Question about 1999 GMC Sierra

1 Answer

I think that it is overstearing. It feels like your in 4 wheel drive when turning sharp, but the truck is not in 4 wheel drive (jacked up one side at a time, tires spin freely, also mech. shop checked that). When you watch the truck turn the tires look like it is being pushed not rolling. The problem started when I replaced upper and lower balljoints, tierod ends inner and outer, iddler arm and pitman arm. To replace the pitman arm I had to unbolt steering box to fit my puller. The truck has a 4 in. lift with 275/65/R16 tires. I tell you this because I took it to the GMC dealer in Anchorage, AK and they told me that the tires were too small for my lifted truck, but the truck had those same tires on it before I did the front end and it did not have this problem. So I put on some 31X12.5R16 and it still turned rough. The truck has been aligned and then double checked and drives straight down the road. Can't notice problem on highway only turning sharp in parkinglots. Is there something that stops the steering from going too far? I can't find anything in my Chilton.

Posted by on

  • norris_j Feb 09, 2010

    I have not bought one yet but it sounds like a good idea thanks

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 6,927 Answers

If it has a steering damper on it,it maybe the wrong one,if it does not,install one,this will allow it to only steer so far,and that is it,it also stabilizes the steering,some call it a steering stabilizer.

Posted on Feb 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bad sway bar


Could be CV Shaft or Hub Bearing as well. Jack up the front of the car, support with Jack Stands and check for play in wheels/hubs/bearings/linkage by grabbing wheel at 3 and 9 o'clock positions for tie rod ends and steering linkage, then 12 and 6 o'clock positions for bearings. You should barely be able to feel play. If you think it is more than acceptable climb under the car while someone else performs the tasks above. Turn wheels for excessive brake noise or out of tolerance discs. Out of tolerance discs will cause premature brake wear and cause pads to move around in the caliper sometimes before starting to grind. Finally, and what I think you're hearing/feeling is the CV Shaft. Grab shaft, move around feeling for excessive play in joint or splines on each end. Turn steering all the way lock to lock and turn wheels at each lock, forward and backward, feel/listen for clicking/popping. Most of the time you can quickly easily diagnose bad CV Joints in a parking lot by slowly, safely driving in a circle forwards and backwards making the joint noise more pronounced. If it is a CV Joint, my advice would be to spend the extra few bucks and replace the whole shaft while you're there. Its quicker and easier requiring less specialty tools to complete the job.

Dec 26, 2013 | 2005 Pontiac Grand Prix

1 Answer

All three lights are blinking on the 4 wheel drive selector on my Chevy S10 4 wheel drive pickup


you will know if you are in 4wd if you take it on a dry road. you will feel it fighting you when you turn sharp.. as for the blinking lights . that's your truck saying..........please take me in for some servise

Dec 02, 2013 | 1991 Chevrolet S-10 Blazer

1 Answer

I have a 03 Jeep Liberty - whether I'm pulling in or out of a parking spaced and turning the wheels, it feels as if something is grabbing or rubbing against the front wheels. Making u-turns is extremely...


it is difficult to make sharp turns while in 4 wheel drive on a hard surface. If you are able to make sharp turn easily in 2 wheel drive then everything is probably OK. Check your owners manual and review the 4 wheel drive section, there is much to learn.

Oct 20, 2010 | Jeep Liberty Cars & Trucks

2 Answers

My 2001 cavalier makes aconstant humming noise. When I turn to the right it goes away. I am thinking it is the wheel bearing in the front right. Has anybody else noticed something similar?


Correct diagnosis, but make sure it isn't the left bearing. Jack the car up and check both wheels for play. If no play, start and put in drive (while still jacked up off both wheels), and listen to each side for the noise.

Sep 02, 2010 | 2001 Chevrolet Cavalier

1 Answer

Feels like my front drivers side tire is lose but I check all the lugg nuts and they are tight. I can drive straight and I get a loud sqweal(as if I'm taking a corner to sharp) from the passenger side...


sounds like you have either tie/thrust rod ends going bad, or ball joints. Your wheel bearings could be going bad as well. Any of these can cause this problem. To check the tie/thrust rod ends, turn the vehicle off, and have a friend turn the wheel back and forth while you look at the steering linkages. If you see anything moving more than the part that it's attached to, you have found something that needs replacing right away. For Ball joints, put a jack on the a-arm right beside the wheel. Jack it up, and watch the tire as it starts to come off the ground. If it slides out when it just gets off the ground, you have bad ball joints on that side. Wheel/hub bearings can be trickier, unless they're REALLY worn. Jack the car up so that it's clear of the ground, and see if you can make the wheel wobble by moving it with your hands. You may also notice a grinding or whining sound coming from the affected side. You'll especially notice it if you drive with your window down, as you're passing a building or other hard object, as the sound reflects back at you. Hope this helped you find your problem.

May 11, 2010 | Cars & Trucks

2 Answers

I think that it is overstearing. It feels like your in 4 wheel drive when turning sharp, but the truck is not in 4 wheel drive (jacked up one side at a time, tires spin freely, also mech. shop checked...


The tirerods on the burbans can get wedged when turning sharp. Have seen a couple do it.

Just to double-check, you can Check for your stearing trim is in the middle and not pushed aside. Once you have done that, take everything apart, gears out and etc... turn on the car. Let the servo center and pop everything in as carefully as you can and close as the middle as you can. Re-assemble and see if it's any better.

Also, check your servo wires leading onto the board. See if any of them are loose or have even fallen off.

Another possibility that I have seen is when you turn the wheel all the way to the lock, the power steering pump is still trying to turn it further, which is why the steering feels jerky. You can blow up the pump, or a hose, by holding the wheel against the lock. You won't turn any wider if you let the wheel come back one quarter turn, but you will take the pressure off of the pump.

Feb 08, 2010 | 1999 GMC Suburban

2 Answers

My 2003 mountaineer when I drive in reverse and turn will come to a stop if I don't really push on the gas. I have had the wheel bearings changed and the rear clutch fluid drained - that did not work -...


it sounds like your 4 wheel drive is engaged. whether on purpose or its stuck thats your problem, to double check jack up one of your front tires, if it wont turn then thats your problem

Nov 05, 2009 | 2003 Mercury Mountaineer

3 Answers

SYMPTOMS OF BALL JOINT WEAR


If you make a hard right or left hand turn (with steering wheel turned until it stops) you'll hear and feel a pop sensation.When you drive over potholes you'll feel a slight pull to one side.If it is one of the upper balljoints,you can grab the tire with both hands near the top(11 and 1 o'clock) and pull the wheel back and forth.You will feel looseness if the upper balljoint is bad.

Nov 01, 2009 | 2002 Ford Taurus

Not finding what you are looking for?
1999 GMC Sierra Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...