Car been stood for 2yrs 2.2tid no fuel feed cant locate fuel pump i removed tank but unit in tank is only a sender unit cant see how fuel gets up to injection pump

Relieve the fuel pressure at the pump switch located in the passenger compartment under the carpet of the transmission hump on the passenger side. Remove the fuel tank. Turn the lock ring counterclockwise until it's loose and remove the lock ring. Pull the fuel pump/sending unit from the tank being careful not to bend the arm for the sending unit float. Discard the old lock ring seal. Installation is reverse of removal with the following additions: (a)Apply a coat of heavy grease to the new lock ring seal to hold it in place during assembly. Install the seal in the lock ring groove. (b)Install the fuel sender/pump unit into the fuel tank so that the tabs of the unit are positioned into the slots in the fuel tank. Make sure to keep the seal in place during installation until the lock ring has been tightened properly. (c)Hold the fuel sender/pump unit in place, install and tighten the locking ring clockwise until the stop is against the retainer ring tab. - Mazda Pickups Repair Manual

hope this help

Removal & Installation
Through the trunk servicing panel...

1. Before servicing the vehicle, refer to the Precautions section.
   
2. Properly relieve the fuel pressure.
   
3. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear package trim
     
   • Service hole cover
     
   • Fuel pump cover
     
   • Fuel pump connector
     
   • Fuel hoses
     
   • Fuel pump and gauge sender unit as an assembly
     
   • Fuel pump from the sender bracket
     

To install:

• New O-ring set
  
• Fuel pump to the sender bracket
  

NOTE

Pull the fuel pump down so that it is tight against the bracket.

• Fuel pump and gauge sender unit as an assembly
  
• Fuel hoses
  
• Fuel pump connector
  
• Fuel pump cover
  
• Service hole cover
  
• Rear package trim
  
• Negative battery cable
  

The fuel pump is part of the fuel sender assembly located inside the fuel tank.

1. Release the fuel system pressure and disconnect the negative battery cable.
2. Drain the fuel tank, then raise and safely support the vehicle.
3. Remove the fuel tank from the vehicle.
4. Clean the area surrounding the sender assembly to prevent contamination of the fuel system.
5. To remove the fuel sender from the tank, remove the fuel sender assembly nuts and retaining ring. Carefully remove the sending unit from the fuel tank. Discard the O-rings.
6. If necessary, separate the fuel pump from the sending unit assembly.

To install:

1. If removed, install the fuel pump to the sending unit. If the strainer was removed, it must be replaced with a new one.
2. Inspect and clean the O-ring mating surfaces.
3. Install a new O-ring in the groove around the tank opening. If applicable, install a new O-ring on the fuel sender feed tube.
4. Install the fuel sender assembly as follows:
   1. The fuel pump strainer must be in a horizontal position, and when installed, must not block the travel of the float arm. Gently fold the strainer over itself and slowly position the sending assembly in the tank so the strainer is not damaged or trapped by the sump walls.
   
   
5. Install the retaining ring and nuts, then tighten the nuts to 63 inch lbs. (7 Nm).
6. Install the fuel tank assembly.
7. Lower the vehicle.
8. Fill the fuel tank, tighten the fuel filler cap and connect the negative battery cable.
9. Turn the ignition switch to the ON position for 2 seconds, OFF for 10 seconds, then back to the ON position. Check for fuel leaks.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

GM Camaro/Firebird 1993-1998 Repair Guide Fuel Pump - REMOVAL & INSTALLATION
(see Figures 1 and 2)
The fuel pump is part of the fuel sender assembly located inside the fuel tank.

1. Release the fuel system pressure and disconnect the negative battery cable.
2. Drain the fuel tank, then raise and safely support the vehicle.
3. Remove the fuel tank from the vehicle.
4. Clean the area surrounding the sender assembly to prevent contamination of the fuel system.
5. To remove the fuel sender from the tank, remove the fuel sender assembly nuts and retaining ring. Carefully remove the sending unit from the fuel tank. Discard the O-rings.
   

Fig. 1: Exploded view of the fuel tank and sender assembly

1. If necessary, separate the fuel pump from the sending unit assembly.
   

Fig. 2: Fuel sender and pump assembly


To install:

1. If removed, install the fuel pump to the sending unit. If the strainer was removed, it must be replaced with a new one.
2. Inspect and clean the O-ring mating surfaces.
3. Install a new O-ring in the groove around the tank opening. If applicable, install a new O-ring on the fuel sender feed tube.
4. Install the fuel sender assembly as follows:
   1. The fuel pump strainer must be in a horizontal position, and when installed, must not block the travel of the float arm. Gently fold the strainer over itself and slowly position the sending assembly in the tank so the strainer is not damaged or trapped by the sump walls.
      
5. Install the retaining ring and nuts, then tighten the nuts to 63 inch lbs. (7 Nm).
6. Install the fuel tank assembly.
7. Lower the vehicle.
8. Fill the fuel tank, tighten the fuel filler cap and connect the negative battery cable.
9. Turn the ignition switch to the ON position for 2 seconds, OFF for 10 seconds, then back to the ON position. Check for fuel leaks.

Hope this help (remember rated this post). Good luck.

