Question about 1997 Jeep Wrangler

1 Answer

Engine diagram 1997 jeep wrangler SE

I need to replace the oil pump in my 1997 jeep wrangler SE 4 cylinder but don't know where it is. Looking for a diagram or directions how to do it. Trying to do it myself to save money.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

So how do you know you need one if you dont know where it is?? Oil pumps rarely go bad unless the engine is sludged from lack of maintenence. After you take the oil pan off, its there hanging down. Make sure you clean or replace the pick up tube. I'm sure you can google up torque specs, for the bolts. Usually there is major engine damage by the time you figure out that there is lack of oil pressure. I would get a professionals opinion before you waste time and money replaicing the oil pump. If the engine has any unusual noise or knocking, its too late.

Posted on Apr 23, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need routing diagram for serpentine belt - '98 Jeep Wrangler, straight six with and without A/C


Click of the following direct, Free Link. It has several Serpentine Diagrams, including the one for your 1998 Jeep Wrangler 4.0L In-Line 6-Cylinders based upon your Engine Options (AC/No AC, Power Steering/No Power Steering, etc.).
The Link Page ALSO has the 2.5L In-Line 4-Cylinder Serpentine Belt Diagrams with their various engine options.
Included are the with AC / without AC Routing.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!
http://www.2carpros.com/car_repair_information/year/1998/make/jeep/model/wrangler/1998_jeep_wrangler_drive_belt_routing_diagram.htm

Apr 13, 2010 | 1998 Jeep Wrangler

1 Answer

Describe your 1997 Jeep Wrangler 1997 jeep wrangler 4 cyl idle fluctuates 900 rpm to 400 rpm after warmup no service engine light but check guages light comes on momentarily when rpm gets low and oil press...


The check gauges light is normal because at 400 rpm it isn't running fast enough to build sufficient oil pressure. I am guessing maybe a vaccum leak???

Jul 10, 2009 | 1997 Jeep Wrangler

3 Answers

Oil pressure gauge drops after running and sitting still


oil pump going, or the crank bearings worn.
are there any noises that appear when oil pressure drops?

check sensor

Jul 01, 2009 | 1998 Jeep Wrangler

1 Answer

Oil pan removal on a 97 jeep wrangler


Instructions can be found in any basic manual but the simple version is to remove anything obvious that will be in your way (starter, trans lines etc). Disconnect both engine mounts and raise engine to get better clearance (watch stuff on top so you don't break anything) I usually stuff a couple of 2x4 wood blocks between engine & mounts to support it. Remove all pan bolts and take it down (remember pump pickup will interfere) Do what you need to do, then reverse process.

Jun 12, 2009 | 1997 Jeep Wrangler

1 Answer

95 jeep wrangler: gauge indicates 0 oil pressure


Wire on oil sending unit may have fallen off or sensor itself may have gone bad. Check both. If engine has no tapping noises, likely it's not a pressure problem.

Jun 07, 2009 | 1998 Jeep Wrangler

2 Answers

Jeep Wrangler oil pan leak


You need to Put Blue ATV Silicone on Both sides of the Gasket to get it to Seal Properly. This is a High Temp Sealant and Once Set it will fix the Problem.

Jan 26, 2009 | 1997 Jeep Wrangler

Not finding what you are looking for?
1997 Jeep Wrangler Logo

881 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...