Question about 1995 Geo Metro

Open Question

How do you replace the timing belt on a 1996 geo metro and how do you start to adjust the time when the belt was broken and don t how where to start to set time

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 119 Answers

SOURCE: How to set a timing belt for a 1992 GEO Storm

Here you are:

137fd9e.png

Posted on Jun 01, 2008

  • 1 Answer

SOURCE: Geo metro timing

how to put the timing chain back on the engin. what i need too know is how too set the point up?

Posted on Jun 22, 2008

captaynkyrk
  • 170 Answers

SOURCE: how to change water pump in 1996 geo metro?

I've found the Haynes Repair Manual that you can get at Auto Zone to be the best one there is. They have step by step instructions with pictures on repairing or replacing just about anything on your auto. You can get them for around $20 - 25. Is yours a 3 or 4 cylinder? Auto Zone has a new service where you can actually look up repair instructions for your vehicle with pictures. Here's the instructions for a 3 cylinder for your year, make and model:

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
CAUTIONWhen draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Remove the air cleaner assembly.
  2. Loosen but do not remove the four coolant pump pulley bolts.
  3. Raise and support the vehicle safely.
  4. Remove the lower splash shield.
  5. Remove the air conditioner compressor drive belt.
  6. Remove the lower alternator cover plate bolts, loosen the alternator adjusting bolt and remove the drive belt.
  7. Remove the crankshaft pulley.
  8. Remove the coolant pump pulley.
  9. Remove the timing belt.
  10. Remove the oil level dipstick and guide tube.
  11. Remove the alternator adjusting bracket from the water pump.
  12. Remove the water pump rubber seals.
  13. Remove the water pump mounting bolts and nuts. Remove the water pump from the vehicle.
To install:
  1. Clean the gasket mating surfaces thoroughly.
  2. Check the water pump by hand for smooth operation. If the pump does not operate smoothly or is noisy, replace it.
  3. Install the pump using a new gasket. Tighten bolts to 115 inch lbs.. (13 Nm).
  4. Install new rubber seals.
  5. Install the upper alternator adjusting bracket and tighten bolt to 17 ft. lbs.. (23 Nm).
  6. Install the oil level dipstick and guide tube.
  7. Install the timing belt.
  8. Install the water pump pulley and leave the bolts hand tight.
  9. Install the crankshaft pulley.
  10. Install the water pump/alternator drive belt.
  11. Install the lower alternator cover plate and tighten bolts to 89 inch lbs.. (10 Nm).
  12. Install the air conditioner compressor drive belt by releasing the tensioner pulley and installing belt.
  13. Install the lower splash shield and lower vehicle.
  14. Tighten water pump pulley mounting bolts to 18 ft. lbs.. (24 Nm).
  15. Adjust the water pump drive belt tension and tighten alternator adjustment bolt to 17 ft. lbs.. (23 Nm).
  16. Install the air cleaner assembly.
  17. Refill the cooling system.
  18. Connect the negative battery cable.
  19. Start the engine and allow it to reach operating temperature. Check for leaks and refill cooling system as necessary.

Posted on Jul 18, 2008

  • 58 Answers

SOURCE: geo metro timing diagram

woot i feel your pain i had the same problem. go to autozone.com and go to thier vehicle repair.
enter your year make and model and find it. but please hear me on this one.. be carfule thier are like 2 timing references and one timing mark. USE THE DOT. pls i learned the hard way. lol use the dot on the cam sproket. good luck

Posted on Jan 29, 2009

bagorogi
  • 7 Answers

SOURCE: timing belt diagram and settings for a 1996 3.1tdi Troop

that one is easy my dear, go straight into the internet and download everything you need or visit nearby garages and request them.....

Posted on Jul 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 96 geo metro drove 15 miles and just died on me... Will not,start replaced dist. And dist cap and button,coil is getting power fuel is gettin to plugs, tried starter fluid but still nothin, fire is...


Depending on mileage, Geo's have timing belt and it should be changed every 60k, if you've done all that's mentioned I suspect timing belt is broken.

Mar 24, 2011 | 1996 Geo Metro

1 Answer

TIMING BELT


Sorry for the delay.
I am personally going back to answer your unanswered question. I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt/MARK(S) Diagrams that you will need, complete with Instructional and Directional Diagrams.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1996/make/geo/model/metro/1996_geo_metro_timing_belt_diagram_marks.htm

Jul 27, 2009 | 1996 Geo Metro

1 Answer

1994 Geo Metro Engine Rotates But Wont Start


check the timing belt it might have broken

Jul 09, 2009 | 1994 Geo Metro

1 Answer

Geo metro 97. Runs great for a day then wont start the next


Your timing belt is worn out. Some days it runs good because the cogs are lined up. The next time you start it, it maybe backfires just a touch, and it's out of time. Today, it's really out. Or maybe even broken.

May 20, 2009 | 1997 Geo Metro

1 Answer

I HAVE A1995 GEO METRO 1 LITER IN THE MORNING A HARD TIME TO START.I SOUNDS LIKE THE ENGINE IS GOING TO JUMP RIGHT OUT.


Your timing belt may have jumped ahead when it could have lost some teeth off of the belt. Check belt and replace if needed.

Mar 20, 2009 | 1991 Geo Metro

1 Answer

1996 Geo Metro 4 cylinder


http://www.fixya.com/cars/t591786-1997_geo_metro_starting_problem


look at this post, this may help, I am having the same problem and am going to try to find one of these parts.

Feb 24, 2009 | 1997 Geo Metro

1 Answer

92 Geo Metro won't start


Sounds like your timing belt has slipped or broken, bad news is it is a interference engine, talking rebuild if that is the problem.

Dec 26, 2008 | 1992 Geo Metro

1 Answer

Replacing broken timing belt on 92 GEO


a repair manual will show you the specs you need

Dec 06, 2008 | 1994 Geo Metro

Not finding what you are looking for?
1995 Geo Metro Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...