I HAVE A '06 SILVERADO 1500 HD 2-WHEEL DRIVE, HOW DOES THE REAR PADS COME OFF THE CALIPER WITHOUT REMOVING THE SLIDE HOUSING?

You will have to pry the pads apart at the top of the caliper. The caliper should slide out now. If not, there is a spacer where the pins went through, sometimes they may get coroded and won't sline in the rubber. Shoot a little " liquid wrench" in and work them loose.

forst you will remove the two bolts that hold the caliper to the caliper bracket. With the caliper removed you can then use an 18mm socket and a breaker bar to remove the two bolts that hold the caliper bracket to the axle. These two bolts have threadlock on them and can be a real bear to remove. I have broken more than a couple wrenches and sockets removing these. Once the caliper bracket is removed you will then be able to remove the rotor. A hammer may be needed to break it free from the hub.

Pay particular attention the the caliper bracket and the area where the pad mounts to it. if you look under the abutment clips you will usually find a lot of rust which will cause the pads to bind in the bracket. Cleaning the rust out of this area and apply a little high temp anti sieze compound and your new pads will last a lot longer.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Brake Pads Removal & Installation Front

To Remove:

1. Drain brake fluid to ½ full level in reservoir.
2. Remove the front wheels.
   
   
3. Remove the front brake caliper assembly.
4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
5. Remove the wear indicator from each of the 2 brake pads.

To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.

1. Using a large C clamp or equivalent press piston into the caliper.
2. Apply disc brake grease to the inside of each anti-squeal shim.
3. Install the anti-squeal shims on each pad.
4. Install the pad wear indicator clip to the pads.
5. Install the pads with the pad wear indicator plate facing upward.
6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
7. Install the front wheels.
8. Fill the master cylinder with new clean brake fluid.
9. Pump the brake pedal several times to seat the brake pads.

Rear TMC made rear brake components

TMMK made rear brake components

To Remove:

1. Drain the brake fluid to ½ full level in reservoir.
2. Remove the rear wheels.
3. Remove the caliper slide pins.
4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
5. Remove the rear brake calipers.
6. Remove the 2 brake pads with the anti-squeal shims.
7. Remove the anti-squeal shims and pad wear indicators from brake pads.

To Install:

1. Using a large C clamp or equivalent press the piston into the caliper.
2. Coat both sides of the outer anti-squeal shim with pad grease.
3. Install anti-squeal shims to each pad.
4. Install wear indicators on the 2 brake pads.
5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
7. Fill the master cylinder with new clean brake fluid.
8. Pump the brake pedal several times to seat the brake pads.
9. Install the rear wheels.

Brake Rotor Removal & Installation Front To Remove:

1. Remove the front wheels.
2. Remove the front brake caliper assembly.
3. Remove the front brake pads.
4. Remove the 2 bolts and caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the front wheel disc.

To Install:

1. Align the match marks and install the front disc.
2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the front wheel.

Rear To Remove:

1. Remove the rear wheels.
2. Remove the brake caliper assembly.
3. Remove the brake pads.
4. Remove the 2 bolts and the caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the rear disc.

To Install:

1. Align the match marks and install the rear disc.
2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
   • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
   • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the rear wheel

The brake rotors are warpped [ the pulsation ], The pads may be worn out, and-or have a frozen caliper causing the loss of braking power.

Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly









4.0L and 4.7L front disc brake assembly




To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Front wheel
     
   • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
     and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.

1. Remove a small amount of brake fluid from the master cylinder.
   
2. Install a used brake pad into the caliper and compress the caliper pistons.
   
3. Apply disc brake grease to both sides of the inner anti-squeal shims.
   
4. Install or connect the following:
   
   
   
   • Anti-squeal shims to the new brake pads
     NOTE: When replacing worn pads, the anti-squeal shims must be replaced
     together with the pads.
     
