Question about Dodge Dakota

1 Answer

I gotta 89 dodge dakota with a blower motor out, i changed the resistor and now looking to change out the blower motor it self, where and how do i get it does the whole dash need to come out or just underneth?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 312 Answers

Study from in the engine area to see if you have any chance of pulling from there if not then you will need to get under the dash in the area of the motors. From the engine compartment you will be able to see where the motor is so you can pull the cover in that area inside. Good Luck those can be a challenge in some vehicles.

Posted on May 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

A//c unit works only on high speed/


blower motor resistor...it cuts power to lower settings...easy fix usually under passenger side glovebox two screws and harness looks like a metal card with plastic bottom...

Jan 28, 2016 | 2004 Dodge Dakota

2 Answers

Where is the heater resistor on a 2005 dodge dakota? Behind glove box?


should be just above the blower motor. You will need to remove the glove box door to gain access.

Dec 12, 2015 | 2005 Dodge Dakota Club

1 Answer

2001 dodge dakota keeps burning up blower motor resistors and I have changed the blower motor would it be a bad ground and where do I look? Truck has a few other electrical problems


Check the alternator output voltage. It sounds like the voltage regulator is bad. A bad ground would not complete the circuit so no fan at all or a slow turning fan due to no or low voltage. A bad ground will not burn up the speed resistor

Nov 15, 2015 | Dodge Cars & Trucks

1 Answer

My blower motor on my 2000 Dodge Dakota does not work sometimes. On occassion if I bang the under side of the passenger side dash board it will work. I have changed the relay under the hood and still no...


There is a resistor in the box that controls fan speed. That resistor can melt the wires making the circuit.
My 94 Dakota has this resistor on the firewall. Yours may be under the dash.
You may also have a faulty fan switch. It is also possible to have problems with the brushes inside the motor.

Jun 29, 2012 | 2000 Dodge Dakota Quad Cab

1 Answer

I have a 2003 Dodge Dakota the ac blower motor quit working. I found burnt wires up under where the glove box is close to the blower motor. Looks life going to some type of module. How do I fix the blower...


Those wires are likely going to blower resistor. Try replacing the blower resistor, and replace connectors on wires to it from blower motor. You just might get lucky. (blower resistor is what regulates blower speeds)

Jul 16, 2011 | Dodge Dakota Cars & Trucks

2 Answers

Hi ya, i just inquired about my blower motor, is the relay and switches and everything under the dash or under the hood,


In the Dodge Dakota the blower motor resistor is located under the hood, on the right side firewall.

Dodge Dakota Blower Motor Resistor Location:

b3bc94a.jpg

Dodge Dakota with a complaint of no blower operation. After unplugging the harness connector and removing the two screws, you could remove and examine the resistor coils for damage. The heat and subsequent rust damage are clearly visible in the picture below.

6f6f301.png

Apr 07, 2010 | Dodge Dakota Cars & Trucks

1 Answer

I changed the blower motor resistor pack, and the blower still doesn't work. what do i look for next?


Have you applied 12 volts DIRECTLY to the motor ?
I have the parts you need and step by step instructions on how to check motor and replace, IF that is the problem.
www.aescompaniesllc.com
Please click on the contact.

Feb 12, 2010 | 2003 Dodge Dakota Club Cab

1 Answer

Blower motor wont come on


Replace the blower resistor. The control head provides a ground circuit through the resistor block which reduces current flow to the blower motor which in turn gives you the different blower speeds.

Aug 29, 2009 | 2001 Dodge Durango

1 Answer

1997 Dodge Dakota 2WD with A/C. 135000 miles. Blower fan stopped working after a period of working intermittently. How do I replace it? It seems to be buried behind the dash and the ventilation air...


Wait, before you change that blower motor try replacing the blower motor resistor.It is located on the fire wall on the passanger side, under the hood. Should cost about 10 to 12 dollars and take about five minutes.Dakota's seem to go through these regularly.

Dec 10, 2008 | 1997 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...