Question about 1995 Chevrolet Blazer

1 Answer

How do i remove and reinstall the turn signal switch assembly

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

Give these websites a try www.alldatadiy.com and www.autozone.com you can also stop by your local GM dealership in the parts department and they be able to print you off the pictures and diagrams you will need if all fails stop by your local library and get your hands on a Haynes auto repair manual for your truck wish you the best of luck Michigan Man.

Posted on Feb 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the turn signal switch?


Remove steering wheel cowls.Unscrew and remove switch stalk assembly. Disconnect wiring.
Refit new assembly in reverse

Nov 14, 2012 | 2006 Ford Taurus

1 Answer

How to change multifunction switch on 04 buick century


STEP BY STEP INSTRUCTION First, any time you work around the steeringcolumn you it is a must to disable the air bag system you will do this my disconnectingthe battery. After you disconnect the battery wait at least 5 minutes before proceeding. 1. Ifyou have tilt remove the tilt actuator arm by firmly pulling straight out. 2. Removethe upper and lower trim covers. 3. Removethe wire harness assembly from the wire harness strap. 4. Disconnect the turn signal andmultifunction switch assembly connector from the SIR system coil connector.This is alongside the steering column there is an 8mm bolt in the center of theconnector that must be removed to disconnect the connector halves. 5. Slide the 2 connectors of the turnsignal and multifunction switch assembly out of the bulkhead connector. With a smallscrewdriver slightly pry between the connectors to release them. 6. Removethe 2 pan head tapping screws and from the turn signal and multifunction switchassembly. 7. Removethe turn signal and multifunction switch assembly from the steering column tilthead assembly. INSTALLATION PROCEDURE 1. Installthe turn signal and multifunction switch assembly onto the steering column tilthead assembly. 2. Screwthe 2 pan head tapping screws and into the turn signal and multifunctionassembly.3. Slidethe 2 connectors of the turn signal and multifunction switch assembly into thebulkhead connector. 4. Connectthe turn signal and multifunction switch assembly connector to the SIR coilconnector. 5. Installthe wire harness assembly (1) into the wire harness strap (2). 6. Installthe upper and lower trim covers. 7. Installtilt actuator arm. 8. Reconnectthe battery.


Mar 01, 2011 | Buick Century Cars & Trucks

1 Answer

How to replace head light


The headlight replacement procedure.:---
  • Apply the parking brake and open the hood.The head is attached by thumb shaped screw.You will see the thumb screw on the upper inboard corner of the turn signal assembly Remove the screw with the screwdriver.Pull the turn signal assembly outward away from the fender and then disconnect the bulb.Turning the socket and wire 1/4- counterclockwise. Set the turn signal assembly aside.Disconnect the electrical connector plug from the headlight being replaced. Lift up on the blue retaining clip of the plug and pull it away from the socket of the headlight.Turn the black retaining collar of the headlight counterclockwise to remove it and the headlight from the headlight assembly.Install the new headlight by reversing the procedure.Replace the turn signal bulb into its assembly and reinstall the assembly and thumbscrew.

    Thanks.Helpmech.



  • Nov 12, 2010 | 2005 Pontiac Montana SV6

    2 Answers

    How to replace the turn signal switch in a 1992 Cadilac?


