- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
? 1:27 https://www.youtube.com/watch?v=6rLi0I7vRIw
Mar 30, 2011 - Uploaded by Garden City Jeep Chrysler Dodge Ram SRT
The staff at Garden City Jeep Chrysler Dodge are ready to help you. ... Garden City Jeep Chrysler Dodge has The Can-Do Crew show you how to lower your spare tire. ... Pacifica, Durango, Charger and Liberty for the Hempstead, Queens, Brooklyn ...Installation of a Trailer Hitch on a 2006 Chrysler Pacifica ...Missing: nut sided adapter stored
Free video on how to fix a flat tire in a 2005 Chrysler Pacifica Touring 3.5L V6. Complete instructions for using the jack kit and spare tire in a 2005 Chrysler Pacifica... Most Chrysler jack kits include the jack, a jack handle and a lug nut wrench.
Section 00-02: Lifting, Jacking and Spare Tire Stowage
1995 Aerostar, Ranger, Explorer Workshop Manual
Tire, Spare, Removal, Aerostar
If the Aerostar is a standard length vehicle the spare tire is mounted inside to a carrier at the left rear quarter panel. To remove the spare tire, remove the wing nut and plate. A flat tire can be temporarily stowed in the same location.
If the Aerostar is the bus with a standard length body or extended length (all models), the temporary spare tire is stowed at the rear of the vehicle under the body.
The Aerostar standard length E-4WD bus spare tire is mounted on the floor.
Insert lug nut wrench into the actuator hole and turn counterclockwise until the cable extends to allow the spare tire to be pulled rearward from under the vehicle.
Slide spare tire to the rear and remove the retainer from the wheel.
To stow cable/retainer with spare tire removed, insert cable fitting into carrier rear wall slot, place wheel retainer against the carrier, and turn lug nut wrench clockwise until slack is removed.
open the rear door..the jack gonna be right or left wall..open out door compartment on the wall and you will see the jack and the tire wrench...connect the wrench together and it gonna be like 4 feet long...look under the truck on the rear and there you will see the tire...put the long wrench in the hole next to lic plate and start turn counterclockwise and the tire will come down..good.luck
If the spare tire does not lower to the ground,the secondary latch is engaged causing the tire not to lower Your vehicle has an underbody-mounted tire hoist assembly equipped with a secondary latch system.It is designed to stop the spare tire from suddenly falling off your vehicle if the cable holding the spare tire is damaged.For the secondary latch to work,the tire must be stored with the valve stem pointing up. 1.Check under the vehicle to see if the cable is visible.If it is not visible proceed to Step 6. 2.If visible,first try to tighten the cable by turning the wheel wrench clockwise until you hear two clicks or feel it skip twice.You cannot overtighten the cable. 3.Loosen the cable by turning the wheel wrench counterclockwise three or four turns. 4.Repeat this procedure at least two times.If the spare tire lowers to the ground continue with Step 2 of removing the Spare. 5.Turn the wrench counterclockwise until approximately 6 inches (15 cm) of cable is exposed. 6.Attach the jack handle,extension and the wheel wrench to the jack and place it under the vehicle towards the front of the rear bumper.Position the center lift point of the jack under the center of the spare tire. 7.Turn the wrench clockwise to raise the jack until it lifts the end fitting. 8.Continue raising the jack until the spare tire stops moving upward and is held firmly in place. 9.Lower the jack by turning the wheel wrench counterclockwise.Keep lowering the jack until the spare tire slides off the jack or is hanging by the cable. 10.Disconnect the jack handle from the jack and carefully remove the jack.Use one hand to push against the spare while firmly pulling the jack out from under the spare tire with the other hand.
Put the car on a level ground, with the transmission in PARK. Lossen the nuts of the tire to change. Chuck back-tires if changing front, or chuck front-tires if changing back-tires. Jack up the car enough to raise the concerned tire off the ground. Remove nuts, and pull out the tire. Put in spare tire.
Hand tighten the nuts a considerable, but you might use the wrench to tighten a bit because this is a big/heavy car. Lower the car, and again tighten the nuts securely in a diagonal pattern with the wrench- two grunts used to be the rule of the thumb.
Location of the spare tire and tools
The spare tire and tools for your vehicle are stowed in the following
Spare tire Under the vehicle, just forward of
the rear bumper
Jack assembly Under the third row bench seat in
the tool bag
Removing the jack and tools
1. Lift the 3rd row seat cushion.
2. Remove the jack assembly from the bag under the seat.
Removing the spare tire
1. Open the liftgate, locate the U-shaped slits in the carpet, and flip up
the piece of carpet to expose the hex nut.
2. Insert the lug nut wrench on the
hex nut in cargo floor.
3. Turn the wrench
counterclockwise until tire is
lowered to the ground and the cable
is slightly slack.
4. Remove the retainer from the
spare tire. It may be necessary to
lift one end of the tire to disengage