Question about Chevrolet C3500

2 Answers

2003 Diesel 6.6,chev.No Power at pump,have ecm referance 12.5 volts,have battery power at other termanal at relay,have ground at other termanal (blk) have continuity on both wires going from the fuse box to the pump .If I jump at box from relay terminal (hot at all times)to blk wire (ground)the pump runs.Could it be the ecm,does it not control the grounds.Dan

Posted by on

  • dbonnett122 Apr 23, 2010

    i HAVE A SCAN TOOL,IT WILL NOT SHOW YOU THIS PROBLEM

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,489 Answers

Email me and I will get a schematic you can work with but yes you are right. The ecm does control the lift pump relay. iambanshee74@yahoo.com

Posted on Apr 23, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,865 Answers

Hello Dan. If you have an AAMCO repair shop nearby go there because they offer a free computer scan. This scan will pinpoint your problem area. Some auto parts stores also offer a free scan now. Dealerships generally charge. Sooooooo ask around before you agree to a costly scan unknowingly. Joe

Posted on Apr 23, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced bad fuel pump. Still will not start. Only 6 volts at the pump relay. Bypassing the relay indicated pump is working and plenty of pressure. Checked all the fuses all are good. Any ideas?


Year make and model ?
You should have two hot circuits to the relay. One is for the pump and the other is for the coil of the relay. Usually power comes from the key switch.

Jan 01, 2016 | Cars & Trucks

1 Answer

Low beams dont work and only one high beam works


Do you know how to do voltage drop testing ? Leave the blubs in there sockets turn the low beams on , measure voltage on the power side , LH low beam yellow with black stripe an for the RH low beam dark blue wire . If you have battery voltage there, power side is good . Then check ground side both are yellow wires , test with lights on . if you see 6 volts , 12 volts .anything more then .03 millivolts you have a ground side problem . The lights ground through the light switch .
Low Beam
Voltage to the headlamp switch is available at all times from the HDLP SW fuse 7 through CKT 1940 (ORN). When the headlamp switch is turned to the HDLP position, the headlamp power relay coil is energized through CKT 352 (WHT). A signal is also sent to the body control module (BCM) that the headlamp switch is ON. When the headlamp switch is in the AUTO or PARK position, the ambient light sensor (located in the right speaker grill) senses either daylight or darkness and sends the signal to the BCM. When the Ambient Light Sensor detects a dark condition, the BCM produces a signal that will energize the headlamp power relay through CKT 352. The relay coil is grounded through terminal F7 connector 2 of the underhood fuse block to CKT 350 (BLK) to G102. When the headlamp power relay is energized the relay supplies power to the LT HDLP and RT HDLP fuses. The RH low beam headlamp receives current through CKT 198 (DK BLU) from the RT HDLP fuse. The LH low beam headlamp receives current through CKT 712 (YEL/BLK) from the LT HDLP fuse. Both headlamp low beam bulbs are grounded by CKT 524 (PPL) through the underhood fuse block to the multifunction switch (low position) contacts through CKT 10 (YEL) to the headlamp grounding relay in the body relay block through the normally closed contacts to CKT 1850 (BLK) to G200.

Oct 14, 2015 | 1999 GMC Sonoma

1 Answer

Where can i get an 01 silhouette pcm pinout


PCM pinout diagrams
2001 silverado (Thanks Banker099)

Try this link for page below


wol_error.gifThis image has been resized. Click this bar to view the full image. The original image is sized 799x247 and weights 17KB.connectorc1pcm2001.gif

Powertrain Control Module (PCM) C1 (BLU)