    Turn Signal Switch REMOVAL & INSTALLATION CAUTION
    Some models covered by this manual may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column, and instrument panel disable the SRS. Deville, Eldorado, Seville, and Fleetwood - Early Models
    1. Disable the SIR system.
      1. On Deville and Fleetwood, remove the left lower sound insulator. On Eldorado and Seville, remove the left side sound insulator.
      2. Remove the Connector Position Assurance (CPA) and detach the yellow 2-way connector at the base of the steering column.
      3. Remove the steering wheel.
      4. Make sure the ignition switch is in the LOCK position to prevent the SIR coil assembly from going off-center.
    2. Remove the SIR coil assembly retaining ring and the coil assembly. Allow the coil to hang freely. WARNING
      The SIR coil assembly will become off-center if the steering column is separated from the steering gear and is allowed to rotate or if the centering spring is pushed down, letting the hub rotate while the coil is removed from the column.
    3. Remove the wave washer.
    4. Use tool J-23653-C or equivalents, to depress the shaft lock, then remove and discard the shaft lock retaining ring.
    5. Remove the shaft lock.
    6. Remove the turn signal canceling cam assembly.
    7. Remove the upper bearing spring, upper bearing inner race seat and inner race.
    8. Move the turn signal switch to the RIGHT TURN position.
    9. On Deville, Fleetwood, and 1990 Eldorado, and Seville, remove the multi-function turn signal lever as follows:
      1. Make sure the lever is in the OFF position.
      2. Remove the access cover from the steering column housing.
      3. Detach the cruise control wiring connector. Note the position of the connector when installed in the column.
      4. Pull the lever straight out of the turn signal switch.
    10. On Eldorado and Seville, remove the multi-function turn signal lever as follows:
      1. On 1992-93 vehicles, slide the connector cover toward the front of the vehicle.
      2. Unplug the electrical connector. On 1991 vehicles, note the position of the connector when installed in the column.
      3. Push the lever straight in, rotate clockwise 1?4 turn and pull the lever out of the switch.
    11. On Deville, Fleetwood, and Eldorado and Seville, remove the screw, button, spring, and hazard warning switch knob.
    12. On Deville and Fleetwood, remove the one signal switch arm retaining screw. On Eldorado and Seville, remove the 2 signal switch arm retaining screws. Remove the signal switch arm.
    13. Remove the turn signal switch retaining screws.
    14. Remove the wiring protector and detach the turn signal switch connector.
    15. Gently pull the wire harness through the column and remove the turn signal switch. prev.gif next.gif

    Nov 12, 2010 | 1992 Cadillac DeVille

    1 Answer

    How to replace the ignition on a 1991 oldsmobile cutlass cierra


    If you mean the ignition lock cylinder:

    Ignition Lock Cylinder CAUTION
    If the car is equipped with an air bag, do not service the steering column or dashboard components. Extreme danger of air bag deployment exists even with the battery removed! Serious injury could occur. REMOVAL & INSTALLATION Without Air Bag
    1. Place the ignition switch in the RUN position.
    2. Remove the lockplate, turn signal switch and buzzer switch.
    3. Remove the screw and lock cylinder. NOTE: If the screw is dropped on removal, it could fall into the column, requiring complete disassembly to retrieve the screw. To install:
    4. Rotate the cylinder clockwise to align cylinder key with the keyway in the housing.
    5. Push the lock all the way in.
    6. Install the screw. Tighten the screw to 14 inch lbs. (2 Nm) for adjustable columns and 25 inch lbs. (3 Nm) for standard columns.
    With Air Bag CAUTION
    Before proceeding, refer to Section 6 for information on disabling and enabling the SIR (air bag) system; otherwise, serious injury could occur.
    1. Turn the steering wheel so the vehicles wheels are pointed straight ahead.
    2. Place the ignition switch into the LOCK position to prevent undercentering of the coil assembly.
    3. Disable the SIR system. Disconnect the negative battery cable.
    4. Remove the coil assembly retaining ring, then disconnect the inflatable restraint coil assembly. Let the switch hang freely if removal is not needed. To remove the coil assembly proceed.
    5. Remove the wave washer, then the shaft retaining lock ring with tool J-23653-SIR to push down on the shaft lock. Dispose of the ring, it is not reusable. Fig. 1: Special tool J-23653-SIR or equivalent is required for pushing down the shaft lock to remove the shaft ring 86818085.gif
    6. Remove the shaft lock, then disconnect the canceling cam assembly.
    7. Remove the upper bearing spring, race seat and race.
    8. Position the turn signal to the right turn (up) position.
    9. Remove the multi-function lever and hazard knob assembly. Unfasten the round washer head screw and signal switch arm, along with the turn signal switch screws.
    10. Remove the turn signal switch assembly by unfastening the connector from the bulkhead connector. Gently pull on the harness through the column and disconnect.
    11. Make sure the coil assembly does not become uncentered, this could happen if the centering spring is pushed down letting the hub rotate while the coil is removed from the steering column.
    12. Remove the inflatable restraint coil assembly with the wiring harness from the column assembly.
    13. Remove the wire protector, then attach a length of mechanics wire to the coil terminal connector to aid in reassembly. Then gently pull the wire through the column.
    14. Remove the key from the steering column lock cylinder set, then remove the buzzer switch assembly.
    15. Reinsert the key into the lock cylinder, turn it to the LOCK position.
    16. Remove the lock retaining screw, then the cylinder. To install: NOTE: Make sure all fasteners are securely seated before applying the necessary torque. If you fail to do so, component damage or malfunctioning of the steering column may occur.
    17. Install the lock cylinder assembly, insert the retaining screw, then tighten to 22 inch lbs. (2.5 Nm).
    18. Insert the key into the lock cylinder. Install the buzzer switch assembly. Turn the key to the LOCK position.
    19. Install the turn signal switch assembly wiring harness through the column, let the switch hang freely. Connect the wiring to the bulkhead.
    20. Insert the coil assembly wiring harness through the column letting the coil hang freely. Attach the turn signal assembly with the binding head screws. Tighten the screws to 30 inch lbs. (3 Nm).
    21. Attach the signal switch arm with the round washer head screw, tighten the screw to 20 inch lbs. (2 Nm).
    22. Install the hazard knob assembly and the multi-function lever.
    23. Install the inner race, upper bearing race seat and spring. Attach the turn signal cancelling cam assembly, apply grease for lubrication.
    24. Replace the shaft lock and install a new shaft lock retaining ring. Use tool J-23653–SIR or equivalent to push down on the shaft lock. The ring must be firmly seated in the groove on the shaft. NOTE: Set the steering shaft so that the block tooth on the race and upper shaft is at the 12 o'clock position. The wheel on the car should be straight ahead. Set the ignition switch to the LOCK position, as this will ensure no damage to the coil assembly.
    25. Install the wave washer, then attach the coil assembly, make sure it is centered correctly. Fig. 2: Centering the coil assembly is important in assembling the column assembly 86818086.gif