Camaro, Firebird, 1999 - 2002 Repair Guide
Fuel Pump - Removal & Installation

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Relieve the fuel system pressure.
3. Drain the fuel tank.
4. Clean the area surrounding the sender assembly to prevent contamination of the fuel system.
5. Remove or disconnect the following:
   Fuel tank Fuel sender-to-fuel tank retaining ring Fuel sender from the fuel tank Fuel pump from the sending unit
   
   
   Fig. Fuel sender/pump assembly component identification
   

To install:

1. Install or connect the following:
   NOTE The fuel pump strainer must be in a horizontal position and must not block the float arm travel.
   Fuel pump with new strainer onto the sending unit New O-ring in the tank opening groove New O-ring on the fuel sender feed tube
2. Fold the strainer over itself and slowly position the sending assembly in the tank so the strainer is not damaged or trapped by the sump walls.
   Retaining ring Fuel tank. Torque the bolts to 33 ft. lbs. (45 Nm). Fuel filler cap Negative battery cable
   
3. Turn the ignition switch to the ON position for 2 seconds, OFF for 10 seconds, then back to the ON position. Check for fuel leaks.

Hope this help (remember rated and comment this), good luck.

The fuel pump and sending unit is located in the tank. I hope your tank is empty, if not you will need to siphon it out. It is dangerous with the gasoline, and remember the fumes burn, not gas. You start by removing the filler hose, then loosen straps, detach sending unit wire and fuel line, then lower tank. Then unscrew the sending unit/pump and replace. reinstall.

I believe this is same truck as Ranger

Pump is in tank

Removal
NOTE: On some vehicles, fuel gauge sending unit is not available separately. On those vehicles, to replace sending unit, replace entire fuel pump .

1. Remove fuel tank as described in this section.

Removal and Installation
NOTE: Make sure fuel tank is properly supported during removal and installation procedures.

1. Drain fuel from fuel tank .

1. Loosen fill pipe clamp.

1. Remove bolts securing shield and bracket assembly to frame (5005) and remove assembly from vehicle.

1. Remove fuel tank filler pipe from vehicle.

1. Support fuel tank .

1. Remove bolts and nuts from rear fuel tank support strap and remove rear fuel tank support strap .

1. Remove bolt and nut from front fuel tank support strap and remove front fuel tank support strap .

1. Lower fuel tank .

1. Remove fuel feed hose at sender push connector.

1. Remove fuel return hose at sender unit push connector.

1. Disconnect sender and fuel pump electrical connector.

1. Remove fuel vapor hose from fuel vapor valve .

1. Lower fuel tank from vehicle

1. Remove fuel tank to bench. Remove any dirt that has accumulated around the fuel pump attaching flange so that it will not enter the fuel tank during fuel pump removal.

1. Turn the fuel tank sending unit locking retainer ring (9A307) counterclockwise with the Fuel Tank Lock Ring Wrench Tool T90T-9275-A or T86T-9275-A and remove fuel tank sending unit locking retainer ring .

1. Remove the fuel pump and sender assembly.

1. Remove fuel pump mounting gasket (9417) and discard.

1. If necessary, disconnect spade connector and remove two screws and fuel gauge sending unit.

Disconnect battery ground strap before beginning to work on the fuel/electrical system. Do not smoke or have anything in the area which can ignite or cause sparks

1. Drain enough fuel from tank to prevent spilling, no more than 4 gallons (16 liters) of fuel should remain. Use suitable pumping equipment.
2. Remove floor mat and panel from trunk.

1. Disconnect wiring harness connector to sending unit. Remove wires from connector.
2. Disconnect ground wire to sender. Push wires through grommet.
3. Remove cover for access to tank sending unit.

1. All models: Disconnect from the fuel tank sending unit:

1. Breather hose C
2. Return hose A
3. Supply hose B
4. Filler hose D
5. Wiring harness from clip E

1. Clean area and unscrew fuel tank sender/pump cap or equivalent. Remove tank sender/pump and seal.
2. Remove pump from sender/pump assembly.

INSTALLATION

1. Inspect the pump for damage, feed pump hose and wiring for wear. Replace as needed.
2. Install new pump to sender/pump assembly.
3. Install rubber seal in neck of tank. Lubricate inside of seal.

1. Install fuel tank sender/pump unit. Align it with the moulded joint (arrows) on tank.
2. Apply rustproofing compound to exposed metal portions of tank sender.

CAUTION : With tape or rubber caps, protect fuel sender openings from overspray.

1. Torque fuel tank sender/pump lock ring to: 22 ft-lb (30 Nm)
2. Reassemble components in reverse order. Use tie straps to secure all hoses and wiring.

iam from sunny spain please be more specific??do you mean you have no fuel pressure into common rail injector feed,if so check for feed to pump in the fuel tank..if you have a feed then renew the pump.the pump wires to sender unit will be bigger and thicker than the gauge sensor wires

1. Before servicing the vehicle, refer to the Precautions Section.
2. Relieve the fuel system pressure.
3. Drain the fuel tank.
4. Clean the area surrounding the sender assembly to prevent contamination of the fuel system.
5. Remove or disconnect the following:
   • Fuel tank
   • Fuel sender-to-fuel tank retaining ring
   • Fuel sender from the fuel tank
   • Fuel pump from the sending unit Fuel sender/pump assembly component identification

To install:

1. Install or connect the following: NOTEThe fuel pump strainer must be in a horizontal position and must not block the float arm travel.
   • Fuel pump with new strainer onto the sending unit
   • New O-ring in the tank opening groove
   • New O-ring on the fuel sender feed tube
2. Fold the strainer over itself and slowly position the sending assembly in the tank so the strainer is not damaged or trapped by the sump walls.
   • Retaining ring
   • Fuel tank. Torque the bolts to 33 ft. lbs. (45 Nm).
   • Fuel filler cap
   • Negative battery cable
3. Turn the ignition switch to the ON position for 2 seconds, OFF for 10 seconds, then back to the ON position. Check for fuel leaks