Question about Ford F-150

1 Answer

Having trouble removing power steering pump from 88 f1

Posted by on

  • Lisa Boley Dodson
    Lisa Boley Dodson Apr 23, 2010

    yes this is very helpful, i like pictures
    thank you

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 17,970 Answers

Ford Pick-ups and Broncos 1987-1996 Repair Guide
Ford C-II Power Steering Pump
This pump is used by all models except the F-Super Duty stripped chassis and motor home models.

REMOVAL & INSTALLATION
(see Figures 1, 2, 3, 4, 5 and 6)

having trouble removing power steering - c9ca416.jpg

Fig. 1: Power steering pump installation on the 1987 4.9L EFI

7dae978.jpg

Fig. 2: Power steering pump installation on the 1988-96 EFI

1837679.jpg

Fig. 3: Power steering pump installation on the 1988-96 8-5.0l EFI and 5.8L EFI

f0cd50e.jpg

Fig. 4: Power steering pump installation on the 7.5L EFI

ca629fd.jpg

Fig. 5: Power steering pump installation on the 7.5L 4-bbl
9435044.jpg

Fig. 6: Power steering pump installation-diesel engines

  1. Disconnect the return line at the pump and drain the fluid into a container.
  2. Disconnect the pressure line from the pump.
  3. Loosen the pump bracket nuts and remove the drive belt. On the 4.9L engine or 5.0L engine with a serpentine drive belt, remove belt tension by lifting the tensioner out of position.
  4. Remove the nuts and lift out the pump/bracket assembly.
  5. If a new pump or bracket is being installed, you'll have to remove the pulley from the present pump. This is best done with a press and adapters.
  6. Installation is the reverse of removal. Note the following torques:
    Pivot bolt (4.9L and 5.0L): 45 ft. lbs. (61 Nm) Pump-to-adjustment bracket: 45 ft. lbs. (61 Nm) Support bracket-to-engine (5.8L): 65 ft. lbs. (88 Nm) Support bracket-to-water pump housing (4.9L): 17 ft. lbs. (23 Nm) Support bracket-to-water pump housing (5.0L, 5.8L): 45 ft. lbs. (61 Nm) Pressure line-to-fitting: 29 ft. lbs. (39 Nm) Adjustment bracket-to-support bracket: 4.9L, 5.0L, 5.8L: 45 ft. lbs. (61 Nm); 7.5L and Diesel: Long bolt-65 ft. lbs. (88 Nm) Short bolt-45 ft. lbs. (61 Nm)

Hope this help to solve it.

Posted on Apr 23, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Well, do i remove the power steering pump or pull the pully to remove the water pump and if the pump, is access from underneath ??


you have to remove your power steering pump to replace your water pump you remove one bolt from the top and one from underneth by going threw holes in power steering pump pully

Sep 17, 2011 | 1995 Oldsmobile 88

1 Answer

How to install a power steering high pressure line on a 1998 olds 88 regency


Hi,
You will need line wrenches to get the line off the steering gear assembly (tight in there near the frame sub assembly) First you will want to remove the drive belt from the power steering pump. Then remove the bolts from pump to bracket and lift pump up. On back of pump, remove low pressure line and drain fluid into a container. Under pump, remove high pressure line, and push it downward toward floor. From under car, follow the line to the steering gear, ( the line may have a keeper clamp or two for stationary support to remove along the way) then detach. Installation is reverse of disassembly........Not fun, but doable.....Mike

Jun 22, 2011 | 1998 Oldsmobile 88

1 Answer

Power steering belt needs to be replaced and tightened, how do i do it?


The belt is changed by loosening the power steering pump at the adjustment bolt and also the pivot bolt: The following instructions tell you how to remove the whole power steering pump, but you just have to adjust the tension with it.

A long pry bar might help to tighten the tension until there is like 1/2" to 3/4" deflection in the middle of the belt between two pulleys, and when running there doesn't appear to be a lot of play in the appearance of the belt while the pulleys are rotating, and that when the steering wheel is turned, you don't hear any squealing indicating a slipping of the drive belt.

