Question about 2002 Ford F150 Regular Cab

1 Answer

2002 f-150 code P1151 , P1131 idle lowers and comes back up when cold, dealer said lower intake manifold gasket. sounds like they are honest.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

P1151 states lean condition at bank 2

Posted on Mar 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rough idle Oldsmobile alert 02 only in drive


Check the codes. If it's the 3.4 vs then a good chance either a lower intake manifold gasket leaking or blown head gaskets as that is very common on that engine and is more noticeable in gear. Honestly hard to answer with specifics without more details including any codes stored.

Jan 04, 2017 | 2002 Oldsmobile Alero

1 Answer

P1131 and p1151 codes in 2001 mercury grand marquis, how do i fix it?


Try cleaning the MAF sensor first, then check for any unmetered air getting into throttle body (leaks in intake hose). Bank 1 is the driver's side of the engine (or front on FWD) and bank 2 is the passenger side.

Mar 02, 2015 | 2001 Mercury Grand Marquis

2 Answers

I have a 2001 Ford Escape XLT wait a V6 3.0L engine. This last week it has not wanted to idle, it will stall out coming to a stop light. I went to the parts store and got the error codes, but could...


Just did this for a friend ,before you spend any money do the upper and lower intake gasket this vehicle is notorious for this..won't be cheap but i had same problem change one part another code would pop up.this gasket job will set u back about 300-$500 dollars depending where u take it..parts are about $80 it's the labor.good luck

Nov 03, 2013 | Ford Taurus Cars & Trucks

1 Answer

Code 1150 on a 1997 ford f 150 with a 4.2 motor


I will try to paste an article for you. Several sources indicate this is a Bank 2 O2 sensor problem and that it is failing to switch and adjust for the fuel mix. But as you can see, many defects can lead up to this O2 sensor Code 1150.

I would try to use a spray bottle of water and go around the Intake manifold and spray the water while the engine is running. An intake leak will draw water into the engine and change RPM.

If no success then try changing the O2 bank 2 sensor. You may need to wipe the computer and clear the Code. H40 DTCs P1131, P1132, P1151 AND P1152: UPSTREAM HO2S NOT SWITCHING. DTC P1130: FUEL SYSTEMicon1.png NOT SWITCHING AT FUELicon1.png TRIM (RICH OR LEAN)
Diagnostic Trouble Codes (DTCs) P1131 bank 1 (Cylinder 1) and P1151 bank 2 indicate the fuel/air ratio is correcting rich for an overly lean condition. The HO2S voltage is less than 0.45 volt. DTCs P1132 bank 1 (Cylinder 1) and P1152 bank 2 indicate the fuel/air ratio is correcting lean for an overly rich condition. The HO2S voltage is greater than 0.45 volt.
DTC P1130 and P1150 indicate the fuel control system has reached maximum compensation for a lean or rich condition and the HO2S is not switching.
DTC/HO2S Reference List
•HO2S-11 = DTCs P1131, P1132 and P1130
•HO2S-21 = DTCs P1151, P1152 and P1150
Possible causes:
Fuel system
•Excessive fuel pressure.
•Leaking fuel injector(s).
•Leaking fuel pressure regulator.
•Low fuel pressure or running out of fuel.
•Contaminated fuel injector(s)
•Vapor recovery system
Induction system
•Air leaks after the MAF.
•Vacuum leaks (vacuum lines and gaskets).
•Restricted air inlet.
•PCV system.
•Improperly seated engineicon1.png oil dipstick.
EGR System
•Leaking gasket.
•Stuck open EGR valve.
•Leaking diaphragm.
Base engine
•Oil overfill.
•Cam timing.
•Cylinder compression.
•Exhaust leaks before or near the HO2Ss.
•Check intake air system for leaks, obstructions and damage.
•Check air cleaner element, air cleaner housing for blockage.
•Verify integrity of the PCV system.
•Check for vacuum leaks. user_online.gif quote.gif post_old.gif )

Mar 28, 2013 | 2003 Ford Ranger Regular Cab

1 Answer

Replacing upper intake gasket 2003 E150 4.2l


Remove the 12 bolts that hold the intake to the lower section and disconnect all the hoses and linkages. Replace the lower gaskets and torque the manifold in a radiating sequence in this order.
stages to tighten
stage 1 - 59 inch pounds
stage 2 - 66 inch pounds
stage 3 - 90 degrees

Sep 17, 2012 | 2003 Ford E150

1 Answer

2001 ford windstar codes read P0171,P0174, P1131, P1151 and P1401. Need help in knowing what they mean and how to fit. Please can anyone help before it is hauled to junkyard.


