Question about 2001 Porsche Boxster

1 Answer

Do you have to pull the enginin to replace head gaskets?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 52 Answers

Yes, its impossible to remove heads with engine in situ

Posted on Apr 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 04 xl7 overheated I pulled all 6 spark plugs and coolant present in all cylinders.is it the heads or gasket? Will turn over but want start


it wont start with that much coolant the plugs foul up immediately as to if gasket or head that many cylinders with fluid u will have to pull head and have it inspected gasket replacement is a gimmie but head possible warped or cracked

May 24, 2016 | Cars & Trucks

2 Answers

How to stop water from bubbling in the expansion bottle after changing head gasket water pump heat sender unit


why did you need to change the head gasket in the first place ?
There may be a reason the gasket failed like a crack in the head or a warp in the head of the engine.

May 09, 2016 | Cars & Trucks

1 Answer

Head gasket or lower intake gasket on 98 Blazer


this does sound like a head problem (hopefully just the gasket). pulling the head with the exhaust manifold attached is possible but tricky and difficult. risking the bolt and drilling it out if it snaps would be alot easier. I would strongly suggest having the head checked while its off (so you dont rebuild to find that you wasted time and money on a bad head)

Feb 11, 2014 | Cars & Trucks

1 Answer

I have a 1985 cj7 and I replaced my turn signal switch and t everything back together but now the emergency lights stay on and the switch formthem only turns I believe its suppose to pull out to turn on...


I just put 4 new p[lugs in the car and the enginine lite is flickering and its loosing power they tested it and said the oxygen sensor is bad where is it located 2002 ford escort se

Dec 17, 2013 | Jeep CJ7 Cars & Trucks

1 Answer

How to replace a head gasket on a Buick Park Avenue 1992 with a 3800 engine


Are you sure its a head gasket? The coolant cross over gaskets on the intake manifold are famous for blowing out and simulating a head gasket failure. 9 out of 10 times this is the problem. Good part is you have to pull the intake to do a head gasket, so id pull off the intake first, its not that hard on this motor. If they are blown you wont have any problem telling it.

Oct 27, 2013 | Cars & Trucks

1 Answer

My car is honda 2000 civic si dohc vtec. Has about 45k on it. The motor was replaced with my old one. Anyway when we replaced the motor. It was blowing white smoke at reving rpm. Its not black or blue but...


either blown head gasket or cracked head, coolant only escapes into motor in two ways, before you replace head gasket again, pull head, have it magnafluxed ( To Show Cracks) if there arenonehave the head resurfaced

Sep 27, 2012 | Cars & Trucks

1 Answer

Water in oil


Water in the oil is most likely a head gasket leak-blown head gasket. You will have to pull the cylinder head off and replace the head gasket. If it's a V6 or V8 engine, a compression test will tell you which bank of the engine has the head gasket problem. One cylinder or two cylinders next to each other will have low compression.

May 23, 2012 | 1985 Chevrolet Chevy

1 Answer

Oil coming from head gasket left side of piston # 1 I replaced head gasket and it steal leaks in the same spot. why wouldn't a new head gasket fix this problem? 1994 metro geo


You replaced the gasket, did you have the head checked? It might have a bow or warp in it. Might need to be shaved. This IS something you do when you pull the head. You will need to pull it again( yes, replace the gasket again) and have it checked. This will probably be the problem. 9 times out of 10, that's it( been doing this too many years). Pay and have it checked. hope this helps, and sorry to make you spend money like this

Jan 19, 2011 | 1994 Geo Metro

2 Answers

Oil in overflow of radiator.


If you have coolant mixed in you oil you have blown a head gasket at the very least. You will have to pull the heads and replace the gasket.

Jun 21, 2009 | 1996 Honda Civic

Not finding what you are looking for?
2001 Porsche Boxster Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...