Connector Part Information
• PCM Connector C1 Assembly 12191489

• TPA (BLU) 12176408

• Connector Cover 12191108

Pin
Wire Color
Circuit No.
Function

1
BLK/WHT
451
Ground

2
LT GRN
1867
12 Volt Reference

3
PNK/BLK
1746
Fuel Injector 3 Control

4
LT GRN/BLK
1745
Fuel Injector 2 Control

5-10
--
--
Not Used

11
LT BLU
1876
Knock Sensor 2 Signal

12
DK BLU/WHT
1869
CKP Sensor Signal

13
ORN/BLK
463
Requested Torque Signal

14
ORN/BLK
1061
UART Serial Data [Secondary]

15
DRK BLU/WHT
774
UART Serial Data [Tertiary]

16
--
--
Not Used

17
DK BLU
1225
Transmission Fluid Pressure Switch Signal B

18
RED
1226
Transmission Fluid Pressure Switch Signal C

19
PNK
439
Ignition 1 Voltage

20
ORN
440
Battery Positive Voltage

21
YEL
1868
Low Reference

22
--
--
Not Used

23
PPL
719
Low Reference

24
--
--
Not Used

25
TAN
1671
HO2S Low Signal [- Bank 2 Sensor 1]

25
TAN
413
HO2S Low Reference (Denso Sensors) HO2S Low Signal (Delphi Sensors)

26
TAN
1667
HO2S Low Signal [- Bank 2 Sensor 2]

26
TAN
413
HO2S Low Reference (Denso Sensors) HO2S Low Signal (Delphi Sensors)

27
--
--
Not Used

28
TAN/WHT
1669
HO2S Low Signal [- Bank 1 Sensor 2]

28
TAN
413
HO2S Low Reference (Denso Sensors) HO2S Low Signal (Delphi Sensors)

29
TAN/WHT
1653
HO2S Low Signal [- Bank 1 Sensor 1]

29
TAN
413
HO2S Low Reference (Denso Sensors) HO2S Low Signal (Delphi Sensors)

30
LT GRN
1478
Coolant Level Switch Signal

31
--
--
Not Used

32
BLK/WHT
771
Transmission Range Switch Signal A

33
PPL
420
TCC Brake Switch Signal

34
WHT
776
Transmission Range Switch Signal P

35
GRA
48
CPP Switch Signal

36
BLK
1744
Injector 1 Control

37
YEL/BLK
846
Injector 6 Control

38
PNK/WHT
1101
Damping Lift/Dive Signal

39
--
--
Not Used

40
BLK/WHT
451
Ground

41
BLK
407
Low Reference

41
GRA
720
Low Reference (w/o Delphi HO2S)

42
--
--
Not Used

43
RED/BLK
877
Fuel Injector 7 Control

44
LT BLU/BLK
844
Fuel Injector 4 Control

45
GRA
474
5 Volt Reference (FTP Sensor)

46
GRY
474
5 Volt Reference (TPS Sensor)

47
GRY
597
5 Volt Reference (MAP Sensor)

48
GRA
596
5 Volt Reference (EGR Sensor)

49 50
--
--
Not Used

51
DK BLU
496
KS [1] Signal

52
--
--
Not Used

53
BLK
470
Low Reference

54
BLK
452
Low Reference

55
BRN
1456
EGR Valve Position Signal

56
--
--
Not Used

57
ORN
440
Battery Positive Voltage

58
DK GRN
1049
ECM/PCM/VCM Class 2 Serial Data

59
YEL
710
Class 2 Serial Data

60
ORN/BLK
469
Low Reference

61
PNK/BLK
632
Low Reference

62
--
--
Not Used

63
GRA
720
Low Reference

63
TAN
413
HO2S Low Reference (Denso Sensors) HO2S Low Signal (Delphi Sensors)

64
--
--
Not Used

65
PPL
1670
HO2S High Signal [- Bank 2 Sensor 2]

66
PPL
1666
HO2S High Signal [- Bank 2 Sensor 1]

67
--
--
Not Used

68
PPL/WHT
1668
HO2S High Signal [- Bank 1 Sensor 2]

69
PPL/WHT
1665
HO2S High Signal [- Bank 1 Sensor 1]

70
BRN
1174
Oil Level Switch Signal

71
--
--
Not Used

72
YEL
772
Transmission Range Switch Signal B

73
BRN/WHT
633
CMP Sensor Signal

74
YEL
410
ECT Sensor Signal

75
PNK
1020
Off/Run/Crank Voltage

76
BLK/WHT
845
Fuel Injector 5 Control

77
DK BLU/WHT
878
Fuel Injector 8 Control

78
--
--
Not Used

79
WHT
687
3-2 Shift Solenoid Valve Control

80
ORN/BLK
510
Low Reference
wol_error.gifThis image has been resized. Click this bar to view the full image. The original image is sized 799x247 and weights 17KB.connectorc2pcm2001.gif

May 23, 2014 | 2001 Oldsmobile Silhouette

1 Answer

2003 s10 blazer cranks no start . when I was trying to test the crank sensor signal wire I found 10 volts present with ignition on not cranking. the ground wire has 12.5 with the key off and 12.21 volts...


Will a scan tool communicate with it or on the screen does it say NO COMM ! That's how you test a PCM/ECM . If no comm ,check power an ground's ,that's it .
Why were you messing with the crank sensor ? If the fuel pump primes for two seconds there is nothing wrong with it . When cranking the engine the PCM/ECM will only energize the fuel pump if it see's an input from the crank sensor ! You will not see 12 volts on the crank sensor signal return wire ! Crankshaft Position (CKP) Sensor
The CKP sensor is a three wire sensor based on the magneto resistive principle. A magneto resistive sensor uses two magnetic pickups between a permanent magnet. As an element such as a reluctor wheel passes the magnets the resulting change in the magnetic field is used by the sensor electronics to produce a digital output pulse. The PCM supplies a 12-volt, low reference, and signal circuit to the CKP sensor. The sensor returns a digital ON/OFF pulse 3 times per crankshaft revolution for the V6 engine, 4 times for the V8 engine. The CKP sensor reads the crankshaft mounted reluctor wheel to identify pairs of cylinders at top dead center (TDC).