Hi, the first 4 codes indicate a lean condition and the 1401 is an EGR solenoid circuit issue. If the EGR valve is stuck open, that could account for all of these codes. Typically though, the first 4 are caused by leaky intake manifold gaskets on this engine. They can also be caused by a leak in the air intake hose or resonator. Check the intake hose/resonator from the air filter to the throttle body for tears or leaks. If none, get some carb cleaning, start the engine, and spray the carb cleaner on both the upper and lower intake manifold gaskets. If the engine revs at all, you have a gasket leak.
For the EGR solenoid, I would pull the vacuum lines off and see if you can blow thru the solenoid. If yes, it's stuck open and needs to be replaced. If not stuck open, test it by applying 12 volts to pin 1 (red wire) and ground to pin 2 (brown wire). It should click open and allow you to blow thru. If not, replace the EGR valve. I would test the EGR solenoid first. As I said before, if it's stuck open, it could cause all of the codes you have. Please let me know if you have any questions and thanks for using FixYa.

EGR solenoid:

jturcotte_190.jpg


jturcotte_914.gif

Jan 26, 2011 | Ford Windstar Cars & Trucks

2 Answers

Need to replace the intake manifold


3.8L Engine (most common) Upper Intake Manifold To Remove:
  1. Drain the cooling system.
  2. Remove or disconnect the following:
    • Negative battery cable.
    • Fuel injector sight shield.
    • Air cleaner intake duct.
    • Right spark plug wires from the ignition control module and reposition.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Fuel rail assembly.
    • Brake booster hose from the vacuum source manifold in the upper intake manifold.
    • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
    • Throttle body support bracket upper bolt.
  5. Disconnect the electrical connectors from the following:
    • EVAP purge solenoid
    • Throttle Position (T/P) sensor
    • Idle Air Control (IAC) valve
    • Manifold Absolute Pressure (MAP) sensor
    • Mass Air Flow (MAF) sensor
    • EVAP purge solenoid vacuum line from the throttle body.
    • Accelerator and the cruise control cables with the bracket from the throttle body.
  6. Remove or disconnect the following:
    • Upper intake manifold bolts and stud.
    • Clean the upper intake manifold bolt threads.
  7. Remove or disconnect the following:
    • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
    • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
  8. If the upper intake manifold is being replaced, remove the following:
    • Throttle body assembly.
    • Manifold Absolute Pressure (MAP) sensor.
    • Positive Crankcase Ventilation (PCV) valve.
    • Vacuum source manifold.
Upper intake manifold bolt torque sequence (3.8L engine) gm-03-38-530.gif

To Install:
  1. If the manifold was replaced, install or connect the following:
    • Vacuum source manifold.
    • Positive Crankcase Ventilation (PCV) valve.
    • Manifold Absolute Pressure (MAP) sensor.
    • Throttle body assembly.
    • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
  2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
  3. Install or connect the following:
    • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
    • Accelerator and the cruise control cables with the bracket to the throttle body.
    • EVAP purge solenoid vacuum line to the throttle body.
  4. Connect the electrical connectors to the following:
    • Mass Air Flow (MAF) sensor
    • Manifold Absolute Pressure (MAP) sensor
    • Idle Air Control (IAC) valve
    • Throttle Position (T/P) sensor
    • EVAP purge solenoid
  5. Install or connect the following:
    • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
    • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
    • Brake booster hose to the vacuum source manifold.
    • Fuel rail assembly.
    • Right spark plug wires.
    • Air cleaner intake duct.
    • Fuel injector sight shield.
  6. Connect the negative battery cable.
  7. Fill the cooling system.
  8. Inspect for fluid or vacuum leaks.
Lower Intake Manifold (W/O Supercharger) To Remove:
  1. Remove or disconnect the following:
    • Upper intake manifold.
    • Generator brace.
    • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
    • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
    • Radiator inlet hose from the water outlet housing.
    • ECT sensor electrical connector.
    • Right upper engine mount strut bracket.
    • Generator brace bracket bolts.
    • Generator brace bracket.
    • Lower intake manifold bolts.
    • Lower intake manifold.
    • Lower intake manifold seals.
    • Lower intake manifold gaskets.
  2. If replacing the lower intake manifold, Remove or disconnect:
    • Water outlet housing bolt and stud
    • Water outlet housing
    • Gasket and the thermostat.
    • ECT sensor.
  3. Inspect the flatness of inlet flanges.
  4. Clean the intake manifold mating surfaces.
  5. Clean the intake manifold bolts and bolt holes of adhesive compound.
To Install:
  1. If removed, install the ECT sensor.
    • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
  2. If removed, install the thermostat, the gasket, and the water outlet housing.
  3. If removed, install the water outlet housing bolt and the stud.
    • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
  4. Install or connect the following:
    • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
    • Lower intake manifold seals.
    • Lower intake manifold.
    • Lower intake manifold bolts.
    NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
  5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm) gmpc_v6_5.gif