    26. Attach the coil assembly retaining ring, the ring must be firmly seated in the groove on the shaft.
    27. Gently pull the lower coil assembly, turn signal, and pivot (pulse) wires to remove any kinks that may be inside the steering column assembly. If you fail to do this you can damage the wiring.
    28. Complete assembling the steering column assembly.
    29. Attach the negative battery cable.
    30. Check the functions of the turn signal, make sure it cancels when turned on and the steering wheel is turned.
    31. Enable the SIR system. prev.gif next.gif

    Aug 01, 2010 | 1991 Oldsmobile Cutlass Ciera

    1 Answer

    How to replace the ignition switch


    1. If equipped with an air bag, disable the system as outlined in of this repair guide.
    2. If not done already, disconnect the negative battery cable.
    3. Remove the steering wheel, as outlined earlier in this section.
    4. Remove the shaft lock cover.
    5. Remove the shaft lock retaining ring using a suitable lock plate compressor tool to press down the shaft lock. Dispose of the ring.
    6. Remove the shaft lock.
    7. Remove the turn signal canceling cam assembly.
    8. Remove the upper bearing spring.
    9. Remove the thrust washer.
    10. Move the turn signal lever up, into the "right turn" position.
    11. Remove the multi-function lever.
    12. Remove the turn signal switch arm retaining screw.
    13. Remove the turn signal switch screws and let the switch hang freely.
    14. Remove the key from the lock cylinder set.
    15. Remove the buzzer switch assembly.
    16. Reinsert the key in the lock cylinder.
    17. Turn the key to the LOCK position.
    18. Remove the lock retaining screw and remove the lock cylinder.
    19. If equipped with cruise control, remove the housing cover end cap, unplug the cruise control connector and gently pull through the shroud, bowl, and steering column housing assembly.
    20. Remove the washer head screw, the hex nut and dimmer switch.
    21. Remove the mounting stud and ignition switch.
      1. If equipped with cruise control, gently pull the connector through the steering column housing assembly, bowl and shroud and connect the plug.
      2. Install the housing cover end cap and screw and tighten to 17 inch lbs. (1.9 Nm).
      3. Install the ignition switch and mounting stud and tighten the stud to 35 inch lbs. (4.0 Nm). Adjust the ignition switch by moving the switch slider to the extreme left position and then move the slider 1 detent to the right (off lock).

