Question about 1995 Honda Accord

1 Answer

I have no brakes i have changed the pads ,caliper and master still no brakes

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 8,404 Answers

Did you pump up the pedal? Is there air in the line?

Posted on Apr 23, 2010

Testimonial: "thank you we pumped the pedel AGAIN and now it works we have been working on this all day"

  • A Miller Apr 24, 2010

    It takes several pumps to get the slave units filled ... thanks for the 4 thumbs up and thanks for your interest in FixYa.com

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Power steering is winding and drakes are sticking


There are at least 2 items that will cause your problem. The first is when you changed the pads you place the caliper in a different place on the support pins that the caliper slides on to centralise the brakes on the rotor. These mounting pins are prone to rusting up and actually keeps one pad on the rotor as the caliper cannot centralise during brake application. The second is a problem that occurs when the brake fluid is pushed back into the master cylinder reservoir from pushing the piston back into the caliper. Muck in the lines is pushed back into the compensating ports in the Master cylinder causing the brakes to drag and build up pressure from the heat generated by having the brakes on. Try flushing out the brake system using metholated spirits or replace the master cylinder

Dec 01, 2013 | 2004 GMC Savana

2 Answers

2001 Montero brakes. R&R rear rotor, pads & calipers but the brake pedal travel is still very slow to "reset". I am certain my front's need new rotors, pads and possibly calipers due to the...


Disk brakes are automatically self adjusting. If you have too much travel in the pedal, bleed the brakes. Let us know if you need the procedure.

Jul 02, 2017 | 2001 Mitsubishi Montero

1 Answer

How do you replace the front and rear brakes in a 2003 pontiac Grand Prix


Removal & Installation Front To Remove:
  1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
  2. Remove the tire and wheel assembly.
  3. Install 2 wheel nuts to secure the rotor on the hub.
  4. Remove the bottom brake caliper pin bolt.
  5. Pivot the brake caliper body upward and secure out of the way. Do NOT disconnect the hydraulic brake flexible hose from the caliper.
  6. Compress the piston back into the bore using a C-clamp. Figure of brake assembly with caliper raised showing brake pads in mounting bracket gmpc_l4.gif

  7. Remove the inboard and outboard brake pads from the brake caliper bracket.
To Install:
  1. Install the brake pad retainers and both brake pads into the caliper bracket.
  2. Pivot the brake caliper down over the brake pads and into the brake caliper bracket. Insert the lower brake caliper pin bolt and torque bolt to 70 ft-lb. (95 Nm).
  3. Reinstall the tire and wheel assembly.
  4. Lower the vehicle.
  5. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
  6. Check the master cylinder level and add fluid as necessary.
Rear To Remove:
Rear disc pads R&I gm-09-00-492.gif

  1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
  2. Remove the tire and wheel assembly.
  3. Install 2 wheel nuts to secure the rotor on the hub.
  4. Remove the upper caliper mounting bolt.
  5. Pivot the caliper down to access the pads.
  6. Remove the inboard and outboard pads from the caliper bracket.
  7. Remove the brake pad clips from the caliper bracket.
  8. Compress the piston back into the bore using a C-clamp and the old inner pad.
To Install:
  1. Install new brake clips in the caliper bracket.
  2. Install the inboard and outboard pads in the caliper bracket.
  3. Pivot the caliper up over the pads.
  4. Reinstall the upper mounting bolt and tighten to 32 ft. lbs. (44 Nm).
  5. Remove the 2 wheel nuts securing the rotor.
  6. Reinstall the tire and wheel assembly.
  7. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
  8. Check the master cylinder level and add fluid as necessary.
prev.gif next.gif

Aug 26, 2010 | 2003 Pontiac Grand Prix

1 Answer

How to change front brake pads on 2003 Chevy Suburban


Disc Brake Pads for Suburban 1500 Removal & Installation Front To Remove:
Front caliper mounting bracket 93086g95.gif

  1. Remove the cover on the master cylinder and siphon out 2/3 of the fluid. This step prevents spilling fluid when the piston is pushed back into the caliper bore.
  2. Raise and support the vehicle safely.
  3. Remove the wheel and tire assembly.
  4. Compress the brake piston back into its bore using a C-clamp.
  5. Remove the 2 caliper mounting bolts. Lift the caliper off the rotor.
  6. Remove the inboard and outboard pad.
  7. Remove and discard the anti-rattle clips.
To Install:
Caliper bracket sleeves 93086g97.gif

