Question about 1993 Toyota Pickup

2 Answers

My clutch pedal will not return to the up position after I press in to change gears. Advice?

Posted by on

  • Zaraki May 11, 2010

    Does it have a hydraulic clutch? If it does check the fluid level in the clutch master cylinder.

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Toyota Expert
  • 178 Answers

If you don't see any leaks try pulling the rubber boot off of the
cylinder that the clutch pedal pushes on. That's where the leak
was on my '87 and the boot kept the fluid from leaking any further so it was hard to find.

Posted on May 17, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 98 Answers

Strange one but if you havent done it yet. check the clutch fluid.
under the hood near the brake fluid

Posted on Apr 22, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch pedal sitting on floor/no return.


It may be the clutch assy. but before I did that I would check the cable out as it seems strange the pedal would stay on the floor even if the clutch went out. There should be a return spring on the pedal.

Jan 09, 2016 | Cars & Trucks

1 Answer

Revs high when i change gear


Is it possible the clutch pedal is interfering with the throttle? Start the engine in neutral and allow it to idle. Press only the clutch pedal down and see if this increase the engine speed. If it does speed up the engine and slows back down when you release the clutch then somehow this operation is where your fault lies. If it doesn't alter the idle speed, then rev your engine and release the throttle to see if it returns to idle immediately. If it is slow to return to idle then your throttle cable could be sticking. This means when you change gear lifting off the throttle has little effect and depressing the clutch to change gear causes the engine to race as the throttle is still partially open.

Aug 23, 2014 | 2005 Ford Fiesta 1.3

1 Answer

Sticky clutch pedal return


lubricate clutch pedal at pivot points

Dec 28, 2013 | 2001 Audi A4

2 Answers

Gears won't change. Can anybody provide some useful advice. ?


Automatics have a gear shift safety solenoid that locks the gearshift/transmission in park unless the brake pedal is depressed. This is to prevent people from dropping into a gear from park and rolling into traffic or backing up over someone unexpectedly. When you press the brake pedal you should be able to hear a clicking sound coming from under the gear shift lever. If you dont hear the sound then the solenoid may need to be replaced. The other possibility is needing to replace the brake pedal position switch (usually attached to the pedal assembly or behind the brake pedal assembly) which tells the shifter solenoid to activate when the pedal is depressed.

Apr 10, 2013 | Cars & Trucks

1 Answer

While driving on the road upon changing gears the clutch pedal sticks to the floor


try greasing or replacing the fulcrum of the pedal shaft. this may have got corroded inside which makes it difficult for the pedal shaft to return to its original position by the action of the return spring.

Jun 29, 2011 | Toyota Prius Cars & Trucks

1 Answer

Clutch pedal not returning to position


Under the dash look to see if there is a spring attached to the petal or maybe under the hood. Or you might have something getting in the was of the petal arm. Good Luck and PEACE

Jun 13, 2008 | 1987 Ford F 150

Not finding what you are looking for?
1993 Toyota Pickup Logo

263 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...