Question about 2005 Jeep Grand Cherokee

2 Answers

Need to replace heating core

Have to replace the heating core in my 2005 Jeep Grand Cherokee Limited Edition 5.7L Hemi engine

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

Why not just read the FSM (factory service manual)
in the HVAC chapter,.
click WK here
then its special, the whole manual in pdf downloads
then click HVAC.

http://www.morris4x4center.com/knowledge-base/index.htm?utm_source=cj#service

best deal on a jeep like this there is, and 100% free and real.
real OEM book, clean.

posted over 300 times.

Posted on Dec 13, 2016

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 105 Answers

  1. Disconnect and remove the negative battery.
    CAUTION After disconnecting the negative battery cable, wait 2 minutes for the driver-s/passenger-s air bag system capacitor to discharge before attempting to do any work around the steering column or instrument.
  2. Drain the cooling system into a clean container for reuse.
  3. Remove the instrument panel by performing the following procedure:
    1. Turn the steering wheel in the straight-ahead position.
    2. Remove the knee blocker from the instrument panel.
    3. Remove the steering column; do not remove the air bag module, the steering wheel or switches from the steering column.
    4. From under the driver-s side of the instrument panel, disconnect the following items:

      Instrument panel wiring harness connector from the 100-way wiring harness connector at the left side of the inner panel. Side window demister hose at the heater/air conditioning housing demister/defroster duct on the driver-s side.
    5. Remove the glove box.
    6. Reaching through the glove box opening, disconnect the following items:

      Two halves of the heater/air conditioning system vacuum harness connector. Instrument panel wiring harness connector from the heater/air conditioning system wiring harness connector. Instrument panel wiring harness connector from the passenger-s side air bag module wiring harness connector. Side window demister hose at the heater/air conditioning housing demister/defroster duct (passenger-s side). Two halves of the radio antenna coaxial cable connector. Two instrument panel wiring harness connectors from the passenger air bag ON/OFF switch wiring harness connector. Passenger-s side air bag ON/OFF switch wiring harness from the retainer clip on the plenum bracket that supports the heater/air conditioning housing just inboard of the fuse block module. Two lower passenger-s side air bag module bracket-to-dash panel nuts.
    7. Remove the upper cover from the instrument panel.
    8. Remove the 3 instrument panel-to-door hinge pillar screws.
    9. Remove the 4 upper instrument panel-to-dash nuts.
    10. Using an assistant, remove the instrument panel from the vehicle.

  4. If equipped with air conditioning, discharge and recover the air conditioning system refrigerant.
  5. Disconnect the refrigerant lines from the evaporator. Plug the refrigerant openings to prevent evaporation.
  6. Disconnect the heater hoses from the heater core tubes.
  7. Disconnect the heater/air conditioning system vacuum supply line connector from the T-fitting near the heater core tubes.
  8. In the engine compartment, remove the 5 heater/air conditioning housing-to-chassis nuts. If necessary, loosen the battery hold-downs and reposition the battery for access.
  9. Remove the cowl plenum drain tube from the heater/air conditioning housing stud; it-s located behind the cylinder head on the cowl.
  10. From the bottom of the heater/air conditioning housing, remove the floor duct.
  11. On the passenger side, remove the heater/air conditioning housing-to-plenum bracket screw.
  12. Pull the heater/air conditioning housing down far enough to clear the defrost/demist and fresh air ducts, then, rearward far enough to clear the mounting studs and the evaporator drain tube to clear the dash panel holes.
  13. Remove the heater/air conditioning housing assembly from the vehicle.
  14. Remove the heater/air conditioning housing upper case.
  15. Lift the heater core from the lower half of the heater/air conditioning housing.need to replace heating core - a35714c.gif
9414058.gif

need to replace heating core - a01902f.gifttp://i.fixya.net/uploads/images/a01902f.gif" alt="a01902f.gif" class="h_mi" />

Posted on Feb 13, 2010

  • shaddow4115
    shaddow4115 Feb 13, 2010

    To install:




    1. Assemble the heater core into the lower half of the heater/air conditioning housing.


    2. Install the heater/air conditioning housing upper case.


    3. Install the heater/air conditioning housing assembly to the vehicle.


    4. On the passenger-s side, install the heater/air conditioning housing-to-plenum bracket screw.


    5. At the bottom of the heater/air conditioning housing, install the floor duct.


    6. Install the cowl plenum drain tube to the heater/air conditioning
      housing stud; it-s located behind the cylinder head on the cowl.



