Question about Chevrolet S 10

1 Answer

My transmission not changing gears like it's suppose too...

Posted by on

  • yadayada
    yadayada May 11, 2010

    manual or auto?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Ye ye ye

Posted on Apr 23, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

E39 528 changes from 1st to 2nd i have changed the gearbox and it still has the same problem


gear boxes are supposed to change from 1st to second.
that is the nature of transmissions in that they change gear ratios as required by you or the transmission control module
so you will have to post again stating the reason you had to consider the transmission changes or the symptoms displayed in the fault codes that required the changes

Nov 30, 2016 | Cars & Trucks

1 Answer

Transmission problem, 1990 f150 5.0 automatic 4x4


Either the engine idle speed is too slow or the transmission fluid pump is not delivering adequate pressure to the valve body. There may be foreign material blocking one or more passages in the valve body - a flush and fill is supposed to take care of that, but it doesn't always get it if there is too much metal dust in there.

Jan 27, 2015 | Cars & Trucks

1 Answer

Gear shift moves but indicator doesn't change and transmission doesn't engage.


try disconnecting cable to transmission turn the shifter on transmission manually down there connect cable again start car try it if not try it again turn once then connect cable again then try it if not the transmission is not good

Jan 31, 2013 | 2002 Nissan Maxima

2 Answers

Code p0734 I just replaced eng. and trans. now have this code.


Engine Light ON (or Service Engine Soon Warning Light)
- Incorrect transmission shifting Possible causes - Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit Tech notes Start by inspecting the transmission fluid level and condition, and change fluid if necessary. When is the code detected? P0734 is detected when A/T cannot be shifted to the 4th gear position even if electrical circuit is good. P0734 NISSAN Description This diagnosis monitors actual gear position by checking the torque converter slip ratio calculated by Transmission Control Module (TCM) as follows:

Torque converter slip ratio = A x C/B

A: Output shaft revolution signal from revolution sensor
B: Engine speed signal from Engine Control Module (ECM)
C: Gear ratio determined as gear position which TCM supposes

If the actual gear position is higher than the position (4th) supposed by TCM, the slip ratio will be more than normal. In case the ratio exceeds the specified value, TCM judges this diagnosis malfunction.

Aug 09, 2011 | 1995 Nissan Altima

1 Answer

My came with a code po734 is that a big problem?


DTC P0734 - Improper Ratio for Fourth Gear.
P0734 is detected when A/T cannot be shifted to the 4th gear position even if electrical circuit is good.

This diagnosis monitors actual gear position by checking the torque converter slip ratio calculated by Transmission Control Module (TCM) as follows:

Torque converter slip ratio = A x C/B

A: Output shaft revolution signal from revolution sensor
B: Engine speed signal from Engine Control Module (ECM)
C: Gear ratio determined as gear position which TCM supposes

If the actual gear position is higher than the position (4th) supposed by TCM, the slip ratio will be more than normal. In case the ratio exceeds the specified value, TCM judges this diagnosis malfunction.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Incorrect transmission shifting

Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit

Tech notes: Start by inspecting the transmission fluid level and condition, and change fluid if necessary.


Test and check it and send us ypur comments.

May 14, 2011 | 2000 Land Rover Discovery

2 Answers

Ford trauras trouble code 732 - was told transmission code 732 was being produced, what does a code 732 say?


P0732 FORD - Incorrect Second Gear Ratio
Transmission in second gear and the ECM detected an incorrect gear ration. This diagnosis monitors actual gear position by checking the torque converter slip ratio calculated by Transmission Control Module (TCM) as follows:

Torque converter slip ratio = A x C/B

A: Output shaft revolution signal from revolution sensor
B: Engine speed signal from Engine Control Module (ECM)
C: Gear ratio determined as gear position which TCM supposes

If the actual gear position is higher than the position (2nd) supposed by TCM, the slip ratio will be more than normal. In case the ratio exceeds the specified value, TCM judges this diagnosis malfunction.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Incorrect transmission shifting

Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit

Tech notes
Start by inspecting the transmission fluid level and condition, and change fluid if necessary.


Hope helps.

Apr 26, 2011 | Ford Taurus X Cars & Trucks

2 Answers

Transmission will not shift into 3rd gear


Is your ABS light on? If there is a problem with your ABS the transmission will not shift above 2nd gear. I had a similar problem, it had to do with a faulty connection on the transfer case.

Aug 08, 2009 | 1999 Chevrolet Blazer

1 Answer

Transmission doesn`t make gear shifts


No matter what the issue the trans will have to be torn down to some degree to check the shift solenoids and the valve body, also a self test for trouble codes will be needed to see if anything shows up in the powertrain control module memory.

Nov 03, 2008 | 1995 Oldsmobile Aurora

1 Answer

Transmission won't shift out of 1st gear


the output spped sensor is on the drivers side rear of the transmission case..its a 2 wire connector..the wires are dark bluewith a black tracer and light green with a white tracer

Sep 30, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...