     
   • 2 brake pads
     
   • Anti-rattle spring and the 2 caliper pins
     
   • Clip
     
   • Front wheel
   
   
5. Depress the brake pedal several times to seat the brake pads.
   
6. Check the brake fluid level and top off as needed.

Rear
To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Rear wheel
     
     
     
     
     
     
     
     
     
     
     
   • 2 cylinder slide pins from rear caliper assembly
     
   • Caliper assembly from rear caliper mounting
     
   • 2 brake pads with anti-squeal shims from rear caliper mounting
     
   • 2 anti-squeal shims from each disc brake pads
     
   • Pad wear indicator plate from the inner side disc brake pad
     
   • 4 pad support plates from the rear caliper mounting

To Install:

1. Install or connect the following:
   
   
   
   • 4 pad support plates on the rear caliper mounting
     
   • Pad wear indicator plate on the inside brake pad
     Note: Install the pad wear indicator facing downward.
     
     
   • Anti-squeal shims on each brake pad
     
   • 2 disc brake pads with anti-squeal shims to the caliper assembly
   
   
2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
   pins.
   
3. Install or connect the following:
   
   
   
   • Disc brake caliper assembly with 2 caliper slide pins
     
   • Torque to 65 ft-lbs (88 Nm)
     
   • Rear wheel
   
   
4. Depress the brake pedal several times to seat the brake pads.
   
5. Check the brake fluid level and top off as needed.

--- Removal & Installation
Front
To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Front wheel
     
   • Front brake caliper assembly
   
   
3. Make matchmarks on the disc and the axle hub.
   
4. Remove the front disc.

To Install:

1. Align matchmarks and disc onto axle hub.
   
2. Install or connect the following:
   
   
   
   • Front brake caliper assembly with the 2 bolts
     
     
     
     1. Torque to 90 ft-lbs (123 Nm)
     
     
   • Front wheel

From pads may be low causing the rear brakes to over brake and the anti-lock kicks in. Could be a sticking caliper piston and last the proportioning valve may need bleeding as it is offset.....

remove the BOTTOM 15mm caliper bolt lift the caliper up and slide off
then remover the 2 15mm bolts holding the caliper housing on
remove the brake rotor (you may have to hit it with a hamer to break it free
depending on the brake pads you got some come with new sliders
remove the sliders clean the rust build up then install new sliders
lube the sliders install the pads
install new rotor
install the caliper housing with the 2 15mm bolts
install the caliper and lube both caliper pins with silicone lube
install wheels
PUMP THE BRAKE PEDAL TILL IT GETS HARD WITHOUT ENGINE RUNNING

If you have disc brakes then these are easy. You need to take off the wheel of course. Then there are two bolts that hold your brake calipers on that you will need to take out. Then you slide the whole caliper off, and take the brake pads off. Then you need a fairly large C-clamp to push back the middle section of the caliper. After it is pushed in all the wall, slide the new pads on, they just click right in, grease the metal sliders a little bit and slide the caliper back on and put the two bolts back in and the wheel back on.

This is for the front: Removal & Installation

1. Remove 2/3 of the brake fluid from the master cylinder.
   
2. Remove or disconnect the following:
   
   • Wheel
     
   • Caliper. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
     
   • Caliper mounting bracket bolts
     
   • Caliper mounting bracket from the steering knuckle assembly
     
   • Brake pads from the caliper mounting bracket
     
   • Clips from the inside ends of the caliper mounting bracket and discard
     

To install:

1. Install or connect the following:
   
   • Clips to the inside ends of the caliper mounting bracket
     
   • Brake pads to the caliper mounting bracket
     
   • Inner pad (1 wear indicator)
     
   • Outer pad (2 wear indicators)
     
   • Caliper mounting bracket to the steering knuckle assembly
     
2. Perform the following procedure before installing the caliper mounting bracket bolts:
   
   • Remove all traces of the original adhesive patch.
     
   • Clean the threads of the bolt with brake parts cleaner or the equivalent and allow to dry.
     
   • Apply red Loctite®272 to the threads of the bolt.
     
3. Install or connect the following:
   
   • Caliper mounting bracket bolts to the steering knuckle. Tighten the caliper guide pin bolts to 74 ft. lbs. (100 Nm) on 15 series or 80 ft. lbs. (108 Nm) on 25/35 series.
     
   • Caliper
     
   • Tire and wheel assembly
     
4. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly in order to seat the brake pads. Burnish the brakes as needed.
   

if your pads are new, it could be the one making the noise! in time it will go off, pads is still fitting itself to the worn part of the metal plate/shim!