  1. Disconnect the battery ground cable. For additional information, refer to Section 14-01 .
  1. Remove the accessory drive belt from the generator pulley. Refer to Section 03-05 .
  1. Remove the power steering line bracket and heater hose support bracket from the generator.
  1. Remove the upper generator bolts.
  1. Partially raise the vehicle on a hoist. Refer to Section 00-02 .
  1. Remove the right front wheel. Refer to Section 00-02 .
  1. Remove the lower fender splash shield retainers and position the shield out of the way.
  1. Remove the generator splash shield.
  1. Raise the vehicle.
  1. Disconnect the electrical connector and remove the battery positive cable from the generator.
  1. Position an adjustable stand to the subframe.
  1. Remove the right subframe bolts.
  1. Remove the lower generator bolt.
  1. Lower the subframe to provide clearance.
  1. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Section 03-05 .
  1. Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B+ cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
  1. Connect the negative battery cable.
3.4L (4V)
Removal
  1. Disconnect the battery ground cable (14301). Refer to Section 14-01 .
  1. Remove the right side cowl vent screen. Refer to Section 01-02 .
  1. Raise the vehicle and remove right front wheel assembly. Refer to Section 00-02 .
  1. Remove right tie-rod. Refer to Section 11-02 .
  1. Remove accessory drive belt (8620) from generator. Refer to Section 03-05 .
  1. Disconnect electrical harness connector and output terminal wiring.
  1. Remove nut and position engine control sensor wiring (12A581) out of the way.
  1. Remove the two bolts and one stud bolt.
  1. Remove generator from vehcile

May 12, 2009 | 1998 Ford Taurus

1 Answer

How do i change rear turn signal bulb on 89 corvette, notmine???


Rear Turn Signal, Brake and Parking Lights 1984–89 VEHICLES
  1. If removing an inner bulb, remove the license plate. For outer bulb replacement, reach from under the vehicle.
  2. To remove the inner rear brake light, you must reach behind the license place and under the vehicle to access the bulb and socket
  3. Remove the socket from the lens by releasing the locking tab and twisting
  4. Once the bulb and socket are pulled from the rear of the lens, grasp it from behind the license plate opening
  5. Then, pull it out of the side and replace the bulb
  6. Remove the bulb from the socket and replace.
  7. Installation is the reverse of the removal procedure.

Apr 05, 2009 | 1989 Chevrolet Corvette

1 Answer

Replace front turn signal lights in 2000 vette


You have to raise the vehicle a little. Remove the front bumper lower closeout panel.Pull the brake caliper cooling duct out of the way and reposition it. Now you can get to the turn signal socket.

hope this will help you.

Jan 09, 2009 | 2000 Chevrolet Corvette

1 Answer

My head light are real low how do i raise them?


There are adjusting screws on the headlight mounts, three of them I think. You may need a torx or allen wrench. Shine your low beams at the garage door or something and make the adjustments. Be careful not to let the low beams shine in other drivers' eyes. When you think it is right, park at night where you can walk in front of the car 100 feet or so and see that the low beams are not too high. The driver side light should point straight ahead, the passenger side light somewhat to the right.

Nov 15, 2008 | 1997 Chevrolet Tahoe

1 Answer

Side marker lights not working voltage only at left front socket


the front white side marker lights come on with the turn signals to light your way around corners they dont blink they just illuminate the right or left corners the ones at the rear left and right come on with the back up lights,, i have a 86 vette too look for ground wire problems as they are more common on these cars, you may have voltage at the light socket but if its not grounded good no light s

Jul 20, 2008 | 1986 Chevrolet Corvette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...