Question about 2003 Ford Excursion

1 Answer

Truck is turned on and running, begin to drive,

Truck was turned on and running, begin to drive, the engine begins to start chugging I pull over to let truck idle , truck engine dies and now won't crank over at all, no noise, nothing, all gages respond, all lights are bright, fans work, checked connection of batteries still nothing

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Do you need oil do you got gas write back and ill tell you exactly wat to do

Posted on Apr 22, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What could be wrong with my Toyota Echo if the engine chugs while idling, and the car loses power when accelerating (stalling out if accelerating too quickly)?


There are numerous things that will cause this problem. If the check engine light is on, have the codes checked to see if there is a problem the computer has found to cause this issue. Even without the check engine light on, there may be a code stored. You can also do a visual inspection under the hood for any disconnected hoses causing vacuum leaks. These are the best places to begin with diagnostics

Aug 03, 2015 | 2003 Toyota ECHO

1 Answer

Trouble starting keeps running after turning it off


If it is chugging and running rough after you turn the key off, it may be "dieseling" which is caused by carbon buildup in the cylinders and the idle speed being higher than spec. Pulling the coil wire from the coil and the engine continues to run is a good example.

Aug 26, 2012 | 1991 Ford Ranger Supercab

1 Answer

Engine failure


When a catalytic converter is coming apart on the inside, it can restrict air flow and power, and it usually happens or gets worse when the vehicle has been running long enough to generate a lot of heat. Once it cools down, the symptoms can completely go away until you begin to drive it again. It's one possibility.

Jun 19, 2012 | Cars & Trucks

1 Answer

Truck engine slows to idle. reduced engine power reads across instrument panel and engine light comes on. turn engine off for a few seconds and engine will run fine for a while.


This is the beginning of the bad Crank Shaft Sensor. The engine can die any time during the run, and not start until 2 hours later.
Run a diagnose with a scan tool to find out what the engine code is to confirm. Good luck.

Nov 20, 2010 | Chevrolet Silverado 2500HD Cars & Trucks

2 Answers

My truck began to stall and quickly lose engine power as I was driving yesterday. I can turn the engine on but, it instantly turns off again especially when I try to rev the engine. What could the p


You could have a dirty Fuel Filter, try changing that first since it's the easiest and cheapest to do. You'll find the filter i believe on the inside if the frame under the drivers area. The only other thing i can think of is a fuel Pump going bad and not producing enough fuel pressure.
Best thing, start with the fuel filter and get the truck scanned for any DTC codes.
Good luck and hope this helps.

May 08, 2009 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Chugs, acts like it's not getting gas once warmed up. Idle's fine


This problem can be several things. When your engine is cold, your computer is in a "closed loop" and just pretty much keeps the engine running until warmed up. After reaching operation temperature, the computer starts reading all the sensors. If one sensor is not connected or is defective, you will experience performance problems. Most of the time this will turn on the check engine light, but not always. Second is the fuel pump. This too will cause erratic engine problems.

Apr 10, 2009 | 1991 Chevrolet Silverado 2500

1 Answer

Engine Missing / Hesitation Cold Weather


run the fault codes
check for problem ambient temp sensor, baro sensor , maf/vaf sensor problems

Apr 07, 2017 | 2002 Chevrolet Silverado 1500

3 Answers

Engine first runs good, but progressive chug/misfire.


Check for vaccum leak, if not check or replace mass air flow sencor.

Nov 28, 2008 | 1993 Mercury Villager

1 Answer

Ser.eng.soon flashes code 34 MAP sensor


A code 34 calls attention to the MAF sensor, not a MAP sensor. Try changing that out, first. You might also be having problems with your ignition control module.

Jul 20, 2008 | 1988 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
2003 Ford Excursion Logo

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...