    7. In the engine compartment, install the 5 heater/air conditioning housing-to-chassis nuts.


    8. Connect the heater/air conditioning system vacuum supply line connector to the T-fitting near the heater core tubes.


    9. Connect the heater hoses to the heater core tubes.


    10. Connect the refrigerant lines to the evaporator.


    11. If equipped with air conditioning, evacuate and charge the air conditioning system refrigerant.


    12. Install the instrument panel by performing the following procedure:



      1. Using an assistant, install the instrument panel to the vehicle.


      2. Install the 4 upper instrument panel-to-dash nuts.


      3. Install the 3 instrument panel-to-door hinge pillar screws.


      4. Install the upper cover to the instrument panel.


      5. Reaching through the glove box opening, connect the following items.






        Two lower passenger-s side air bag module bracket-to-dash panel nuts.


        Passenger-s side air bag ON/OFF switch wiring harness to the
        retainer clip on the plenum bracket that supports the heater/air
        conditioning housing just inboard of the fuse block module.



        Two instrument panel wiring harness connectors to the passenger air bag ON/OFF switch wiring harness connector.


        Two halves of the radio antenna coaxial cable connector.


        Side window demister hose at the heater/air conditioning housing demister/defroster duct (passenger-s side).


        Instrument panel wiring harness connector to the passenger-s side air bag module wiring harness connector.


        Instrument panel wiring harness connector to the heater/air conditioning system wiring harness connector.


        Two halves of the heater/air conditioning system vacuum harness connector.






      6. Install the glove box.


      7. Under the driver-s side of the instrument panel, connect the following items:






        Side window demister hose at the heater/air conditioning housing demister/defroster duct on the driver-s side.


        Instrument panel wiring harness connector to the 100-way wiring harness connector at the left side of the inner panel.






      8. Install the steering column.


      9. Install the knee blocker to the instrument panel.






    13. Connect and remove the negative battery.


    14. Refill the cooling system.


    15. Run the engine to normal operating temperatures; then, check the climate control operation and check for leaks.
    If you need more help feel free to contact me


×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Jeep Grand Cherokee Limited 5.7 Hemi Check engine light on, code P0750


2008 jeep cherokee (hemi) engine light its on i brought to fix they change 4 sensor and the converter. After 5 days engine light comes on again, what else can be? im depress about it, after paying almost 2 grand to fix this issue.

Jan 25, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

05 grand cherokee limited 5.7 hemi quadra drive 2. will not go into any gear


Frozen ice around shift mechanism. Oil in trans is too thick. Try adding a heat lamp or blanket around the transmission area.

Dec 06, 2013 | 2005 Jeep Grand Cherokee

1 Answer

How do i replace/install a heater core for a 1999 limited edition jeep cherokee 4.0 liter 6cyclinder


I would make sure the core is the problem. You may have a heater control valve that cuts off flow to the core by vac. or a blend door that cuts off air flow thru the core.
You will need a shop manual to replace the core. The dash and console have to come out, along with discharging the ac.

Dec 18, 2012 | 1999 Jeep Grand Cherokee

1 Answer

2005 jeep garnd cherokee rocky mountain edition is just blowing cold air.I will not heat up untill you drive the vehicle. Any suggestions?


If the temeperature gauge says the engine is warm but the air is not warm until you drive it would most likely it would be the heater core partially clogged. Have it flushed.


Please take a moment to rate my answer .........Thanks

Dec 01, 2010 | 2005 Jeep Grand Cherokee

1 Answer

05 grand cherokee with hemi won;t start.


Does it turn over? If not, try disconnecting the battery and reconnecting it. This has worked for my Jeep before.

Jul 06, 2009 | 2005 Jeep Grand Cherokee

2 Answers

2005 Jeep Grand Cherokee (HEMI) Service Electric Brake System


Problem is a faulty Steering Angle Sensor (part of Steering Module) located in steering column ...replacement part $600.00.

Apr 14, 2009 | 2005 Jeep Grand Cherokee

1 Answer

2005 jeep grand cherokee limited 5.7 hemi vehicles hesitates


The egr valve is located on the front of the right cylinder head. It has a tube attached to it and going to the intake manifold.It has failed and is why your jeep is running rough and hesitating. Replace it and it will fix your driveabllity issues. Disconnect the battery for 2 min to clear the code.

Apr 01, 2009 | 2005 Jeep Grand Cherokee

1 Answer

1999 Grand Jeep Cherokee (limited) shuts off while driving


Starter...if the starter is old, it is getting heat soaked. Replace the solenoid.

Mar 17, 2009 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2005 Jeep Grand Cherokee Logo

798 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

83940 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22441 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...