Question about 2001 Dodge Durango

1 Answer

How hard is it to replace the MAP sensor on a 2001 dodge durango?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 2,984 Answers

VERY SIMPLE!!!!!

4.7L The MAP sensor is located on the front of the intake manifold. An O-ring seals the sensor to the intake manifold.

  1. Disconnect electrical connector at sensor.
  2. Clean area around MAP sensor.
  3. Remove 2 sensor mounting bolts.
  4. Remove MAP sensor from intake manifold.
To Install:
  1. Clean MAP sensor mounting hole at intake manifold.
  2. Check MAP sensor O-ring seal for cuts or tears.
  3. Position sensor into manifold.
  4. Install MAP sensor mounting bolts (screws). Tighten screws to 3 Nm (25 inch lbs..) torque.
  5. Connect electrical connector.

Posted on Apr 23, 2010

Testimonial: "Awesome....sounds easy enough to do it on my own and same some cash...Thanks!"

  • GItsMe Apr 19, 2011

    What if the bolt is stripped? Any suggestions?

  • Greg Bernett
    Greg Bernett Apr 19, 2011

    They make a small spring-type insert called a "helicoil". If you cannot find one of those, you can go the next sive up and re-tap the hole with a tap and die set. Basically with this tool, you are making a new hole with a new bolt.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Dodge Durango 5.2L V8 starts but won't run


By run - do you mean it dies when you put it in gear? Or that it just bogs down when you attempt to accelerate or drive away?
..
A plugged Catalytic converter will cause this. So will a Bad MAP or MAS (Mas Air ) sensor. So will a bad TPS (Throttle Position) sensor.
....
Need more input to answer more precisely.

Jul 25, 2012 | 2001 Dodge Durango

1 Answer

Does a 2002 dodge Durango with a 4.7L engine have a mass air flow sensor and if so where is it ?


No mass air flow sensor but if you are talking bout MAP-Manifold Absolute Pressure Sensor
The write up is right here

http://www.ehow.com/how_7974375_replace-1999-durangos-map-sensor.html


Hope this helps

Positive Feedback ALWAYS Appreciated :)

Mar 06, 2011 | 2002 Dodge Durango

1 Answer

Hello, I'm currently living on Guam and cannot find a mechanic who can correct my 2001 Dodge Durango (with error code P 0108) probelm. It will occassionally idle rough and stall. At times the "check...


P0108 = MAP sensor circuit high voltage

The MAP sensor communicates the barometric pressure inside the intake manifold to the ecm.
This code can indicate either a fault in the MAP (manifold absolute pressure) sensor, or a possible vacuum leak, either from a hose or the intake gasket.

It could be the connector on this sensor isn't making good contact. I would check the connector before you replace the sensor. It more than likely needs a new MAP sensor.

Jan 20, 2011 | 2001 Dodge Durango

1 Answer

REPLACED FUEL PUMP UNIT CRANKS TAKES ABOUT 10


upper 02 sensor run on a loop till the engine gets warm then it reads the sensor get you back on the road fast it will work better if the engine is warm when you take out the o2 sensor

May 04, 2010 | 2001 Dodge Durango

1 Answer

1999 dodge durango-Heat does not work unless it's 60 degrees outside what could be wrong?


Try replacing the MAP (Manifold Absolute Pressure) sensor first. You can try disconnecting the MAP sensor and see if the engine starts, if it does, then replace the MAP sensor. Good luck and hope this helps, check the wire harness to the MAP sensor.
A Manifold Absolute Pressure sensor is a input sensor that measures the change in engine manifold pressures. Not to be confused with a baro (barometric sensor) that measures the altitude in which the vehicle is being operated in. And also not to be confused with a MAF (Mass Airflow Sensor)that measures air flow and density of the air for the computer to make fuel adjustments.
The MAP is an electronic device that is composed of an empty chamber with a flexible diaphragm in the center. One side of the chamber would be exposed to atmospheric pressure while the other is connected to the engine vacuum. This difference in pressure causes the diaphragm to bend one way or the other. The degree of deflection is measured by the strain gage and that data is relayed to the ecm. Depending on how much or little vacuum there is in the engine depends on the operating conditions and thus the ecm can know how hard the engine is running and therefore supply the correct amount of fuel to supply and maybe when to most efficiently ignite the spark.

Nov 03, 2009 | 1999 Dodge Durango

1 Answer

Getting a code p0121on my dodge durango 2001


Trouble code P0121 means: Throttle Position Sensor Voltage Does Not Agree With Map Sensor. You can replace the TPS for @ $30 from Autozone. Please vote appropriately and leave a comment. I hope this helps and Good luck.

Oct 29, 2009 | 2001 Dodge Durango

1 Answer

What Happens When a Map Sensor Goes Bad on 2001 dodge durango?


Manifold Absolute Pressure sensor controls fuel delivery and ignition timing, the pressure in the intake manifold will vary due to stress or work load, the MAP sensor monitors this, reporting to the computer. Good luck.

Jul 12, 2009 | 2001 Dodge Durango

2 Answers

My check engine light is on. The code is P0121


I believe all the Mopar OBDC codes are the same. A list of the 2001 codes were posted on a PT Cruiser site here: 2001 Chrysler codes

Your error says the throttle position sensor and MAP sensor disagree with each other

Jun 22, 2009 | 2001 Dodge Durango

1 Answer

2001 dodge durango v8 4.7


If the speedometer still works,then no you don't need the speed sensor.The problem sounds more like the catalytic converter Which was a recall item on most Durangos and Dakotas for that year should be replaced for free at the dealer.

Jan 04, 2009 | 2001 Dodge Durango

Not finding what you are looking for?
2001 Dodge Durango Logo

1,100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...