Question about 2005 Suzuki Verona EX

1 Answer

Need to replace rear wheel stud - 2005 Suzuki Verona EX

Posted by on

  • fishinggreg Apr 22, 2010

    I need to know how to get the rotor off so I can remove the stud?

  • fishinggreg Apr 22, 2010

    I need to know how to remove the rear rotor on a 2005 suzuki verona?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,865 Answers

Hello. Here is a link to explain step by step how to remove that stud. Joe http://www.ehow.com/how_5484703_remove-broken-wheel-studs.html

Posted on Apr 22, 2010

  • Joe Hogan Apr 22, 2010

    Regards, Joe

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a rear wheel stud


remove the wheel
using a hammer and punch knock the broken stud out
fit the new stud from behind use over size nuts as spacers fit the stud nut and apply tension
using the hammer and punch from the rear on the head of the stud knock it in as you keep the tension on the stud nut
keep the process going until the stud is fully seated on the head of the stud

Jul 10, 2014 | 2005 Toyota Camry Solara

1 Answer

Removing rear wheel studs


there should be one spot while turning rear wheel bearing that will allow one stud to be knocked out and new stud replaced BEFORE trying to remove the next stud... one at a time

May 16, 2014 | 2008 Chrysler Aspen

1 Answer

2001 altima replacing rear wheel stud


strip it down to your hub the hub holds the studs .it is a push pull fit .but an old nut on it.then hit the top of it .it when then push in.remove the nut. push in the new stud from the rear of the hub.put a larger nut on top of stud ,then your wheel nut to pull the stud into the hub.then remove the wheel nut .then refit the parts taken off.and fit your wheel.

Dec 30, 2013 | 2005 Chrysler PT Cruiser

1 Answer

Broken wheel studs on a 1987 jeep wrangler


No need to replace the hub just the studs. The come in from the back and are splined to prevent the stud from turning with the nut. Remove the hub --drive out the broken studs and put the new ones in from the rear and drive them back in. Get the studs from the dealer spares or a good tyre retailer.

Apr 08, 2013 | 1987 Jeep Wrangler

1 Answer

How do I replace the rear wheel studs on a 2006 Mercury Mountaineer


take off wheel and hub use hammer tap them out from front replace / insert new one in hole tap back in u will have to turn axle to desired location to get new one in

Sep 03, 2012 | 2006 Mercury Mountaineer

1 Answer

How to get drum pads off a 2000 dodge caravan


The pad drums of your 2000 Dodge Grand Caravan can wear with use. Heat buildup in the brakes can glaze, warp or crack the drum. If that happens, replacement of the drum is the only way to fix it. In most cases, you can remove the rear drums, replace them with a new set and leave the existing shoes on the van. Take a minute and inspect the brake shoes thoroughly while you have the drums off the van.


  1. Loosen the lug nuts on the rear of your 2000 Dodge Grand Caravan with a lug wrench. Do not take them off the wheel studs.
  2. Raise the rear of the van with a jack and support it on a set of jack stands. Place the stands under the rear suspension, making sure they are secure. Remove the lug nuts from the wheel studs and pull off the rear wheels.
  3. Check the rear drum where the wheel studs come through for retaining clips. These are used during the manufacturing process; and if they are still on your van, they need to be removed. Pry the clip off the wheel stud with a flat head screwdriver and discard them. Most vehicles will have two clips on each brake drum.
  4. Grasp the brake drum on the outer edges and pull it straight off the wheel studs and brake pads. Discard the old drum and slide the new drum into place, aligning the holes in the drum with the wheel studs. Push the drum in until it seats completely. Repeat the process on the opposite side of the van.
  5. Position the wheel back on the wheel studs and install the lug nuts by hand. Raise the back of the van with a jack and remove the jack stands from under the suspension. Lower the van to the ground and tighten the lug nuts with a lug wrench.

Jan 08, 2011 | 2000 Dodge Caravan

3 Answers

How to change broken stud on rear axle 1997 ford explorer


I am assuming you are talking about a wheel lug stud. The lug studs are pressed in from the inner side of the drum or rotor or axle flange depending on how your vehicle is equipped. You have to remove the wheel and drum or rotor to get access to the back side. Drive the broken stud out from the front after you have removed the drum or rotor and set the new one in from the back and tap it into the hole until set as the rest are. If you cant get it set all the way you can finish setting it by pulling it into place when you tighten the lug nuts on reassembly. The part should be under $10.00

Nov 18, 2010 | 1997 Ford Explorer AWD

1 Answer

How do u fix a rear stud on a 1999 Nissan Maxima


You will need to remove the Rear Wheel, Brake Caliper, and Rotor to replace the Stud. Once those are removed, take a Hammer and hit the Wheel Stud from the front to drive the Stud out through the back of the Wheel Hub. Once the Stud is out, take the new Stud and insert it in the Hub from the back. You will need to get a Open Ended Nut with the proper thread size as the Stud and thread it on the Stud, and tighten the Nut till the Stud comes all the way through the hole and the end of the Stud is flush with the back of the Hub. Remove the Nut and you can now put everything back together.

Jul 15, 2010 | 1999 Nissan Maxima

1 Answer

How to change stud in rear wheel hub assembly. i need to know how to change the stud in the rear wheel hub assembly, and how do i go about taking it apart


Remove tire and wheel, remove caliper and brake rotor. DO NOT apply the brakes while the caliper is loose. Hit stud you want to replace hard with a LARGE HEAVY hammer to drive it out towards vehicle. DO NOT use a light hammer. It will distort the stud and possibly mushroom the end making it very difficult to remove. Once the stud is loose, you may or may not have enough room to get it out of the hole. You may need to pull the hub loose from the rear suspension to gain more room. Remove the stud. Place new stud in hole. Put a stack of washers over the stud, grease the threads, and using a new FLAT nut with the same threads as the lug nut, tighten until the stud is pulled all the way into the hub. Remove the flat nut, reattach the hub assembly (if you needed to take it loose) and reinstall the brakes.


Sep 28, 2009 | 1994 Ford Probe

1 Answer

Broken rear wheel stud on a 2005 ford focus zx4 se


  1. Step 1 Buy a new stud. Make sure you purchase the right size. If you're not sure what size to get, wait until you remove the stud and take it with you to the store.
  2. Step 2 Check the area of the spare tire in the trunk for the jack and the jack tools since you'll need to raise the car to replace the wheel stud on your Focus. Be sure to block the tire diagonal to the jack.
  3. Step 3 Use the jack to raise the Focus. Remove the wheel Take off the caliper and either hang it by a mechanics wire or lay it up so it doesn't dangle by the brake line. Remove the rotor. If you're working on back wheels, you have to remove the emergency brake clip first. You could have drum brakes in the rear. If they're drum brakes, remove the drum.
  4. Step 4 Hunt for an opening behind the hub that allows you to remove the stud. Line the stud up with the hole. You may have to take off the hub and put it in a vise if you can't drive it out the back.
  5. Step 5 Hit the stud with a mallet and drive it out the back of the hub. Push another stud into the opening. This is tough work, but you only need to push it far enough to thread on a wheel bolt.
  6. Step 6 Put on a wheel bolt and begin to tighten it. As you do, the stud starts to pull through. Add more bolts as necessary until you seat the stud. Check in the back of the hub. When the head is flush with the stud, you seated it.
  7. Step 7 Remove the extra bolts and reassemble the parts that you took off to replace the wheel stud on the Ford Focus. Put the wheel back on the vehicle and tighten down the wheel nuts.

Sep 25, 2009 | 2005 Ford Focus

Not finding what you are looking for?
2005 Suzuki Verona EX Logo

257 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...