Good luck on this repair:


Power Steering Pump REMOVAL & INSTALLATION
  1. Remove the hoses at the pump and tape the openings shut to prevent leakage.
  2. Remove the pump drive belt.
  3. Remove the retaining bolts, any braces and the pump.
  4. If a new pump is being installed, and the pulley is being transferred, a puller is necessary to remove the pulley. To install:
  5. Torque hose fittings to 20 ft. lbs. (27 Nm). Fill the reservoir with approved power steering fluid and turn the pump backward (counterclockwise as viewed from in front) until bubbles no longer appear in the reservoir.
  6. Any time the pump is removed, air must be bled from the system upon reinstallation. Bleed the system as described in the next procedure. Fig. 1: Exploded view of the power steering pump assembly 85848076.gif
    Fig. 2: A common power steering pump location 85848077.jpg prev.gif next.gif

Nov 06, 2010 | 1985 Oldsmobile Delta 88

1 Answer

How do replace the power steering pump on 1996 oldsmobile delta 88


remove the pressure and return line, the belt, remove the mounting bolts. Use a "power steering pulley puller" to remove the puller. This tool also works as an installer.

Apr 16, 2010 | 1996 Oldsmobile 88

1 Answer

Where to I put the power steering fluid? I can't


Hi, without looking at the engine in front of me, I can tell you to look for the belt that operates everything, and you will find the power steering pump. It will have a small pulley on it with the fan belt around that. It will also have a cap on the top of it. You remove the cap to pour the fluid in. On the body of the pump it will have 2 lines 1 for full cold and 1 for full hot. This means if the engine is hot from driving or cold from setting. Should be very easy to find if you follow what I have said. Good Luck,
Shastalaker7

Jan 21, 2010 | 1999 Oldsmobile 88

1 Answer

88 corsica


Hi, no need to raise the engine. you can use these steps to replace your pump.

To replace the power steering pump, proceed as follows:

1. Disconnect the power steering return hose from the remote reservoir or pump. Allow the fluid to drain from this hose into a drain pan. Discard the used fluid.
2. Loosen the bracket or belt tension adjusting bolt, and the pump mounting bolt.
3. Loosen the belt tension until the belt can be removed. On some cars, it is necessary to lift the vehicle on a hoist and gain access to the power steering pump from underneath the vehicle.
4. Remove the hoses from the pump, and cap the pump fittings and hoses.
5. Remove the belt tension adjusting bolt and the mounting bolt, and remove the pump.
6. Check the pump mounting bolts and bolt holes for wear. Worn bolts must be replaced. If the bolt mounting holes in the pump are worn, pump replacement is necessary.
7. Reverse steps 1 through 5 to install the power steering pump. Tighten the belt as described previously, and tighten the pump mounting and bracket bolts to the manufacturer's specifications. If o-rings are used on the pressure hose, replace the o-rings. Be sure the hoses are not contacting the exhaust manifold, catalytic converter, or exhaust pipe during or after pump replacement.
8. Fill the pump reservoir with the manufacturer's recommended power steering fluid, and bleed air from the power steering system as described earlier.

May 21, 2009 | 1988 Chevrolet Corsica

1 Answer

I need a description on how to change Power Steering Pump


if your looking to do it yourself try and get a haynes manual from your local autopart store

May 21, 2009 | 1998 Oldsmobile 88

2 Answers

How do I remove oil pump pulley to replace the water pump?


If you mean the power steering pump, it will have to be removed to access the bolt. It's just 2 bolts. You get them through the holes in the power steering pump. Just unbolt it and push it aside.

Feb 14, 2009 | 1995 Oldsmobile 88

2 Answers

I need to move the power steering pump to replace the water pump


the pulley needs to be removed to remove the PS pump, this pulley is pressed onto a tapered shaft (they used a bolt around 35 years ago), it requires a special power steering pulley remover/installer tool, u can borrow this tool from Kragen and other parts stores like them, as how it works, it can be a little hard to set it up if u have never used this tool before.

Jan 23, 2009 | 1996 Oldsmobile 88

1 Answer

Removal of power steering pump on 1998 GMC Sierra 1500


you need a power steering pump puller the rest is simple any trouble let me know

Dec 14, 2008 | 1998 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

518 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...