Question about 2004 Dodge Ram 1500

Open Question

Timing marks for 4.7 litre dodge ram NEED SPECS!!

Timing marks for 4.7 litre dodge ram 2002? Please help.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 118 Answers

SOURCE: NEED TORQUE SPECS AND SEQUENCE FOR 02 DODGE 2.4 V6 STRATUS

  1. Tighten bolts in sequence shown in (Fig. 23), using the following steps and torque values:
    • Step 1: Bolts 1 - 8 to 48 Nm (35 ft. lbs.)
    • Step 2: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 3: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 4: Bolts 1 - 8 to +90° . Turn Do not use a torque wrench for this step.
    • Step 5: Bolts 9 - 11 to 28 Nm (250 in. lbs.)
  • I tried to send a pic of the head bolt numbers but it wont let me so e mail me dbern002@att.net have a good day DB

Posted on Feb 01, 2009

Ad
  • 1596 Answers

SOURCE: Need timing marks for 2002 ford explorer 4.0




The Info I Have Is Extensive and Has Illistrations, I Need to Emali it to You As it is Very Large, This Is A Small Example Im @rejakwilson@aol.com

Special Tool(s)

  1. With the vehicle in neutral, position it on a hoist.
  2. Remove the intake manifold.
  3. Remove the fuel supply manifold.
  4. Remove the accessory drive belt.
  5. Remove the thermostat housing.
  6. Remove the roller followers.
  7. NOTE: You must retime the LH and RH camshafts when either camshaft is disturbed. Turn the crankshaft clockwise to position the number one cylinder at top dead center (TDC).
  8. NOTE: Late build pulley shown, early build pulley similar. NOTE: The special tool must be installed on the damper and should contact the engine block to position the engine at TDC.

Posted on Jul 24, 2009

motor1258
  • 6674 Answers

SOURCE: timing marks for my 87 dodge ram 50 2.0

8 degrees BTDC.

Posted on Jul 26, 2009

johnjohn2
  • 5763 Answers

SOURCE: I am changing the timing belt on my 1989 Ram-50

here are two diagrams to help you do your timing belt, one to line up the timing belt and the other to line up the balance shaft belt, good luck, hope this is what you needed and hope it helps.da22fd0.gifdc33216.gif

Posted on Feb 18, 2010

johnjohn2
  • 5763 Answers

SOURCE: need too know the timming marks on where to set

Here are the timing marks for the timing belt and also the balance shaft, when replacing the timing belt you should also replace the balanceshaft belt heres a diagram for both of them good luck and hope this helps.35de2d2.gif9665995.gif

Posted on Aug 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT IS THE HARMONIC BALANCER TORQUE SPECS FOR A 2002 2.7L DODGE INTREPID?


This is for a 5.7 Ram
the torque should be 150-180 ft lbs. anywhere in this range is good.
http://www.fixya.com/cars/t8915727-need_know_torque

Register at this website to get all the torque specs.

http://www.autozone.com/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f8037c5e2

Aha, I took me 30 minutes, but here you go. The secret was the change of search query wording to;
2002 2.7 DODGE INTREPID TORQUE SPECS crankshaft damper

(198) Install damper center bolt. Tighten center bolt
while holding the damper with Special Tool 8191 to
170 N•m (125 ft. lbs.) (Fig. 76).

http://www.dodgeintrepid.net/18-general-discussion-second-generation/61664-so-your-2-7-ready-some-100k-repairs.html


WHAT IS THE HARMONIC BALANCER TORQUE SPECS FOR 2002 2 7L DODGE INTREPID...

Jan 11, 2017 | 2002 Dodge Intrepid

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

My 2002 dodge 1500 has 392 rear end gears iwhant 353 gears what do ido


you can remove the axles and the drive shaft then open the differential to remove the carrier gear assembly(ring gear,side gears)then remove the pinion gear.replace these with the new gear set and get the clearance specs for the pinion depth and carrier gear clearance and adjust until within specs.you can either pickup new gear sets or one from the wreckers with the shims to start with.you will need a backlash dial gage to know if the backlash clearance is within specs as well as marking ink to know if the gear mating surface is riding in the proper area of contact.

Jul 11, 2011 | 2006 Dodge Ram 2500

1 Answer

Need too know the timming marks on where to set them at on a 1988 dodge ram 50 2.0 4 cyl


Here are the timing marks for the timing belt and also the balance shaft, when replacing the timing belt you should also replace the balanceshaft belt heres a diagram for both of them good luck and hope this helps.35de2d2.gif9665995.gif

Aug 13, 2010 | 1988 Dodge Ram 50

1 Answer

I am changing the timing belt on my 1989 Ram-50 and need to know how to line it up. the motor is a 2.0 litre and uses 2 belts. What are the marks and where are they?


here are two diagrams to help you do your timing belt, one to line up the timing belt and the other to line up the balance shaft belt, good luck, hope this is what you needed and hope it helps.da22fd0.gifdc33216.gif

Feb 18, 2010 | 1989 Dodge Ram 50

1 Answer

Timing specs 1993 cheverolet vortec 4.2 litre v-6


make sure the number one piston is on top dead center on the compression stroke, and the timing marks are aligned on the balancer, drop in the distributor with the rotor facing th # 1 terminal on the cap.

Apr 26, 2009 | Chevrolet Blazer Cars & Trucks

1 Answer

V8 5.9 liter Engine Timing


it's between 4 and 2 degrees before top dead center.
PLEASE RATE MY ANSWER.

Feb 26, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Put new oilpump and hadto remove timeing belt and gears. i need t


For the 1986 Dodge Ram 50 2.0L AND 2.6L 4-Cylinders:

Firing Order:
1-3-4-2

Cylinders:
(back)
...4
...3
...2
...1
(front)

Distributor:
.(back)
3.......4
1.......2
.(front)

For the Timing Marks: Click on the following Link. It has the Position of the Cranshaft and Camshaft and their respective marks.

http://www.2carpros.com/car_repair_information/year/1986/make/dodge/model/ram_50/1986_dodge_ram_50_timing_belt_diagram_marks.htm

Jan 02, 2009 | 1986 Dodge Ram 50

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

672 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...