Question about 2000 Jeep Grand Cherokee

1 Answer

Where is the governer sensor located - 2000 Jeep Grand Cherokee

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,511 Answers

Hello and Welcome to fixYa!
It is located in the valve body of the transmission. It governs the pressure for the up and down shifts of the transmission.

Here is the Image that can help you out:
where is the governer sensor located - 0ba0eee.gif

Hope this would help you out.

Best Of luck,

Please do RATE my solution, If found HELPFUL.

Regards.

Posted on Apr 23, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 trcktion control .where the senor is located at


The traction control system on most modern autos uses the input from the wheel speed sensors of the Anti-lock Braking System. There isn't one sensor that governs that system. There is usually one sensor at each wheel. Some older systems use one for both rear wheels that have a solid rear axle. I hope this helps. If you have any other questions, we're all here listening.

Jan 29, 2017 | Cars & Trucks

1 Answer

Cruse control stopped working and the fuse is good light comes on but will not work.


cruise control s are governed by by 4 sensors and switches
1--- brake sensor ---brake application
2 --clutch sensor ( if manual)--clutch application ( foot resting on clutch pedal will turn it off)
3--- VSS if auto for road speed input
4---ignition control module -- for rpms input
have a service technician check ti out

Feb 28, 2016 | Cars & Trucks

2 Answers

My 1994 GMC Suburban wont shift out of first.....but will shift to second manually but wont go any higher........?


Sounds like a vehicle speed sensor, it governs shifting based on engine RPM vs Transmission RPM among other things. Located usually on the rear tailshaft or rear transfer case on the majority of 4L60E automatics.

Mar 25, 2015 | 1994 GMC Suburban

1 Answer

Hi. My merc 1999 C 200 lefthand rear CV joint next to the diff got loose and broked the cover of the diff. I replaced the diff cover as well as both left and right hand sideshafts with cv joints. From...


Hi Pieter, The rear shafts both have ABS sensors which are gear like rotors and send signals to the computer. The signals received govern the ABS the traction control and speed sensors which in turn supply info to the transmission control and govern gear change. Have the rotors examined for damage and the pick up sensors which can be located on each of the four wheels. I suspect that one of the rear rotors is out of alignment or there is damage to one of the wheel sensors. Regards John

Feb 19, 2012 | 1997 Mercedes-Benz C-Class

1 Answer

The engine of my Echo 2001 suddenly misfired while I was travelling on a carriagway at about 50mph. I started the engine sucessfully for once and she ran for another minutes and stopped again. The engine...


This sounds like a crank sensor problem (possibly a cam sensor). This sensor governs engine timing. These sensors suffer from temperature induced faults, as the engine warms up the body of the sensor expands and causes a break in the internal sensor circuit. Often the sensor will work fine whilst the engine is cold but after 15 minutes when the engine is hot then the misfire begins. Check that the sensor connection is on tight and free of dirt/corrosion. The sensor is either located on a) the engine next to the bell housing of the transmission or b) on the 'front' (drive belt end) of the engine next to the crank harmonic balance pulley. It is fairly small black plastic device held in place with a bolt and with an electrical connection to the top of it.

Jul 30, 2011 | 2005 Toyota ECHO

1 Answer

What this mean p1756


P1756 what does this mean: It is transmission related, difinition is: transmission governor pressure not equal to target...its a transmission code this is a common failure... have seen these governer pressure sensors fail often.... most codes are governer pressure sensor volts too high or low, governer pressure sensor not equal to target.. Most of the time you replace the governer pressure sensor and soleniod.. I would recommend you to fix this problem if not you will end up burning the clutches in the trans... The trans pan needs to be removed....the sensor is bolted to the valve body and is located on the pass front side of the valve body.

Jun 01, 2010 | 2000 Dodge Durango

2 Answers

MY CLIO 1.6L IS STRUGGLING TO START WHEN I FIRST START IT EVERYDAY BUT ONCE IT HAS STARTED IT IS FINE ALL DAY UNTIL I TRY AND START IT THE NEXT DAY.


If the car is fuel injected then the coolent temperature sensor is faulty and needs replacing, if its carburator then it's got a sticking auto choke.
The coolent temp sensor tells the ecu how much more fuel to put in governed on the engine coolant temperature, if the sensor is faulty it does not know that it should be putting more fuel in.

May 08, 2009 | Renault 18I Cars & Trucks

1 Answer

200 Pontiac Grand Am over 3500 RPM loss of power


on almost all gm cars after 96 the engines were governed to not free rev over 4000rpm. when in gear and power braking the rpms stay lower cause of the load on engine. when reving above 3500 rpms the computer cuts back the timing and fuel to reduce engine damage if left to free rev. hop that helps.

Apr 26, 2009 | Pontiac Grand Am Cars & Trucks

2 Answers

Car cut off


I had this happen to my car several years ago. Turned out to be the power train computer module (I think that's what it was called) - some computer sensor that was related to emissions but not the O2 sensor. The federal government requires it so my dealer replaced it at no charge. Mine used to shut off after I hit speeds in excess of 45 mph and then I'd have to restart the car and drive slowly. After checking the battery and alternator, this fix was the last option - never had a problem since!

Dec 01, 2008 | 1997 Dodge Stratus

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...