Question about 2007 Mercedes-Benz ML320 CDI

Open Question

How to replace a side mirror on a ml270 53 plate electric i just need to put a glass back on. Some one has taken the mirror out. i have a mirror but cant seem to find a way of sloting it in. Please could you help it does get dangerous not seeing in the dark

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 540 Answers

SOURCE: how to replace mirror plate, the plastic behind

push the mirror all the way in, firmly support the face of the mirror with a rag and your hand, reach in behind the mirror, stick the screwdriver between the glass and motor assembly. with a twisting motion, you should be able to free the mirror, and then disconnect the wires. after obtaining a new mirror from your local dealer, position the mirror motor assembly so its straight across, cover the new mirror face with a cloth plug the wires in and firmly press glass into place it should snap in

Posted on Jan 08, 2010

Danniboi
  • 1098 Answers

SOURCE: the glass popped out of my side mirror when I hit

yes just be carefull there should be very small holes on the back of the mirror they are not always that obvious but they click back in or should do. to the round fixing plate push from the middle and wiggle.

Posted on Jan 13, 2010

  • 1 Answer

SOURCE: Need to get a "backing

I need the same thing for a 2004 Explorer Sportrac. I can't find the "backing plate" either. Only the glass. No junkyard will sell me only the plate and glass. I did find a complete mirror assembly (housing, gasket, glass) for $37.89. This includes shipping. I got it from partsgeek.com. It just arrived today and looks to be perfect. I have not installed it yet. Hope this helps you out.

Posted on Dec 06, 2010

emissionwiz
  • 75797 Answers

SOURCE: i have taken out spark plug leads on 1995 daewoo 1.5i to replace and can't get right order to put back ? please help

Firing order is 1-3-4-2

Posted on Sep 18, 2012

  • 1 Answer

SOURCE: mt drivers side wing mirror glass has popped out,

Hi,whilst reversing the drivers wing mirror popped out (the whole thing) and is hanging by a cable. My car is a Mercedes Benz 200. Can I fix it??

Posted on May 22, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Ford Falcon - How to fix/replace the mirror glass and backing plate of the driver side mirror unit?


Use a heat gun or hair dryer to heat up the glass. This will soften the glue which holds the mirror onto actuator. Gently pry the mirror off. the actuator can then be unscrewed and removed.

May 25, 2014 | 1999 Ford Falcon

1 Answer

Need to get a "backing


I need the same thing for a 2004 Explorer Sportrac. I can't find the "backing plate" either. Only the glass. No junkyard will sell me only the plate and glass. I did find a complete mirror assembly (housing, gasket, glass) for $37.89. This includes shipping. I got it from partsgeek.com. It just arrived today and looks to be perfect. I have not installed it yet. Hope this helps you out.

Nov 06, 2010 | Toyota Corolla Cars & Trucks

1 Answer

Replace side view mirror 2002 chevy tahoe


Once you've purchased a replacement mirror glass based on your specific make, model and year simply follow the steps below:

  • Remove all existing glass from the mirror head's plastic inner platform (backing plate).
  • Clean backing plate with rubbing alcohol. Clean back of replacement mirror with Burco Window Glo or other glass cleaner.
  • Apply the Burco Redi Stick adhesive patches and or silicone/urethane to the replacement mirror's back or to the backing plate itself.
  • Align and press replacement mirror to the backing plate.
  • Clean the installed Burco Redi Cuts mirror with Burco Window Glo or other urethane-safe glass cleaner.

Oct 09, 2009 | 2002 Chevrolet Tahoe

1 Answer

How do you replace the driver side rear view mirror on a 2007 Toyota Sienna?


Once you've purchased a replacement mirror glass based on your specific make, model and year simply follow the steps below:

  • Remove all existing glass from the mirror head's plastic inner platform (backing plate).
  • Clean backing plate with rubbing alcohol. Clean back of replacement mirror with Burco Window Glo® or other glass cleaner.
  • Apply the Burco Redi Stick® adhesive patches and or silicone/urethane to the replacement mirror's back or to the backing plate itself.
  • Align and press replacement mirror to the backing plate.
  • Clean the installed Burco Redi Cuts® mirror with Burco Window Glo® or other urethane-safe glass cleaner.

Aug 04, 2009 | Toyota Sienna Cars & Trucks

2 Answers

Replacing a rear view mirror


You have to CAREFULLY ( probably wise to wear safety goggles ) and with a flat blade screwdriver, pry out ALL the broken mirror glass wearing gloves. Now with the 2 adhesive strips, align mirror glass and adhere to base. Hope this helps

May 13, 2009 | 2008 Subaru Forester

1 Answer

What replacement mirror would I need ??


Hello Joe

Yes you have an E46, You need to order the UK drivers side glass and make sure you specify it's a coupe. the saloons have a different wing mirror.

Hope this helps, please don't forget to rate me.