May 20, 2017 | 2003 Chevrolet Blazer

1 Answer

Replaced fuel pump now no power to pump


If you unplug the connector for the pump, you should have battery voltage on the pump circuit from the relay for 3 seconds. You would have 5 or 6 volts for the gauge sending unit.
You should be able to jumper the pump relay and get 12 volts at the pump connector.

Oct 16, 2012 | 1996 Chevrolet S-10 Pickup

2 Answers

2000 Kia Sportage ECM ECU Bad?


Check the pcm ground pins to make sure they are grounded. 6, 28, 34, and 55.


0996b43f80250ba5-l15fcbeisfileg1jtnhunp3x-3-0.gif

Jul 23, 2017 | 2000 Kia Sportage

2 Answers

2002 NISSAN SENTRA DIED WHILE DRIVING KEY ON ENGINE OFF .NO ENGINE LITE .NEITHER ENGINE OR NATS PROGRAM WILL PULL UP WITH CONSULT 2.REPLACE ECM NO CHANGE .POWER TO RELAY 1 AND 2 6 AND 7 ----- 3 AND 5 NONE...


Hello! There isn't power to ECM pins 109 and 111 because the ECM relay is not pulling...Pins 1 and 3 (White/Black wire) are tied together in the harness and should not show a change in symptom if jumped together...Also, Pins 1 and 3 are fed battery from fuse # 36 (15A hot at all times) and both pins must read +12 volts...Pin 2 of the relay coil is the pulling ground from the ECM...Reading across pins 1 and 2 with the key in the ON position should not read +12 volts...If it does the relay coil is open...With the key on the relay would show a voltage drop across the coil...Check pins 1 and 3...must be tied together and have +12 volts from fuse # 36 (15A hot at all times)...Replace ECM relay...See photo...............Guru....Saailer...

saailer_105.jpg

STANDARD MOTOR PRODUCTS Part # RY412 Cost

Jan 26, 2011 | Nissan Se R Cars & Trucks

1 Answer

Fuel pump not coming on,installed new one, white plug that has a yellow wire has 5 volts and ground is ok the 2 wires in the center shows 0


The plug you are referring to is probably the fuel tank pressure sender not the fuel pump. It would be plugged into a black sensor about 2 inches long pushed into a rubber grommet on the fuel bung. The fuel pump connector would have more that 2 wires going to it. most likely a heavy purple wire would be the power to the pump. It has to have 12 volts to it to work. The sender may have 3 wires, 5 volts, ground, and sense. the pump connector would have 12 volts, ground and 5 volts for the fuel gauge sender down in the tank.
If the 12 volts is not there, check the fuel pump relay. it is usually up on the drivers side firewall.
With the key in the on position without starting the engine, you should have 12 volts to the pump for 3 seconds then it will click off. Without cranking the engine you should be able to locate the relay by the clicking sound.
There is also the obvious, like checking the fuel pump fuse.

