Question about 2000 Dodge Stratus

1 Answer

I have a Ford Focus 2006. It has come up with cos PO700 - Transmission control System On the dash it said Transmission malfunction D Was advised to take it to an Auto Electrician who found these codes when checking; PO700 - Transmission Control System PO4060 - Fuel Level Sensor But he is unable to find what these codes relate to. The car has a hesitation sometimes when changing gears and then "snaps" into gear Auto transmission specialist said it is not mechanical. Can anyone help me please or will I have to take to Ford dealer?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Dodge Master
  • 14,611 Answers

P0460 - Fuel Level Sensor A Circuit Description: The powertrain control module (PCM) monitors the fuel level input (FLI) circuit for electrical failure. The test fails when the signal moves outside the minimum or maximum allowable calibrated parameters for a specified fuel fill percentage in the fuel tank. Possible Causes:

  • Empty fuel tank
  • Fuel pump (FP) module concern
  • Incorrectly installed fuel gauge
  • Damaged instrument cluster
  • CASE GND circuit open
  • FLI shorted to VPWR
  • Overfilled fuel tank
  • Damaged fuel gauge
  • FLI circuit open
  • FLI circuit shorted to CASE GND or PWR GND
  • CSE GND shorted to VPWR
  • Damaged PCM
Diagnostic Aids: Monitor the FLI and FLI V PIDs in key ON, engine running. A concern is present if the FLI PID is at 25% fill and the FLI V PID is less than 0.90 volt with a non-matching fuel gauge or the FLI PID is at 75% fill and the FLI V PID is greater than 2.45 volts with a non-matching fuel gauge. Application Key On Engine Off Key On Engine Running Continuous Memory Ranger GO to Pinpoint Test HX . All others Refer to the Workshop Manual Section 413-01, Instrument Cluster for fuel level indicator diagnosis.
Your best bet would be to take it to a Ford dealer ,

P0700 Ford Transaxle Control System Malfunction
Possible causes Shorted or open circuit within Transmission Control Module (TCM) Faulty Transmission Control Module (TCM) What does this mean? Tech notes Since the P0700 is just and informative code, check the TCM for more codes to resolve the problem.

Read more:

Posted on Apr 19, 2017


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 8 Answers

SOURCE: 1997 Dodge Intrepid transmission slipping when warm

I was told to change my Transmission Control Module,located on the transmission . You can get it new for under $200 but, I was advised to get it from a junk yard it's alot cheaper and its easier. I hope this helps

Posted on May 07, 2009

  • 1 Answer

SOURCE: my 2006 dodge 2500 with 48RE Transmission is not

I had the same problem, Replace the govenor pressure sensor. There is a TSB out for this as well, I replaced bolth sensors that are mounted in the valve body of the trans. When I did mine I also adjusting the bands and now it is like a new trans. It was not hard and all the information can be found by searching. I think the sensors ran about $148 for bolth. You will need to remove the trans pan to complete this job if you are doing this. Hope this helps out.

Posted on Dec 22, 2009

  • 114 Answers

SOURCE: po700 trans error po732 gear 2 ratio incorrect

dodges do not have a strong transmission, I would be checking salvage yards for a replacement.

Posted on Jan 13, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why does a red light come up on the dash board saying a transmission malfunction on my focus 08

The light is on because something has malfunctioned in the transmission system, this can be a sensor or wiring or the transmission has a mechanical fault. The next step is to have a scanner hooked up and read the fault code that was set in the control modules memory when it turned on the warning light. This may require a trip to the local dealer.

Jan 06, 2017 | 2008 Ford Focus

1 Answer

I have a 2002 chrysler sebring shooting codes po700 po455 po442 po700 po841 po846 po732 gear2 inc ratio po731 inc ratio po733 pulled out solenoid and had a metal shaving on the magnetic end helpplease

P0700 Transmission Control System Malfunction P0445 Evaporative Emission Control System Purge Control Valve Circuit Shorted P0442 Evaporative Emission Control System leak Detected (small leak) P0841 Transmission Fluid Pressure Sensor/Switch A Circuit Range/Performance P0846 Transmission Fluid Pressure Sensor/Switch B Circuit Range/Performance P0732 Gear 2 Incorrect Ratio
Full list of the OBD2 DTC from P0700 to P0999

May 04, 2016 | Chrysler Cars & Trucks

1 Answer

What does code po700 mean

P0700 Transmission Control System Malfunction

Read more at:
Copyright ©

Apr 02, 2014 | 2006 Cadillac CTS

1 Answer

Po701 n po700 are comming up on my car

code po700 refers to transmission control system/mil -malfunction==causes ==wiring---TCM
code po701 refers to transmission control system -range/performance problem===causes wiring --tcm
As both show the TCM as a common point of the fault I would replace it.

Nov 08, 2013 | 2003 Saturn VUE

2 Answers

Have a2006 ram truck code PO700. what is that?

PO 700 -- all I have without service manuals for
your exact truck is a generic

Transmission Control System Malfunction

Having once owned a trans shop

My advice--stop using it until resolved

Aug 04, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

I got a U0103 and P0700 error code on my 2006 Jeep Grand Cherokee. Do I need to do anything about it?


Apr 20, 2010 | 2006 Jeep Grand Cherokee

1 Answer

I have cove po700 and po740 on my dodge durango

po700 transmission control system malfunction. and po740 torque converter clutch malfunction in solenoid/trans. relay circuit. hope this will help!!!!

Apr 16, 2010 | 2005 Dodge Durango

2 Answers

I havea code po700 what does it mean

That is a "transmission control system malfunction" code.

Jan 21, 2010 | 1998 Dodge Caravan

2 Answers

Code p0700

code po700 malfunction indicator lamp circuit malfunction tcm conditions. mil contoll circuit is shorted to ground .check the tcm for any codes in memory that are responsible for the request to turn on the mil lamp.tcm or trouble code malfunction has failed.

Nov 18, 2009 | 2002 Saturn VUE

1 Answer

Transmission problem

P0715 - Input/Turbine Speed Sensor Circuit Malfunction

P0700 - Transmission Control System Malfunction

Feb 14, 2009 | 1997 Dodge Stratus

Not finding what you are looking for?
2000 Dodge Stratus Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides