1998 grand cherokee limited failed etest trouble code p1764 governor pressure sensor voltage to low how do i fix

Definition of Diagnostic Trouble Code P1041 Saab: Injector Cylinder 4 Shorting To Ground

There is no definition for DTC P1047

CodeDescription P1192 Inlet Air Temp. Circuit Low P1193 Inlet Air Temp. Circuit High P1195 1/1 O2 Sensor Slow During Catalyst Monitor P1196 2/1 O2 Sensor Slow During Catalyst Monitor P1197 1/2 O2 Sensor Slow During Catalyst Monitor P1198 Radiator Temperature Sensor Volts Too High P1199 Radiator Temperature Sensor Volts Too Low P1281 Engine Is Cold Too Long P1282 Fuel Pump Relay Control Circuit P1283 Idle Select Signal Invalid P1284 Fuel Injection Pump Battery Voltage Out Of Range P1285 Fuel Injection Pump Controller Always On P1286 Accelerator Pedal Position Sensor Supply Voltage Too High P1287 Fuel Injection Pump Controller Supply Voltage Low P1288 Intake Manifold Short Runner Solenoid Circuit P1289 Manifold Tune Valve Solenoid Circuit P1290 CNG Fuel Pressure Too High P1291 No Temp Rise Seen From Fuel Heaters P1292 CNG Pressure Sensor Voltage Too High P1293 CNG Pressure Sensor Voltage Too Low P1294 Target Idle Not Reached P1295 No 5 Volts To TP Sensor P1296 No 5 Volts To MAP Sensor P1297 No Change in MAP From Start To Run P1298 Lean Operation At wide Open Throttle P1299 Vacuum Leak Found (IAC Fully Seated) P1388 Auto Shutdown (ASD) Relay Control Circuit P1389 No Auto Shutdown (ASD) Relay Output Voltage At PCM P1390 Timing Belt Skipped One Tooth or More P1391 Intermittent Loss of CMP or CKP P1398 Mis-Fire Adapter Numerator at Limit P1399 Wait To Start Lamp Circuit P1403 No 5 Volts To EGR Sensor P1475 Aux. 5 Volt Output Too High P1476 Too Little Secondary Air P1477 Too Much Secondary Air P1478 Battery Temp Sensor Volts Out of Limit P1479 Transmission Fan Relay Circuit P1480 PCV Solenoid Valve P1482 Catalyst Temperature Sensor Circuit Shorted Low P1483 Catalyst Temperature Sensor Circuit Shorted High P1484 Catalytic Converter Overheat Detected P1485 Air Injection Solenoid Circuit P1486 Evap Leak Monitor Pinched Hose P1487 Hi Speed Rad Fan CTRL Relay Circuit P1488 Auxiliary 5 Volt Supply Output Too Low P1489 High Speed Fan CTRL Relay Circuit P1490 Low Speed Fan CTRL Relay Circuit P1491 Rad Fan Control Relay Circuit P1492 Battery Temperature Sensor Voltage Too High P1493 Battery Temperature Sensor Voltage Too Low P1494 Leak Detection Pump Switch or Mechanical Fault P1495 Leak Detection Pump Solenoid Circuit P1496 5 Volt Supply Output Too Low P1498 High speed Rad Fan Ground CTRL Rly Circuit P1594 Charging System Voltage Too High P1595 Speed Control Solenoid Circuits P1596 Speed Control Switch Always High P1597 Speed Control Switch Always Low P1598 A/C Pressure Sensor Volts Too High P1599 A/C Pressure Sensor Volts Too Low P1602 PCM Not Programmed P1680 Clutch Released Switch Circuit P1681 No I/P Cluster CCD/J1850 Messages Received P1682 Charging System Voltage Too Low P1683 Speed Control Power Relay Or Speed Control 12 Volt Driver Circuit P1684 Battery Disconnected Within Last 50 Starts P1685 Skim Invalid Key P1686 No SKIM Bus Message Received P1687 No Cluster Bus Message P1688 Internal Fuel Injection Pump Controller Failure P1689 No Communication Between ECM & Injection Pump Module P1690 Fuel injection pump CKP Sensor Does Not Agree With ECM CKP Sensor P1691 Fuel Injection Pump Controller Calibration Failure P1693 DTC Detected In ECM Or PCM P1694 No CCD Messages Received From ECM P1695 No CCD/J185O Message From BCM P1696 PCM Failure EEPROM Write Denied P1697 PCM Failure SRI Mile Not Stored P1698 No CCD Messages Received From PCM P1719 Skip Shift Solenoid Circuit P1740 TCC Or OD Solenoid Performance P1756 Governor Pressure Not Equal To Target At 15?20 PSI P1757 Governor Pressure Above 3 PSI When Request Is 0 PSI P1762 Governor Pressure Sensor Offset Improper Voltage P1763 Governor Pressure Sensor Voltage Too High P1764 Governor Pressure Sensor Voltage Too Low P1765 Trans 12 Volt Supply Relay Control Circuit P1899 Park/Neutral Position Switch Stuck In Park or In Gear

Read more at: http://www.obd-codes.com/trouble_codes/dodge/
Copyright © OBD-Codes.com

CODE P1763 - GOVERNOR PRESSURE SENSOR SIGNAL HIGH.POSSIBLE CAUSES SIGNAL WIRE SHORT CIRCUIT TO POSITIVE,VOLTAGE SUPPLY WIREOPEN CIRCUIT,TRANSMISSION FLUID LEVEL LOW,GOVERNOR PRESSURE SENSOR FAILED OR PCM AND TCM HAS FAILED.

P1757 - Governor Pressure Above 3 PSI When Request Is 0 PSI

P1762 - Governor Pressure Sensor Offset Improper Voltage

Both codes are refered at the governor pressure sensor; I am 99% certain that is bad. Just replace it. Check the voltage on the Light Green/White wire at pin 29 in the white PCM connector with key ON, engine OFF (KOEO). It should be about 0.5-0.7 volts.

If higher than 0.8 volts, check the Transmission Temperature sensor reading on a scan tool. If the Transmission Temperature sensor reads normal, the sensor ground is OK. If the sensor ground is OK, then replace the Governor Pressure sensor.

Hope this helps.

Trouble code P1762 means: Governor pressure sensor offset improper voltage. Gov. Pressure Sensor.It is located in the valve body of the transmission and requires dropping the transmission pan to replace. Sounds much more difficult than it is. Since you have to change your fluid it's a good idea to change the trans. filter .

P1762 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Sensor Offset Volts Too High/Low Conditions: Key on or engine running. Gear selector in Park or Neutral. PCM detected an out-of-range Governor Pressure Sensor signal for 1.3 seconds. The fault must occur 3 times on one trip to set a code. Possible Causes: Governor pressure Sensor VREF (5v) circuit is open Governor pressure Sensor ground circuit is open P/N switch is damaged or has failed (not operating properly) Transmission fluid has excessive debris or it is contaminated PCM has failed

CHRYSLER OBDII DTC

P1101 HCM/PCM Communication Performance

P1103 Turbocharger Waste Gate Actuator Malfunction

P1104 Turbocharger Waste Gate Solenoid Malfunction

P1105 Fuel Pressure Solenoid Malfunction

P1195 Slow Switching O2 Sensor Bank One Sensor One During catalyst monitoring

P1196 Slow Switching O2 Sensor Bank two Sensor one During catalyst monitoring

P1197 Slow Switching O2 Sensor Bank One Sensor two During catalyst monitoring

P1198 Radiator Temperature Sensor Input voltage too high

P1199 Radiator Temperature Sensor Input voltage too low

P1281 Engine is cold too long

P1282 Fuel Pump Relay control circuit

P1283 Idle select signal invalid

P1284 Fuel Injection pump battery voltage sensor out of range

P1285 Fuel Injection pump controller always on

P1286 Accelerator Position Sensor (APPS) supply voltage too high

P1287 Fuel Injection pump Controller Supply voltage low

P1288 Intake manifold short runner tuning valve solenoid circuit

P1289 Manifold tune valve solenoid circuit

P1290 CNG Fuel system pressure too high

P1291 No Temp rise seen from intake heaters

P1292 CNG Pressure sensor voltage too high

P1293 CNG Pressure sensor voltage too low

P1294 Target idle not reached

P1295 No 5 volts to TP sensor

P1296 No 5 volts to MAP sensor

P1297 No change in MAP sensor from start to run

P1298 lean operation at wide open throttle

P1299 Vacuum Leak detected (IAC fully seated)

P1300 Ignition timing adjustment circuit failure

P1388 Auto shutdown relay control circuit

P1389 No ASD relay output voltage at PCM

P1390 Timing belt skipped one tooth or more

P1391 Intermittent loss of CMP or CKP

P1398 Mis-Fire Adaptive Numerator at Limit (PCM is unable to learn the crank sensors signal

for use in preparation for misfire diagnostics

P1399 Wait to start lamp circuit

P1403 No 5 volt feed to EGR

P1475 Auxiliary 5 volt supply is too high

P1476 Too little secondary air

P1477 Too much secondary air

P1478 Battery Temp Sensor Volts out of limit

P1479 Transmission Fan Relay Circuit

P1480 PCV Solenoid Circuit

P1481 EATX (Electronic Automatic Transaxle) RPM pulse generator performance

P1482 Catalyst Temperature Sensor Circuit shorted low

P1483 Catalyst Temperature Sensor Circuit shorted high

P1484 Catalytic Converter overheat detected

P1485 Air injection solenoid circuit

P1486 EVAP Leak Monitor found a pinched hose

P1487 Hi Speed Fan #2 Circuit

P1488 Auxiliary 5 volt supply output is too low

P1489 High speed fan control relay circuit

P1490 Low speed fan control relay circuit

P1491 Radiator fan relay control circuit

P1492 Ambient/ Battery Temp sensor input voltage too high

P1493 Ambient/ Battery Temp sensor input voltage too low

P1494 Leak detection pump pressure switch or mechanical fault

P1495 Leak detection pump solenoid circuit

P1496 5 volt supply, output too low

P1498 High speed radiator fan ground control relay circuit

P1500 General alternator 'FR' Terminal circuit fault

P1594 Charging system voltage too high

P1595 Speed control solenoid circuits

P1596 Speed control switch always high

P1597 Speed control switch always low

P1598 A/C pressure sensor input voltage too high

P1599 A/C pressure sensor input voltage too low

P1680 Clutch released switch circuit

P1681 No I/P Cluster CCD/ J1850 messages received

P1682 Charging system voltage too low

P1683 Speed control servo power control circuit

P1684 The battery has been disconnected within the last 50 starts

P1685 The SKIM (Smart Key Immobilizer Module) has received an invalid key

P1686 No SKIM (Smart Key Immobilizer Module) bus message received

P1687 No Mechanical Instrument cluster bus message

P1688 Internal Fuel injection pump controller failure

P1689 No communication between the ECM and injection pump module

P1690 Fuel injection pump CKP sensor does not agree with the ECM CKP sensor

P1691 Fuel injection pump controller calibration error

P1692 Fault in companion Engine control module

P1693 A companion DTC was set in both the ECM and PCM

P1694 No CCD message from PCM- Aisin transmission

P1695 No CCD message from body control module

P1696 PCM failure EEPROM write denied

P1697 PCM Failure SRI (Service Reminder Indicator) mileage not stored

P1698 No CCD message from TCM

P1719 Skip shift solenoid circuit

P1740 TCC solenoid or overdrive solenoid performance

P1756 Governor pressure not equal to target at 15-20 psi

P1757 Governor pressure is above 3 PSI when 0 PSI is requested

P1762 Governor pressure sensor offset improper voltage

P1763 Governor pressure sensor voltage to high

P1764 Governor pressure sensor voltage to low
P1765 Transmission 12 volt supply relay control circuit

see response to
http://www.fixya.com/cars/t4242851-governor_pressure_sensor
to get you started

1762 has to do with too high or too low voltage from the governor pressure solenoid valve in the transmission.
To test this code accurately, you would need to have Chrysler connect their scan tool to it. With that, they can check the whole system.
The governor pressure sensor measures output pressure of the governor pressure solenoid valve. It is located in the governor body on the valve body transfer plate.
It is not very difficult to replace,

P1757 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Above 3 PSI In Gear At 0 MPH Conditions: Engine started; vehicle driven to a speed over 30 mph, and the PCM detected the Governor Pressure Sensor was more than 3 psi with the requested pressure at 0 psi (95% duty cycle command) for 2.65 seconds. The fault must occur twice on one trip to set the code. Possible Causes: Check for the presence of other A/T related trouble codes Governor pressure Sensor is damaged or has failed Governor pressure Sensor VREF (5v) circuit is open or shorted Transmission valve body is leaking, damaged or has failed PCM has failed P1762 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Sensor Offset Volts Too High/Low Conditions: Key on or engine running. Gear selector in Park or Neutral. PCM detected an out-of-range Governor Pressure Sensor signal for 1.3 seconds. The fault must occur 3 times on one trip to set a code. Possible Causes: Governor pressure Sensor VREF (5v) circuit is open Governor pressure Sensor ground circuit is open P/N switch is damaged or has failed (not operating properly) Transmission fluid has excessive debris or it is contaminated PCM has failed