Question about 1990 Mazda Protege

1 Answer

What size would my alternator belt be on my 1990 mazda ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 2,984 Answers

what size would my alternator belt be on my 1990 - mbh.gif Master Pro Belt/Hose - [V-Belt] Part Number: 9360

7b25ba4.jpg

This one is $4.99 at schuck's/chief's/kragen

Posted on Apr 23, 2010

Testimonial: "cheers mate will buy tomorow hope it rite befor i pull mine out hahaha.thanks :)"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maita charging problem


Rather than just replacing things, check that the alternator belt is properly tensioned first. If it's too loose and slipping you won't get proper output from the alternator. On the 90 you should only be able to press in at the center of the belt span about 3/8 of an inch.

If the belt looks OK, then get some testing done. I'm not sure if you're in the US but an Autozone or Advance Auto Parts store will connect a free diagnostic tester to the vehicle which can usually identify exactly what the problem is. Note that remanufactured alternators can often be defective right out of the box.

Aug 02, 2014 | 1990 Mazda MX-5

2 Answers

My 1990 dodge dakota keeps throwing its belt


If you are not using a new belt, go get a new one. Belts stretch out over time.

If you are using a new belt, look at the part number on the belt and write it down. Take that down to an auto parts store and ask them for a belt between half-an-inch to an inch smaller. Replacing your alternator bracket may have changed the position of the alternator pulley in relation to the other routing points. Since it is throwing the belt, the stock belt is now too large, and you should try the next size down.

Oct 25, 2012 | 1990 Dodge Dakota

1 Answer

Are the alternators for a mazda 323 and mazda protege the same?


According to my book, Protege and 323 are the same, but only 1990 and 1991 model years.

Jul 07, 2012 | Cars & Trucks

1 Answer

I have juct replaced alternator belt but now need to replace power steering/ aircon belt. is it ok to drive without for a short distance


It won't harm anything on a short drive. Remember that it will be much harder to turn the car especially in intersections so try to plan ahead. Hope this helps.

Nov 11, 2010 | 1990 Mazda 626

1 Answer

How to replace alternator for a 1995 mazda mvp


Don't know your engine size so pick the appropriate one:

MPV Models 2.6L ENGINE
Fig. 2: Alternator installation — 2.6L engine
0845f92.gif
  1. Disconnect the negative battery cable.
  2. Tag and disconnect the wire and connector from the alternator.
  3. Remove the drive belt.
  4. Remove the support mounting bolt and nut.
  5. Remove the alternator assembly. To install:
  6. Position the alternator assembly against the engine and install the support bolt.
  7. Install the adjusting strap mounting bolt.
  8. Install and adjust the alternator belt.
  9. Tighten the support mounting bolt to 28–38 ft. lbs. (38–51 Nm), and the adjusting bolt to 14–18 ft. lbs. (19–25 Nm).
  10. Connect all alternator terminals.
  11. Connect the negative battery cable.

Oct 06, 2009 | 1995 Mazda MPV

1 Answer

Belt between water pump & alternator squealed and popped off - di


You could have the wrong size or the serpentine belt was routed wrong. Double check the routing and the length of the belt, the other thing to that is know to happen is the belt tension pulley has gone bad and needs to be replaced. Recap, check the routing of the belt, belt length, tension pulley for any damage. Good luck and hope this helps.

Jul 16, 2009 | 2002 Mazda Protege

4 Answers

Alternator drive belt squealing


yeh, mine did the same thing with a hydralic belt. it was the bearings. mazda capellas use a lot of 6202 bearings which, luckily, are fairly cheap, and are commonly used in pool pumps. so you can find them at pool pump repair stores. although pool pumps use 6202 2RSR bearings. these are just the water proof type, but are excactly the same size and can be used.
to test if it is a bearing problem, remove the belt and try to twist the individual wheels by hand, you should be able to turn the 2 smaller ones.
from memory the alternator belt is in a fairly in accessable postition so the belt is going to be hard to put back on.try other things first, like wiping the inner side of the belt with a dry cloth to remove moisture.
worst case senario is your alternator has, or is starting to, seize up and you need to replace it.

Jun 08, 2009 | 1999 Mazda 626

1 Answer

Mazda 626 1990


Start by disconnecting the battery, remove the belt on the alternator,you will probably have to loosen or remove the bolts holding it on to the bracket, it makes it easier to get the belt off, pay attention to how you remove it, then get it tested, if its bad get a new one and install.

Feb 12, 2009 | 1990 Mazda 626

1 Answer

Loose fan belt.


What is the belt specification or size for the main belt that drives the water pump and alternator? Lost mine on the road.

Aug 04, 2008 | 1993 Mazda 323

1 Answer

Overheating -


its sound like our alternator belt broken that belt drive the water pump broken alternator belt charge light on belt dont turn water pump overheating dont drive with it check that out first thank you pierre

Aug 03, 2008 | 1990 Mazda MX-5

Not finding what you are looking for?
1990 Mazda Protege Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...