Mar 16, 2009 | 1999 BMW 328 Series

1 Answer

I need to replace the mirror glass on a 1994 camry driver side p


Start with a good thick pair of leather gloves, a putty knife, and a tall trash can. Place the trash can below the mirror, tilt the mirror inward so you get a hold of the outer edge, and carefully pry the remaining pieces of mirror from the backing plate. Do not apply any pressure directly to the backing plate, or you may damage the gears on the electric motor. You should be able to pick up a new mirror and adhesive at your local auto parts store. Use masking tape and a couple of wood blocks to hold the glass in place while the adhesive sets (blocks against the glass, then wrap the whole thing in tape).

Feb 21, 2009 | 2003 Toyota Camry

1 Answer

Driver mirror


the mirror glass just pops ono a ball stud. 2 jack screws go in or out by tiny electric motors. 2 friction pins go into plastic holes to prevent vibration.

Removal
  1. Position the mirror glass to obtain a gap at the lower inboard edge of the mirror assembly.
  2. Disengage the power mirror motor jackscrews from the mirror backing plate.
  3. syj~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Place a shop towel between the mirror glass and the hand to avoid personal injury in the instance of glass breakage.
    Remove the mirror glass by grasping the outboard edge of the glass and separate it from the mirror housing.
    • If equipped, disconnect the electrical connector
  4. Remove the friction pins from the mirror backing plate.
8fee414.gif

Feb 20, 2009 | 2000 Ford Expedition

1 Answer

Side mirror inside glass hanging ford explorer


it depends on whats 'hanging', if JUST the mirror glass has come off it's plastic backing plate, then yes you can silicone it back into place. If the mirror glass AND the plastic backing plate are hanging, you can try to 'snap' the backing plate back into the mirror head but most likely something inside is broken and the mirror head will have to be replaced. for a better idea on reinstalling or replacing a mirror see: www.burcinc.com and for aftermarket replacement mirror heads see: www.directauto.com
hope this helps.

Feb 16, 2009 | 2005 Ford Explorer

2 Answers

How to remove mirror glass 2008 ford f350


here's 2003, don't have 2008

Removal
NOTE: Left-hand dual arm mirror with heat shown, non-heated and aero mirrors similar.
All exterior mirrors
  1. Position the exterior mirror glass in the full down position.
  1. Grasp the top and carefully pull the exterior mirror glass away from the mirror housing.
8157e6e.gif
  1. Disconnect the electrical terminals (if equipped) and remove the exterior mirror glass.
Power exterior mirrors
  1. Remove the jack pins from the exterior mirror glass backing plate.
    • Use pliers to grasp the jack pins at the base to remove.
429f568.gif
Installation
Power exterior mirrors
  1. Remove the sealing boots from the exterior mirror motor.
a8bd649.gif
  1. Install the jack pins in the sealing boots.
869a220.gif
  1. Install the jack pins and sealing boots.
    1. Hold the legs of the jack pins and push the jack pins back into the exterior mirror housing.
    1. Install the sealing boots so the boot shoulder is under the mirror collar and turn each jack pin until the head of the jack pin is aligned with the slots in the sockets on the backing glass plate.
95e6577.gif
All exterior mirrors
  1. Place the new exterior mirror glass assembly down on a smooth firm surface.
  1. Align the friction pins vertically to the exterior mirror glass backing plate socket and push down to snap the pivot ball into the socket.
52fef14.gif
  1. s3o~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not over heat the exterior mirror glass backing plate. Heat only until backing plate is warm to the touch.
    Using the special tool, warm the main pivot sockets in exterior mirror glass backing plate.
ed69017.gif
  1. Loosely install the glass.
    1. Connect the electrical wiring to the electrical terminals (if equipped).
    1. Position the friction pins in the mirror housing.
    1. Align the jack pin locating tabs to match with the mirror glass back.
  1. Using a flat hand, press on the center of the mirror glass until seated on the center pivot of the mirror housing.
    • Press the mirror glass toward one of the jack pins until snapped in place.
    • Repeat for second jack pin.
a10e39d.gif
Power exterior mirrors
NOTE: If the jack pins do not engage, they may not be aligned correctly. Remove the exterior mirror glass, align the jack pins to the slots in the sockets and repeat the installation procedure.
  1. NOTE: The jack pin should click while manually adjusting the exterior mirror glass.
    Tilt the exterior mirror glass to the full outboard position and then press on the outer side of the class until the in/out jack pin snaps into the socket on the exterior mirror backing plate.
  1. NOTE: The jack pin should click while manually adjusting the exterior mirror glass.
    Tilt the exterior mirror glass to the full down position and then press on the outer side of the class until the up/down jack pin snaps into the socket on the exterior mirror backing plate.

Nov 14, 2008 | 2008 Ford F-350

Not finding what you are looking for?
2007 Mercedes-Benz ML320 CDI Logo

Related Topics:

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...