At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
do you mean the switch or the key tumbler. You did not have to remove the steering wheel to replace either one . Place the key in the run position ,with a small punch or screwdriver locate the hole in the bottom of the column shroud. push in and pull out the tumbler. The swicth is held on by two t30 torx screws.do you mean the switch or the key tumbler. You did not have to remove the steering wheel to replace either one . Place the key in the run position ,with a small punch or screwdriver locate the hole in the bottom of the column shroud. push in and pull out the tumbler. The swicth is held on by two t30 torx screws.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
remove the steering wheel. then remove the little round black cover. after that you at the turn signal assymbly, remove it by the 3 philips screws gently pull it out. to the right of the steering shaft youll see a screw right under the ignition assembly . put the key in the ignition rotate it to on remove the screw and pull the igintion cylinder out. put the new one in and replace the screw. some have a push pin inplace of the screw simply push it in and pull cylinder out. hope that helps you.
Try turning the steering wheel back and forth like a giggle while turning the igintion by hand.Iunderstand the wheel wont turn but it will a little each way.If this doesn't work take the lower piece of the colume of to get access to igintion.Hope this helps.
Removal & Installation
The ignition switch or warning switch can be replaced without removing the steering lock assembly. The ignition switch is on the back of the assembly and the warning switch on the side.
Disconnect the negative battery cable and insulate the terminal end.
CAUTION
The air bag system must be disarmed before removing the steering wheel. Failure to do so may cause accidental deployment, property damage or personal injury.
Remove the steering wheel and the steering column upper and lower covers.
Remove the spiral cable assembly.
View of the steering lock and ignition switch assembly
Remove the combination switch from the steering column.
Remove steering column support nuts and lower the steering column.
Disconnect the ignition switch wiring and interlock cable (if equipped).
Remove the bolts that secure the steering lock and remove steering lock assembly.
To install:
Install the steering lock assembly and secure with new shear type bolts.
Connect the ignition switch wiring harness and the interlock cable.
Raise the steering column and secure with mounting nuts.
Install the spiral cable assembly.
Install the combination switch, steering column covers, and the steering wheel.
Connect the negative battery cable and enable the air bag system.
Disconnect negative on battery. Pull steering wheel with steering wheel puller. Take off turn signal assembly.
Put key in old lock, turn to on, you will see small hole on top of steering housing, put in stiff wire to push back retainer holding old lock, pull old lock out, install new lock, reverse procedure.
Pull the horn cap off, it should have plastic tabs that lock into a metal cylinder underneath, but will pop off pretty easily. That metal cylinder should be held on by 3 screws. Under those screws is a plastic washer and your contact ring. If you're replacing a steering wheel and need to pull the old one buy, rent or borrow a steering wheel puller. There's nothing worse than having to explain to your buddies how you broke your nose removing a steering wheel. They puller looks like a crows foot. It has three slots on one side and one on the back side. You can use three bolts to attach it to the steering wheel. I wrench will work to screw down the large bolt in the center and the steering wheel will come right off. Put a new steering wheel on, new contacts, and you should be set to go.
ok first thing first take steering wheel off its kinda hard to do anyway take steering wheel off u might loosen the nut on the steering half way off and put your knees on back of steering wheel then hit nut with hammer as u pull up with your knees or buy a wheel puller cost around 20.00 but id rather just use hamer and my knees after u get wheel off they will be a lock wheel its black in the center is a meatal o ring clip u have to push down realy hard on that round lock and take o ring out after u get it out pull the black ring lock off then the plastic horn thing out then u will see the turn sng switch they are three screws in it taake them out dont take wires loose leave them just pull it out let it hang down thenu will look down see on back of lock mist have a screw there lossen it then take switch out slide the new one in then fun part putting all back together
You will need some tools like a steering wheel puller and a few other tools. Take the cover off the steering wheel and the centre nut from the steering wheel. Use the remover to pull the steering wheel. Take the shroud off of the column and you will be able to see what is holding the switch onto the column. Remove the wiring harness and remove screws for the turn signal switch. There might be a star with a pin in the centre. Put the new switch on and put it all back together.
do you mean the switch or the key tumbler. You did not have to remove the steering wheel to replace either one . Place the key in the run position ,with a small punch or screwdriver locate the hole in the bottom of the column shroud. push in and pull out the tumbler. The swicth is held on by two t30 torx screws.
Do you replacing ignition switch or key lock cylinder
×