Question about 2001 Hyundai Accent

1 Answer

Why wont it start when you push start it has alt belt and has gas no ignition would that stop it from starting not geting gas to engin but all lines are holding gas so how do you bypass the fuel pump to engin to engage gas to injectors

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 57 Answers

When you turn the ignition on, it starts the fuel pump then sends fuel to the injectors. Since there is no ignition to engage the pump, it will 'starve' the vehicle of fuel. You might run a power source directly to your fuel pump but I'm NOT suggesting that because it would be wrong for me to tell you something like that... plus it could be dangerous. Remember, if you just happen to decide to do something like that, the fuel pump will not stop until you disconnect it (or it burns up). Be Careful!. Don't forget to vote if this helped you.

Posted on Apr 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Car won't start have new battery


IF you have replaced the battery and the car still wont start I would recommend you check the following and get back to me if it doesn't work.
1.Make sure the t-bar is pushed all the way forward so it regist that its in park.
2.I would recommend you give the starter motor a good tap if the car starts after this you will need a new starter motor

Jun 17, 2014 | 1998 Holden VT Commodore

1 Answer

Grinding noise from belt area


Could be the alternator going bad I only say that because there is a wire in the wiring system that is common to the ignition switch , the , alternator , and the transmission as well as the ECU, inhibitor switch, and the TCU. If the alt. bearing going out then I suppose it could cause a short and keep the circuit connected preventing it from shutting off. If you can't turn it off, try disconnecting the positive post of the battery, if it s the alt. was not putting out and I would check it then. At first I was going to say the ignition switch and the starter was staying engaged but you said it was coming from the belt area so that's why I'm leaning towards the alt. and not a tension or idler pulley . They going out would not keep the engine from stopping. If the engine did not stop when you disconnected the alt. then the priority at the moment is to stop the engine. You can do it by going to the panel that has the engine relay and fuses in it. Look to see which is the fuel relay and or fuse and pull it out. It may say fuel pump relay anything along those lines. this will shut your fuel pump off thus the engine will not continue to run and you can further investigate to see if the alt. is able to turn or if it's making a grinding noise when you turn it by hand. Of course you will have to take the belt loose to inspect this and while your at it you may as well check to make sure that none of the other pulleys or water pump is wearing/worn out also.

Apr 16, 2014 | 2008 Hyundai Sonata

1 Answer

My 2000 dodge caravan wont start and I have replaced the starter, starter relay, ignition switch, and the battery and also the crank shaft sensor.


There's no water in the cylinders because the engine still turns. Step number one is to unplug one of the spark plug wires, use a nail, screw, or an old spark plug, to see if it sparks keeping it about 1/4 inch from any metal part of the engine, while a friend cranks it. If there's spark, you have a fuel problem. If theres no spark, the #1 cause is a snapped timing belt(it happened to me). Remove one of two screws on the top plastic belt cover, open it just a little to peek if the belt is good or not. You should see the top of the camshafts and they will rotate when cranking. Theres info online on how to replace the belt, but dont try if you are not experienced. If the belt is ok, chances are its a pcm (computer) problem. The most common fuel failure is a faulty pump, located inside the gas tank. Disconnect the fuel line from the injectors bar(need an special plastic tool that cost $10) and plug the hose tightly with your finger, as a friend cranks the engine. The pressure should push the gas out. If your can contain it with your fingers, the pump is not working. But always check the spark first, is basic procedure in any car. Good luck!

Aug 03, 2012 | 2000 Dodge Grand Caravan

1 Answer

My 1993 legacy ran out of gas, and now wont start. I put 5 gal in it. Fuel pump works, filter is clean! Im stuck. HELP


there may be air in the system, try turning the key on to the ignition and push in the center pin to the schnader valve on the fuel line at the top of the engine (have a rag loosely placed over the line to catch fuel when it comes out (it will)-it should be a c=decent stream, you should then be able to start it. Turn the key to crank, do not press the gas petal.

Apr 18, 2011 | 1993 Subaru Legacy

2 Answers

My 97 saturn sl trys to start but wont it is geting gas, and spark but its seems to try to start and then stop and just crank over and over again


Could be one or more of many grips.
1. Fuel tank empty.
2. Battery discharged.
3. Battery terminal connections loose or corroded.
4. Leaking fuel injectior(s), faulty fuel pump, pressure regulator, etc.
5. Fuel not reaching fuel rail or TBI unit.
6. Ignition components damp or damaged.
7. Worn faulty or incorrectly gapped spark plugs.
8. Broken, loose or disconnected wiring in the starting circut.
9. Broken, loose or disconnected wires at the ignition coil or faulty coil. 10. Broken timing Chain.
11. Engine coolant temperature sensor defective.
12. Crankshaft postition sensor defective.

Hope this Helps!

Feb 06, 2010 | 1997 Saturn SL

1 Answer

I ran out of gas and put itright back in andnow it wont start itsounds like it wants to but it doesnt


there should be a bleeder in the engine compartment on the fuel hose to your injector rail try turning key on and pushing the bleeder to let out air in the line . hope that helps . if gas comes out it's pressurized and stop pushing the bleeder

Nov 19, 2009 | 1999 Dodge Intrepid

1 Answer

My 2003 crysler sebring stalled and want start back I geting the camshift sensor code I replaced it and car still wont start and still geting the code Would the timeing belt casue this


Yes a timing belt could cause this. Ususally if the timing belt breaks/slips the engine will have a different sound while cranking it over to try to start it. Does it sound different? Also, if possable remove the cam position senser and look at the tone wheel that the senser reads and have someone crank the engine to see if the tone wheel turns, if not the timing belt is most likely the problem. I have seen a few tone wheels have problems but it is not common. What engine do you have?

Jun 05, 2009 | 2003 Dodge Caravan

Not finding what you are looking for?
2001 Hyundai Accent Logo

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...