Jan 11, 2011 | 2003 Chevrolet Avalanche

2 Answers

1993 rodeo not running no power to fuel pump


if there is no power to the fuel pump check relays and fuses....UNDERHOOD FUSE & RELAY PANEL IDENTIFICATION Fig. 2: Underhood Fuse & Relay Panel Identification Courtesy of ISUZU MOTOR CO. Fusible Link Identification ? A - 80 Amp (1991-92 3.1L) ? A - 60 Amp Main-1 ? B - 30 Amp Main-2 ? C - 30 Amp (1993-94) ECM (3.2L) ? D - 30 Amp Condenser Fan (A/T Models) Relay Identification ? 1 - Headlight Relay ? 2 - A/C - Heater Relay ? 3 - Starter Relay ? 4 - A/C Compressor Relay ? 5 - Charge Relay ? 6 - Fuel Pump Relay ? 7 - ECM Relay ? 8 - Wiper Relay Fuse & Circuit Breaker Identification ? 1 - 15 Amp (1991) ECM, Fuel Injection System ? 1 - 15 Amp (1992-94 2.6L) ECM, Fuel Injection System ? 1 - 10 Amp (1992-94 3.1 & 3.2L) Heated Oxygen Sensor, Fuel Injection System ? 2 - 20 Amp (1991-92) Fuel Pump ? 2 - 20 Amp (1993-94 2.6L) Fuel Pump ? 2 - 15 Amp (1993-94 3.2L) Fuel Pump ? 3 - 10 Amp (1991) ? 3 - 15 Amp (1992-94) Turn Signal Lights, Hazard Warning Flasher Lights ? 4 - 10 Amp Horn, Door Locks ? 5 - Not Used (1991 3.1L) ? 5 - 10 Amp Charging System, Charge Warning Light WARNING: Always disconnect battery ground cable before servicing "high- current fuses. It is recommended that "high-current" fuses be replaced by a qualified technician. Page 1 of 2 FUSES & CIRCUIT BREAKERS -1994 Isuzu Rodeo LS? 6 - Not Used (1991) (1992-93 2.6L) ? 6 - 10 Amp (1992-94 3.1L & 3.2L) A/T Interlock System ? 6 - 10 Amp (1994 2.6L) Heated Oxygen Sensor, Fuel Injection System ? 7 - 20 Amp Heater/Air Conditioning Blower Controls ? 8 - 10 Amp Air Conditioner Compressor Controls ? 9 - 10 Amp Right Headlight ? 10 - 10 Amp Left Headlight © 2008 Mitchell Repair Information Co., LLC.
62217_isuzfuse_1.jpg
Underhood fuse block swap out relay #7 thats the ECM relay.
Ground Circuits Using a DVOM, touch negative voltmeter lead to a good ground. Touch positive voltmeter lead to each ground terminal. With vehicle running, voltmeter should indicate less than one volt. If reading is greater than one volt, check for open, corrosion and loose connection on ground lead. See ECM GROUND LOCATION table for ECM ground location.
Page 1 of 1 SYSTEM/COMPONENT TESTS - 2.6L EFI -1994 Isuzu Rodeo

Mar 28, 2010 | 1993 Isuzu Rodeo

2 Answers

2003 Volkswagen Golf Problem


it should be number 42


MKIV FUSE LIST
1. Washer nozzle heaters, glove compartment light, memory seat control module (10A).
2. Turn signal lights (10A).
3. Fog light relay, instrument panel light dimmer switch (5A).
4. License plate light (5A).
5. Comfort system, cruise control, Climatronic, A/C, heated seat control modules, automatic day/night interior mirror, control module for multi-function steering wheel, control unit in steering wheel (7.5A).
6. Central locking system (5A).
7. Back-up lights, speedometer vehicle speed sensor (VSS) (10A).
8. Open
9. Anti-lock brake system (ABS) (5A).
10. Engine control module (ECM): gasoline engine (10A); diesel engine, Model Year 2000 > (5A).
11. Instrument cluster, shift lock solenoid (5A).
12. Data Link Connector (DLC) power supply (7.5A).
13. Brake tail lights (10A).
14. Interior lights, central locking system (10A).
15. Instrument cluster, transmission control module (TCM) (5A).
16. A/C clutch, after-run coolant pump (10A).
17. Open.
18. Headlight high beam, right (10A).
19. Headlight high beam, left (10A).
20. Headlight low beam, right (15A).
21. Headlight low beam, left (15A).
22. Parking lights right, side marker right (5A).
23. Parking lights left, side marker left (5A).
24. Windshield and rear window washer pump, windshield wiper motor (20A).
25. Fresh air blower, Climatronic, A/C (25A).
26. Rear window defogger (25A).
27. Motor for rear windshield wiper (15A).
28. Fuel pump (FP) (15A).
29. Engine control module (ECM) gasoline engine (15A); diesel engine (10A).
30. Power sunroof control module (20A).
31. Transmission control module (TCM) (20A).
32. Injectors: gasoline engine (10A); diesel engine (15A).
33. Headlight washer system (20A).
34. Engine control elements (10A).
35. 12 V power outlet (in luggage compartment) (30A).
36. Fog lights (15A).
37. Terminal (86S) on radio, Instrument cluster (10A).
38. Central locking system (with power windows), luggage compartment light, remote/fuel tank door, motor to unlock rear lid (15A).
39. Emergency flashers (15A).
40. Dual tone horn (20A).
41. Cigarette lighter (15A).
42. Radio (25A).
43. Engine control elements (10A).
44. Heated seats (15A).
Fuse arangements in fuse bracket/battery:
S162. Glow plugs (coolant) (50A).
S163. Fuel pump (FP) relay/glow plug relay (50A).
S164. Coolant fan control (FC) control module/coolant fan (40A).
S176. Relays panel interior (110A).
S177. Generator (GEN) (90 Amp.) (110A).
Generator (GEN) (120 Amp.) (150A).
S178. ABS (hydraulic pump) (30A).
S179. ABS (30A).
S180. Coolant fan (30A).

Jul 09, 2008 | 2003 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

78257 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...