I only have high beam headlights. I have replaced the light bulbs and checked the fuses. All the other lights work.

Check for power with a test light with the light connected. If you have power then its the ground. If no power then you will need to trace the wire back to find break. As I recall they did have seperate fuse for left and right headlight high & low beam. Also did you get a defective new bulb?

check low beam fuse when switched on if it has voltage registering across the fuse ,if there is voltage across the low beam RHS fuse then it is possibly a pinched wire from the headlight running back towards inside of the car

check for a damaged wire for the low beam. Also wouldn't hurt to check the ground wire as the high beam will try and ground through the low beam but not visa verse

When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(

This is going to be a problem with your light switch or dimmer switch. Replace the light switch and see if that resolves the issue.

First it is possible that both low beam filaments in bulb are burnt. Check fuses for low beam before replacing the bulbs.

if the fuses are good then you need to check for power and ground at the headlight plug that attaches to the headlight bulb if you have a good power and ground there and the connections are good then the bulbs are both no good.or if you can tell the bulbs are burnt out by looking at them then you don`t have to check powers and grounds.you also can directly feed power and ground to the bulb and check both the terminals for high beam and low beam as you cannot tell which is which by looking at the terminals

Day time running lights run low voltage to the high beam bulbs so it sounds to me like you need two new bulbs or you need to check the fuses and see if any need replaceing.

Hi,
It has been because the lamp bulb or halogen lamp module has reached the end of its serviceable life, not because of any wiring problems. Low beam burns out first because it is on the most. If low beam is lost simultaneously in both headlights, I would check fuse first, then the headlight switch. If low beam is lost on one side only, it is almost always going to be due to the bulb or lamp module needing to be replaced. In that case, replace them in both headlights because the other one will be going kaput in short order, as well.
Most like the low beam filiment is bad but the high beam filiment is still good, try replacing bulb. If replacing bulb does not fix problem then you probably have voltage problems and should check the voltage reading and the plug.
OR
isolate the wire that comes from the headlight switch to the headlamp bulbs for low beam and check to see if there is a short in the wire. You can find this wire by using a test light turn on the key and get a good ground with the test light poke the wire and see if the test light illunimates with the headlight switch on.
check the wires, and check the fuse for your lowbeams. could of blown a fuse on your lows, but your highs will still work.

The fuse box is located in the engine compartment,on the driver's side. Has thumb-screw retained cover.
Thanks for contacting fixya.com

Yes your daytime running light just uses the headlight bulb on a lower voltage so if the headlight is not working the drl will not work as well, they are dirrectly related,,check the head light fuse,and check to make sure the bulb is good,,