  6. Install or connect the following:
    • Generator brace bracket.
    • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
    • Right upper engine mount strut bracket.
    • ECT sensor electrical connector.
    • Radiator inlet hose to the water outlet housing.
    • EGR outlet pipe to the lower intake manifold.
    • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
    • Drive belt tensioner.
    • Generator brace.
    • Upper intake manifold.
  7. Inspect for leaks.
Lower Intake Manifold (W/ Supercharger) To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the supercharger.
  4. Remove the thermostat housing.
  5. Remove the EGR pipe at the intake manifold.
  6. Disconnect the electrical connection at the temperature sensor.
  7. Remove the intake manifold and gaskets.
NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
To Install:
  1. Clean the gasket sealing surfaces.
  2. Install the intake manifold gaskets.
  3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
  4. Install the electrical connector to the temperature sensor.
  5. Install the EGR pipe to the intake manifold.
  6. Install the thermostat housing.
  7. Install the supercharger.
  8. Fill the cooling system.
  9. Connect the negative battery cable.

Aug 05, 2010 | 1997 Pontiac Grand Prix

1 Answer

Idling rough in cold weather codes that come up are p1131 and p1151 need to know what these codes are and what parts they are


DTC P1131 DTC P1151 indicates the system is correcting RICH for an overly LEAN condition. The Heated Oxygen Sensor (HO2S) voltage is less than 0.45 volts. This is usually due to a vacuum leak after the MAF. It can also be caused by a bad PCV valve or PCV system hose. It can also be caused by low fuel pressure or a plugged injector.

Start with the simple and clean the MAF and the IAT sensor. In simple terms, the engine is running lean and is being compensated by the ECM. P1131 is bank 1 and P1151 is bank2

Good luck and keep me posted.




Feb 17, 2010 | 2001 Ford F150 Styleside SuperCrew

2 Answers

How do i fix emission codes p1131 p1151 p0171


TSB
05-22-6
ISSUE:
Some 2001-2003 F-150, 2004 F-150 Heritage and 2001-2003 E-150/250 vehicles equipped with a 4.2L engine may exhibit the malfunction indicator lamp (MIL) on with diagnostic trouble codes (DTCs) P1131 and/or P1151 (system too lean bank 1 or 2). This condition may be due to leaking isolator bolts/port gaskets in the upper-to-lower intake manifold mounting area. This condition is sometimes intermittent and may not be apparent on a warmed-up engine.


SERVICE PROCEDURE

Perform a self test. If DTC P1131 and/or P1151 are the only codes stored in the powertrain control module (PCM) proceed to Step 2. If any additional DTCs are present, follow normal diagnostic procedures found in the PC/ED Manual.

Remove the upper intake and replace only the port gaskets (9H486) and isolator bolt assemblies (9S479). The new isolator bolt assemblies use a rubber material that is green in color, do not install the old isolator bolt assemblies with the black rubber material. Do not replace any other intake parts or gaskets.
While the upper intake manifold is removed, check the exhaust gas recirculation (EGR) orifices that are pressed into each primary port of the lower intake manifold. If any of the orifices are plugged with soot, clean and unplug them with a pick and solvent.

PART NUMBER PART NAME
1L3Z-9H486-AA Port Gasket
3F2Z-9S479-AA Isolator Bolt

Jan 13, 2010 | 2003 Ford F150 Regular Cab

4 Answers

My '01 Tribute V6 3.0 has a rough idle at a cold start up, once the engine is warmed up and I have been driving for 5-10 minutes it clears up, but until then it will go dead if I do not give it gas at...


Don't waste your time. Have the intake manifold gaskets (upper and lower) replaced. Check all vacuum lines for leaks. Clamp all vacuum hose connections.
Do NOT replace any sensors unless the computer codes indicate.
THIS WILL FIX YOUR PROBLEM!

Oct 09, 2009 | 2001 Mazda Tribute

Not finding what you are looking for?
2002 Ford F150 Regular Cab Logo

Related Topics:

1,264 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...