      See Figure 1


      0900c152801dbcc2.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Ignition switch adjustment procedure
      1. Install the dimmer switch hex nut, screw, and tighten to 35 inch lbs. (4.0 Nm). Adjust the dimmer switch.
      2. To adjust the dimmer switch, depress the switch slightly to allow insertion of a 3 / 32 in. drill bit into the hole above the actuator rod. Force the switch upward then tighten the screw.

      See Figure 2


      0900c152801dbcc3.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Dimmer switch adjustment procedure
    22. Install the switch using the original screws. Use of screws that are too long could prevent the column from collapsing on impact.
    23. Install the lock cylinder and retaining screws and tighten to 40 inch lbs. (4.5 Nm).
    24. Turn the key to the RUN position.
    25. Install the buzzer switch assembly.
    26. Install the turn signal switch and retaining screws and tighten to 31 inch lbs. (3.5 Nm).
    27. Install the wire protector shield.
    28. Install the turn signal switch arm and retaining screw and tighten to 29 inch lbs. (2.3 Nm).
    29. Install the hazard knob assembly.
    30. Install the multi-function lever.
    31. Install the thrust washer and upper bearing spring.
    32. Lubricate with synthetic grease and install the turn signal canceling cam assembly.
    33. Install the shaft lock.
    34. Install a new shaft lock retaining ring. Align it to the block tooth on the shaft, using a lock plate compressor tool to press down the shaft lock.
    35. Install the shaft lock cover.
    36. Install the steering wheel, as outlined earlier in this section.
    37. Connect the negative battery cable. If equipped, enable the air bag system as outlined in of this repair guide.

    Jan 19, 2010 | 1993 Oldsmobile Silhouette

    1 Answer

    I need to install my cruise control switch on my steering wheel . How do I go about removing the back cover on the steering wheel?


    Removal & Installataion
    1. Verify that the multifunction turn signal lever is in the center of the OFF position.
    2. Disconnect the negative battery cable.
    3. Disable the SIR (air bag) system. Refer to the Chassis Electrical Section.
    4. Remove the air bag module from the steering wheel.
    5. Remove the steering wheel.
    ca4e20e.gif
    Exploded view of the shroud-type steering column showing shrouds, wiring and multifunction switch that includes the headlamp function

    1. Remove the upper and lower steering wheel trim covers using the following procedure.
    2. Remove the tilt lever assembly.
    • Remove the two pan head tapping screws from the lower shroud.
    • Unlock the upper and lower shroud.
    • Remove the two Torx® head screws from the upper shroud.
    • Remove the upper shroud.
    1. Remove the wire harness straps from the wire harness assembly and detach the wiring harness connectors from the switch side connectors.
    2. Remove the two multifunction turn signal switch screws and remove the multifunction switch assembly from the vehicle.
    To install:
    1. Install the multifunction switch to the steering column. Use a small flat-blade prytool to compress the electrical contact and move the multifunction turn signal switch into position. Verify that the electrical contact rests on the canceling cam. Install the screws and tighten to 62 inch lbs. (7 Nm).
    2. Route the wire harness along the steering column jacket assembly and secure into the wire harness strap. Install a new wire tie to the upper tilt head assembly and another lower along the wiring harness, as the original installation.
    3. Verify that the lever is in the center of the OFF position.
    4. Install the upper and lower steering column shrouds.
    5. Route the SIR connector through the steering wheel, align the scribe mark on the steering wheel made at removal, with the slash mark on the steering shaft and install the steering wheel. Install the steering shaft nut and torque to 30 ft. lbs. (41 Nm).
    6. Install the horn contact leads and the air bag connector to the back of the air bag. Make sure the CPA wedge is in place to secure the connector. Install the air bag by gently pushing on both the right and left sides of the air bag until the retaining springs engage.
    7. Enable the SIR system by connecting the yellow 2-way connector at the base of the steering column and installing the air bag fuse.
    8. Connect the negative battery cable. Test the horn, turn signals and headlight operation.
    1. Disable the SIR system.
    2. Remove the upper and lower trim covers.
    3. Remove the knee bolster.
      NOTE The abrasion sleeve located on the steering column wire harness assembly must be reinstalled. Make note of what connector is coming out of the abrasion sleeve for installation purposes.