  1. Thoroughly inspect, clean and lubricate all caliper slide points, bolts and hardware.
  2. Install new anti-rattle clips.
  3. Position the inboard and outboard pads into the support bracket
  4. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
  5. Install the caliper mounting bolts through the sleeves in the inboard caliper ears and into the mounting bracket.
  6. Tighten the mounting bolts to: 80 lb. ft, (110 Nm).
  7. Install the tire and wheel assembly. Lower the vehicle.
  8. Add fluid to the master cylinder reservoirs so they are 1/4 in. (6.35mm) from the top.
  9. Test the brake pedal by pumping it to obtain a hard pedal. Check the fluid level and add fluid as necessary.
Rear To Remove:
  1. Remove 2/3 of the brake fluid from the master cylinder.
  2. Raise and safely support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Remove the brake caliper mounting bolts. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
  5. Remove the brake pads from the caliper mounting bracket.
  6. Remove and discard the anti-rattle clips.
Rear brake caliper 93086g96.gif

To Install:
  1. Install new anti-rattle clips.
  2. Position the brake pads to the caliper mounting bracket.
  3. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
  4. Install NEW caliper mounting bolts. Tighten to: 30 lb. ft, (40 Nm).
  5. Install the wheel and tire assembly.
  6. Lower the vehicle.
  7. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly to seat the brake pads. Burnish the brakes as needed.
prev.gif next.gif

Jul 05, 2010 | 2004 Chevrolet Suburban

1 Answer

Brake pad replacement 2004 audi a4 and rotor how do i do and what tools are neccessary?


YOU NEED REMOVE A LITTLE BRAKE FLUID FROM MASTER CYLINDER.THEN YOU RAISE VECHICLE SAFELY.SUPPORT IT WITH JACK STAND.MAKE SURE VECHICLE IS ON LEVEL SOLID GROUND.REMOVE TIRE OR WHEEL.THEN YOU NEED A LARGE C - CLAMP.PLACE C - CLAMP OVER BRAKE CALIPER AND BRAKE SHOE BACKING.TIGHTEN C - CLAMP JUST ENOUGH PUSH CALIPER PISTON BACK IN CYLINDER BORE TO REMOVE CALIPERS FROM ROTORS.TO REMOVE BRAKE CALIPER YOU NEED 2 OPEN AND BOX END WRENCHES ONE TO HOLD CALIPER SLIDE PINS AND THE OTHER WRENCH FOR LOOSEN CALIPER BOLTS.THEN YOU REMOVE CALIPER AND REPLACE FRONT BRAKE SHOES.IF YOU NEED TO REMOVE BRAKE ROTORS JUST REMOVE THE BRAKE CALIPER CARRIER SUPPORT BOLTS THE REMOVE THE BRAKE CALIPER CARRIER SUPPORT THEN REMOVE ROTOR.YOU NEED TO REPLACE BOLTS WITH NEWS AND USE LOCK TIGHT.THEN YOU PUT IN NEW BRAKE PADS IN CALIPER PUT CALIPER BACK ON SUPPORT CARRIER.REPLACE WITH NEW BOLTS USE LOCK TIGHT THEN TORQUE BOLTS TO 26 FT LBS.MAKE SURE MASTER CYLINDER COVER IN PLACE.WHEN YOU FINISH REPLACING BOTH FRONT BRAKE PADS PUMP BRAKE PEDAL TO SEAT BRAKE SHOES AGAINST BRAKE ROTORS SO YOU WILL HAVE FIRM BRAKES WHEN YOU APPLY THEM. THEN CHECK YOUR BRAKE FLUID LEVEL IN MASTER CYLINDER MAKE SURE ITS NOT LOW. MAKE SURE YOU HAVE FIRM BRAKES BEFORE DRIVING.IF YOU HAVE ANY PROBLEMS CHANGING FRONT BRAKE PADS YOU CAN GO TO ANY AUTO PARTS STORE AND BUY A HAYNES REPAIR MANUAL.

