Question about 1997 GMC Jimmy

2 Answers

I have 96 chevy silverado extended cab with a vibrationfrom the differential. I found a 2000 gmc Envoy rear end 5 lug. will this bolt up?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 167 Answers

Pzcapp is right, and also the Envoy is a narrower rear axle (mid-size SUV) than a Silverado (full-size PU), and is built for a lower-torque/gross vehicle weight truck. Check the U-joints first (front drive shaft too if it is a 4WD), then worry about having the drive shaft(s) checked/trued/balanced. Drive shafts are balanced at the factory with welded-on weights which sometimes (rarely) fall off.

Posted on Feb 15, 2010

Most vibrations are driveshaft being bent,worn u-joint,in need of balance,shocks,wheels,tires and more.I will bet ,swapping the complete rear axle will not change a thing. If it is lifted, you should know your in for problems. If not, and all else fails,strip the rear housing and go through it. The one you swap, may be more worn than yours and not even a good core to rebuild.

Posted on Feb 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How To Install Differential Cover Fluid Chevy Trailblazer GMC Envoy 02-09...


<a href="http://www.1aauto.com">How To Install Replace Rear Differential Cover Fluid Chevy Trailblazer GMC Envoy 02-09 1AAuto.com</a><br /><br /><utube src="NktjOhKMhJ8"><br />

on Jun 09, 2011 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

Where is the tail light fuse?


The tail light fuse is under the rear seat on the drivers side.

Jan 17, 2016 | 2003 GMC Envoy

1 Answer

Rear end axle removal for a 2000 chevy truck 1500


You must remove the rear cover on the differential and then the spider gears, then the center pin bolt and the pin then push in on the axle and remove C clip retainer inside the gear carrier and slide axle out.

Mar 27, 2013 | 2000 Chevrolet Silverado 1500

1 Answer

How do I remove the rear axle


The rear axle shaft?? Or the entire axle? I'm going to go with the axle shaft. Secure the vehicle. Loosen the lug nuts. Jack it up. Take the wheel and tire off. Remove the caliper and/or bracket. Remove the rotor. Place a pan under the rear differential cover. Remove the rear differential cover. Spin the axle shaft to reveal the center pin. Locate the 8mm-5/16 bolt that holds the center pin in place. Remove that bolt. Slide the center pin out, BUT DON'T TURN THE AXLE SHAFTS WHILE ITS OUT! Push the axle shaft in from the outer portion (where the wheel goes). A "C" clip will fall out inside of the differential. Pull the axle shaft out. Slide the center pin back in. Replace the 8mm-5/16 locking bolt and spin it a few times to keep everything in place.

Feb 23, 2011 | 2000 GMC Jimmy

1 Answer

How do you get the front driveshaft out of 2001 chevy 4X4


Remove transfer case shield. Remove clamp on boot
where front drive shaft meets transfer case. use a flat
screwdriver to pry free end up and release clamp. (you need a special clamp tool to reinstall clamp )
Remove 4 bolts at differential end that hold U joint Retainers to yoke. Slide drive shaft to rear enough to clear yoke. then let drive shaft drop so it clears differential and slide forward until it come off transfer case shaft.

Sep 12, 2010 | 2000 Chevrolet Silverado

Not finding what you are looking for?
1997 GMC Jimmy Logo

257 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...