    4. Remove the wire harness assembly from the wire harness strap.
    5. Disconnect the turn signal and multifunction switch assembly connector from the SIR system coil connector.
    6. Slide the 2 connectors of the turn signal and multifunction switch assembly out of the bulkhead connector.
    7. Remove the 2 pan head tapping screws and from the turn signal and multifunction switch assembly.
    8. Remove the turn signal and multifunction switch assembly from the steering column tilt head assembly.
    To install:
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    CAUTION Be sure that the electrical contact of the turn signal and multifunction switch assembly (2) rests on the turn signal cancel cam assembly.

    CAUTION The abrasion sleeve must be installed back onto the steering column wire harness assembly. The ignition lock cylinder case wires and connector must be hanging out of the middle of the abrasion sleeve.

    1. To install, reverse removal procedure.
    2. Tighten the following to specification.
      • Top pan head tapping screw: 27 inch lbs. (3 Nm).
      • Side pan head tapping screw: 62 inch lbs. (7 Nm).
    CAUTION When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling . Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.

    Dec 08, 2009 | 2005 Chevrolet Impala

    1 Answer

    How do i change right turn lamp in my 2004 pontiac grand prix


    Answer remove the headlight assembly and the bulbs are located below the Assembly to remove headlamp assembly and access signals: -open the hood
    -while pushing rearward on the headlamp,pull up half-way on the (white)plastic retaining clip on the electrical connector - align the square cut-out on the retaining clip with the notch on the headlamp
    -pull the headlamp assembly straight out from the vehicle (moving the headlamp up and down slightly may help with its removal)
    -locate the front turn signal,parking lamp and foglamp bulbs which are located below the headlamp assembly (turn/parking lamp on top and the fog lamp is below it)
    -turn the bulb socket 1/4 turn counterclockwise to remove it from assembly
    -pull the old bulb from the socket and replace it with a new one
    -turn the bulb socket a 1/4 turn clockwise to reinstall it
    -reinstall the headlamp assembly carefully so you dont scratch the paint
    -push down on (white)plastic retaining clip on the electrical connector while pushing rearward on the headlamp making sure headlamp is secure.

    Nov 26, 2009 | 2004 Pontiac Grand Prix

    2 Answers

    Having problems with my turn signals, they do not work when i just click the turn signal, I have to hold them in a specific way for them to come on.


    step by step heres what you got to do
    1.disconnect battery ground cable
    2.remove nut retainer and jam nuts hten steering wheel
    3.remove turn signal cancel cam assembly
    4.remove hazard warning screw and knob
    5.move the turn signal switchso you can access the turn signal screws and housing screws which can be accessed through the opening in the switch
    6.remove housing screws and housing
    7.only on models with tilt steering wheels remove shoe pin retainer cap
    8.remove pivot switch screw and pivot pluse switch assembly
    9.remove turn signal screws
    10.remove wire prtecting from opening in instrument panel bracket assemblyand seperate from wires
    11.disconnect turn signal switch connector from ignition and dimmer switch assembly connector
    12.disconnect 17 wy lock from turn signal connector
    13.use ternimnal tool #j-35689-a or equivelent, disconnect wires on buzzer switch assemble from turn signal connector
    14.remove turn signal switch assembly from column
    15 reverse to put back together
    16. please note that signal and column housing screws got to be torqued to 35 inch lbs the switch screws at 20 inch lbs hazards at 7 inch lbsand the jam nuts at 30 ft lbs

    Nov 21, 2009 | 1992 Pontiac Grand Prix

    2 Answers

    Turn signal switch is dead. Not working at all. Not sure where its located to replace the switch


    hi how are you? the turn signal switch is behind your steering wheel in the column.must remove horn assembly.then steering wheel,use puller to remove wheel.next remove clip that holds steel plate.(tool required).remove plate.then remove any steering column covers/plastic.then remove screws for turn signal switch.unplug wires and remove.then reinstall in reverse.

    Feb 02, 2009 | 1993 Mercury Cougar

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    21 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76649 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8522 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...