Jun 16, 2010 | 2004 Audi A4

1 Answer

Need help changing brake pads and routers on 2003


Remove brake fluid from the master cylinder brake fluid reservoir until the reservoir is approximately 1/2 full. Discard the removed fluid.
  1. Raise and safely support the front of the vehicle. Remove the front wheels.
    1. Remove or disconnect the following:
    2. Front brake caliper guide pin bolts
    • Brake caliper by slowly sliding it up and off the adapter and brake rotor. Support the caliper out of the way with a strong piece of wire. Do not let the caliper hang by the brake hose or damage to the brake hose will result.
    1. If necessary, compress the caliper piston into the bore using a C-clamp. Insert a suitable piece of wood between the C-clamp and caliper piston to protect the piston.
    2. Outboard disc brake pad from the caliper by prying the brake pad retaining clip over the raised area on the caliper. Slide the brake pad down and off the caliper.
    • Inboard disc brake pad from the caliper by pulling the brake pad away from the caliper piston until the retaining clip on the pad is free from the caliper piston cavity
  • To install:
    1. Be sure the caliper piston has been completely retracted into the piston bore of the caliper assembly. This is required when installing the brake caliper equipped with new brake pads.
    2. If equipped, remove the protective paper from the noise suppression gaskets on the new disc brake pads.
    3. Install or connect the following:
      • New inboard disc brake pad into the caliper piston by pressing the pad firmly into the cavity of the caliper piston. Be sure the new inboard brake pad is seated squarely against the face of the brake caliper piston.
      • Outboard disc brake pad by sliding it onto the caliper assembly
      • Brake caliper assembly over the brake rotor and onto the steering knuckle adapter
      • Caliper guide pin bolts and torque to: 35 ft. lbs. (47 Nm) on 2002–04 models or 26 ft. lbs. (35 Nm) on 2005 models
      • Front. Apply the brake pedal several times until a firm pedal is obtained.
    4. Check the fluid level in the master cylinder and add fluid as necessary. Road-test the vehicle.

    For the rotors:

    1. Remove brake fluid from the master cylinder brake fluid reservoir until the reservoir is approximately 1/2 full. Discard the removed fluid.
    2. Raise and safely support the front of the vehicle. Remove the front wheels.
    1. Remove or disconnect the following:
    2. Front brake caliper guide pin bolts
    • Brake caliper by slowly sliding it up and off the adapter and brake rotor. Support the caliper out of the way with a strong piece of wire. Do not let the caliper hang by the brake hose or damage to the brake hose will result.
    1. If necessary, compress the caliper piston into the bore using a C-clamp. Insert a suitable piece of wood between the C-clamp and caliper piston to protect the piston.
    2. Outboard disc brake pad from the caliper by prying the brake pad retaining clip over the raised area on the caliper. Slide the brake pad down and off the caliper.
    • Inboard disc brake pad from the caliper by pulling the brake pad away from the caliper piston until the retaining clip on the pad is free from the caliper piston cavity
  • To install:
    1. Be sure the caliper piston has been completely retracted into the piston bore of the caliper assembly. This is required when installing the brake caliper equipped with new brake pads.
    2. If equipped, remove the protective paper from the noise suppression gaskets on the new disc brake pads.
    3. Install or connect the following:
      • New inboard disc brake pad into the caliper piston by pressing the pad firmly into the cavity of the caliper piston. Be sure the new inboard brake pad is seated squarely against the face of the brake caliper piston.
      • Outboard disc brake pad by sliding it onto the caliper assembly
      • Brake caliper assembly over the brake rotor and onto the steering knuckle adapter
      • Caliper guide pin bolts and torque to: 35 ft. lbs. (47 Nm) on 2002–04 models or 26 ft. lbs. (35 Nm) on 2005 models
      • Front. Apply the brake pedal several times until a firm pedal is obtained.
    4. Check the fluid level in the master cylinder and add fluid as necessary. Road-test the vehicle.

    May 28, 2010 | 2003 Chrysler Town & Country

    1 Answer

    How do i change back brakes on 2000 olds bravada same as front


    If the rear is disc...here ya go!

    Removal & Installation
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Remove or disconnect the following:
      • 2/3 of the brake fluid from the master cylinder
      • Wheels
    3. Place a C-clamp around the outer pad and caliper; tighten the C-clamp until the piston is fully compressed in the caliper.
      • Top caliper retainer, and rotate caliper away from rotor
      • Inboard pad and retaining spring from the caliper
      • Outboard pad from the caliper
    To install:
    1. Clean and lubricate the sleeves and bushing with silicone lubricant
    2. Install or connect the following:
      • Sleeves and bushings into the caliper
      • Clip the retaining spring onto the inboard pad and install the pad in the caliper
      • Outboard pad into the caliper
      • Caliper in position over the rotor and install the mounting bolts
      • Wheel and tire assemblies
    3. Refill the master cylinder and pump pedal to attain full brake pedal before Road-testing the vehicle.

    May 11, 2010 | 2000 Oldsmobile Bravada

    1 Answer

    How do i change front brake pad on this car merecy sable 1989 -99


    Remove the wheel, remove the 2 bolts holding on the caliper to the caliper carrier. You will need a large C-Clamp or a cailper piston tool. Place an old brake pad against the piston in the caliper and use the C-Clamp to push the brake pad against the piston to collapses the piston into the caliper. Also open the master cylinder cap and place a towel around the area to catch any brake fluid that would come out of the master cylinder as you collapes the piston, this is normal, but doesn't always happen, depending on the level of fluid in the master cylinder. Install the new pads and reinstall the caliper and wheel. Make sure you pump the brake pedal a few times before you take off, to get the pads against the rotor.

