Question about 1998 Ford Windstar

1 Answer

How to replace a oxygen sensor in a windstar 3.8l

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 238 Answers

You need to know which one, a 98 windstar has four. The actual labor is simply unpluging the sensor and using a 7/8 wrench to unscrew it from the exhaust pipe.

Posted on Apr 23, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My check engin light came on the codes came up as po133, p1000 what do i do to fix my car is a 1998 ford windstar?


A code P0133 may mean that one or more of the following has happened:
  • The oxygen sensor is faulty
  • The wiring to the sensor is broken / frayed
  • There is an exhaust leak
the problem is more than likely the front Bank 1 oxygen sensor. You will likely wind up replacing it but you should also consider these possible solutions:
  • Check and fix any exhaust leaks
  • Check for wiring problems (shorted, frayed wires)
  • Check the frequency and amplitude of the oxygen sensor (advanced)
  • Check for a deteriorating / contaminated oxygen sensor, replace if necessary
  • Check for inlet air leaks
  • Check the MAF sensor for proper operation
  • code p1000 refers to emission monitors not fully run and requires a couple of drive cycles from cold start to fully warmed drive cycle at different speeds.

Oct 10, 2014 | 1998 Ford Windstar

1 Answer

Where is oxygen sensor 1999 windstar?


The oxygen sensors are located under the vehicle on the exaust manafold unless you are getting a certain code wich u should be getting if they are malfuctioning then it could be something else.have you change the fuel filter? It also might need a tune up new plugs wires air filter ext

May 05, 2014 | 1999 Ford Windstar

1 Answer

Oxygen sensors


Please what is your engine size 3.0l or 3.8l

Nov 23, 2013 | 1999 Ford Windstar

1 Answer

Oxygen sensors


Replacing is the only way I know of to correct a problem. You could buy used sensors.

May 30, 2013 | 1999 Ford Windstar

1 Answer

Winstar stalls


check fuel filter fuel pump pressure

Feb 03, 2012 | 2003 Ford Windstar

1 Answer

How do i buy online the oxygen sensors for a 2001?


The oxygen sensor are just refered to as upstream for the o2s and down stream are actually refered to as catalytic monitors. So if you have lean or rich codes these would refer to the upstream .

May 30, 2010 | 2001 Ford Windstar

1 Answer

Change oxygen sensor 2001 ford windstar


fist unclip wire,then unscrew it with a 28mm spanner ,fitting procedure is the reverse .It turns anticlockwise to unscrew and clockwise to screw up ,torque setting is a grunt and two scuffed knuckles and max of 3 swear words

Jan 01, 2009 | 2001 Ford Windstar

1 Answer

Truck codes p1132 and p1152


Hi,

P1132 = Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Rich - Bank No. 1
P1152 = Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Rich - Bank No. 2

It sounds to me like the oxygen sensors (between the engine and catalytic converters) should be replaced. Good luck!

Dec 21, 2008 | 2000 Ford Windstar

1 Answer

Oxygen sensors


you have 3, 2 upstream and one downstream. They have wire harnesses attached to them and they screw into the exhaust system. Ususally two in the exgaust crossover pipe, the other just behind the catalytic converter.

Oct 03, 2008 | 2002 Ford Windstar Cargo

Not finding what you are looking for?
1998 Ford Windstar Logo

Related Topics:

398 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...