Question about Ford Ranger

1 Answer

I have a 1984 ford ranger xlt 2.8 v6 manual transmission, I have put a new lock cylinder and new ignition switch but it will not shut off with the key. (carburated)

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

Sounds like you have a broken ignition lock actuator in the column. You can get these aftermarket. It is a common problem.

Posted on Apr 23, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Both coils do not fire on 1 and 4. Will start but only running on 2 cylinders. Could both coils be bad or should I look elsewhere?


Part 3 -How to Test the Ignition Module and Crank Sensor ...

easyautodiagnostics.com > Ford > 2.3L
Mar 1, 2012 - Spark plugs for cylinders #2 and #3 get spark at the exact same time. ...voltage -12 Volts) to both individual ignition coils within the coil pack. ... Ford Mustang or Ranger (or 2.3L Mazda B2300), this is what you'll need ... for this 'Switching Signal' at the coil pack... but you can also test this ... 1991, 1992, 1993.

How to Diagnose a Misfiring Cylinder (2.3L Ford Ranger ...

troubleshootmyvehicle.com > Ford > 2.3L
Apr 3, 2012 - Bad Fuel Injectors can cause a Misfire Condition. ... the ignition system on the 2.3L Ford Mustang or Ranger consists of 2 ignition coil packs, ...

2002 ranger misfire rough idle - Discussion on Topix

www.topix.com > Ford Ranger
Jul 27, 2007 - My truck is giving the code misfire in number 4 cyl. I replaced my spark plugs, Wires, Coil packs (both of them) and all my fuil ... three (3.0L v6) go bad, the fuel/air mixture gets messed up. Judged: 2. 2 ... My truck runs rough only at idle. ...code for ford ranger 2002, 2.3 5speed. truck runs like a champ but that ...

Extremely stumped! I need the best and brightest 1994 Ford ...

answers.edmunds.com > Edmunds Answers

Jan 31, 2016 | Cars & Trucks

1 Answer

Why is my ignition switch sticking?


You could try graphite in the cylinder, but it is a common problem on older Fords, usually resulting in changing the lock cylinder,

Aug 24, 2014 | 1992 Ford Ranger

1 Answer

I have no key to my 1993 ford ranger xlt 4.0 Auto 2wd Ignition switch removal and Installation


In most cases you will have to drill it.
There are videos on Youtube that show how its done.
Most all Ford locks in the late 80s and early 90s are the same style.

Aug 03, 2012 | Ford Cars & Trucks

1 Answer

M5odr1 2.3 to 3.0?


Check to see if the trans codes match from the VIN or the Ford manufactures plate on the drivers side door jam on both trucks.

Jun 18, 2012 | 1995 Ford Ranger Supercab

1 Answer

How do i change ignition switch on my 19890 ford ranger xl 4x4 2.9L V6


Rotate the lock cylinder to the lock position. On tilt columns, remove upper extension shround by squeezing at 6 and 10 o'clock and popping free of the retainer plate at 3 o'clock.

Remove 2 shroud halves by removing the screws. Disconnect the electrical connector from the ignition switch. Drill out the 2 break-off bolt heads that hold the switch to the lock cylinder using a 1/8" drill bit.

Remove bolts (may have to use a screw extractor). Disengage ignition switch from actuator pin and remove switch.

To Install:
Rotate the key to the run position. Install switch by aligning holes on switch base with hole in the cylinder housing. You may have to move it a little to get the actuator pin to line up.


Install new break-off bolts untill the heads shear off. Connect electrical connector to switch.Then reverse the removal procedure to complete.

Mar 19, 2011 | 1989 Ford Ranger

1 Answer

91 Ford Ranger XLT, 4 cyl, manual 5 spd. Engine


most likely right on top of steering colum around have way down

Oct 07, 2009 | 1992 Ford Taurus

3 Answers

Where is the ignition module control located on 1996 ranger 2.3 e


It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Apr 08, 2009 | 1996 Ford Ranger SuperCab

1 Answer

Clutch fluid


I would first check for leaks, and if no leaks i would check your master and slave cylinders if they are working properly

Dec 17, 2008 | 1993 Ford Ranger SuperCab

2 Answers

93 Ford Ranger Ignition Cylinder


Hi..
On 1993 Ford ranger to remove the ignition lock cylinder switch

You need to remove the Steering wheel.
Remove trim shrounds.
Set ignition switch to Run position.
If your vehicle is A/T trans. put the selector lever in Park.
You will see retaining pin. Push retaining pin inward and pull out the lock cylinder.
Unplug wire from lock cylinder.
To install reverse remove procedure.

NOTE'' If you don't have the key or the cylinder is locked.
Instead of push the retaining pin you will need to Drill with a
1/8 in ( 3.17mm) Bit to drill out the retaining pin.
Be careful DO NOT drill more than 1/2 in deep.
After you need a chisel to break away the cylinder cap.
You need a 3/8in (9.52mm) bit to Drill in center of the cylinder.
Drill aprox. 1 3/4 in( 44mm) Deep.
REmove metal shavings. And remove the cylinder.
Clean and lubricate the gear inside. and install the new cylinder.

OK............I hope this information work for you.
Thank's for use fixya.

Jul 13, 2008 | 1993 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...