    Mar 16, 2010 | 1999 Mercury Sable

    1 Answer

    Silverado 1500 Z71 off road, 5.3L. Details on fr


    This is for the front: Removal & Installation
    1. Remove 2/3 of the brake fluid from the master cylinder.
    2. Remove or disconnect the following:
      • Wheel
      • Caliper. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
      • Caliper mounting bracket bolts
      • Caliper mounting bracket from the steering knuckle assembly
      • Brake pads from the caliper mounting bracket
      • Clips from the inside ends of the caliper mounting bracket and discard
    To install:
    1. Install or connect the following:
      • Clips to the inside ends of the caliper mounting bracket
      • Brake pads to the caliper mounting bracket
      • Inner pad (1 wear indicator)
      • Outer pad (2 wear indicators)
      • Caliper mounting bracket to the steering knuckle assembly
    2. Perform the following procedure before installing the caliper mounting bracket bolts:
      • Remove all traces of the original adhesive patch.
      • Clean the threads of the bolt with brake parts cleaner or the equivalent and allow to dry.
      • Apply red Loctite®272 to the threads of the bolt.
    3. Install or connect the following:
      • Caliper mounting bracket bolts to the steering knuckle. Tighten the caliper guide pin bolts to 74 ft. lbs. (100 Nm) on 15 series or 80 ft. lbs. (108 Nm) on 25/35 series.
      • Caliper
      • Tire and wheel assembly
    4. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly in order to seat the brake pads. Burnish the brakes as needed.

    Oct 12, 2009 | 2003 Chevrolet Silverado 1500

    3 Answers

    How do i change the pads and rotors on my 2002 trailblazer ls?



    If you Need Pics/ Illistrations Email @rejakwilson@aol.com


    Brake Pads Replacement - Front

    Removal Procedure

    Caution: Refer to Brake Dust Caution in Service Precautions.

    1. Inspect the brake fluid level in the brake master cylinder reservoir.
    2. If the brake fluid is midway between the maximum-full point and the minimum allowable level, no brake fluid needs to be removed from the reservoir before proceeding.
    3. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, remove the brake fluid with appropriate tool to the midway point before proceeding.
    4. Raise the vehicle. Refer to Vehicle Lifting.
    5. Remove the tire and wheel assembly.

    1. Compress the front brake caliper piston.
    6.1. Install a large C-clamp over the top of the brake caliper housing and against the back of the outboard brake pad. 6.2. Slowly tighten the C-clamp until the piston pushes into the brake caliper enough to slide the brake caliper off the rotor. 6.3. Remove the C-clamp from the brake caliper.
    1. Remove the lower mounting bolt from the slide pin.
    2. Rotate the brake caliper upward until it stops.
    3. Remove the outboard brake pad.
    4. Remove the inboard brake pad.
    5. Remove the brake pad retaining clips from the brake caliper mounting bracket.
    6. Remove the brake pad retaining clip from the brake caliper.
    7. Remove all foreign material from the brake caliper using denatured alcohol.
    Installation Procedure

    Important: When installing new brake pads, DO NOT reuse the old retaining clips for the brake pad. Use only NEW brake pad retaining clips.


    1. Install the brake pad retaining clips to the brake caliper mounting bracket.
    2. Install the brake pad retaining clip to the brake caliper.
    3. Ensure that the brake pad retaining clip in the brake caliper is properly seated.
    4. Install the inboard brake pad.
    5. Install the outboard brake pad.
    6. Rotate the brake caliper down into position.


    Notice: Refer to Fastener Notice in Service Precautions.

    1. Install the lower brake caliper mounting bolt.
      • Tighten the brake caliper mounting bolt to 51 Nm (38 ft. lbs.) .
    1. Install the tire and wheel assembly.
    2. Lower the vehicle. Refer to Vehicle Lifting.
    3. Fill the brake master cylinder reservoir. Caution: Refer to Firm Brake Pedal Caution in Service Precautions.
    4. Pump the brake pedal slowly and firmly to seat the brake pads.
    5. Burnish the new brake pads.



    blnk_spc.gif

    Jul 24, 2009 | 2004 Chevrolet TrailBlazer

    Not finding what you are looking for?
    1995 Honda Accord Logo

    Related Topics:

    76 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    yadayada
    yadayada

    Level 3 Expert

    75117 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7772 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...