Question about 2000 Hyundai Sonata

1 Answer

How to replace the radio in a 2000

Ok i need to get into the back of the radio in order to replace a cord for the stereo how do i get gain access into the back of the radio

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Remove the panel over the gear shift,then the screws,disconnect the lighter,.Now remove the panel covering the radio.disconnect the wires in back and there u have it.

Posted on Feb 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Want to remove double din stereo in honda stream rn6 2007 rsz?


Don't know if this will help. but the radio is often clicked into place and needs a special tool to remove it from the dash.
See If there are two holes either side of the radio just above and below the tuning button and on the other side above and below the volume button.
If so, make a special tool using a wire coat hanger. Cut two lengths of about 30 cm (12 inches) long and bend them over double. Push the two ends of each into the holes in the radio until you feel the release pins lift, then gently pull the radio out.
Maybe it doesn't work for your radio, just hoping> . . .

Oct 06, 2014 | Cars & Trucks

1 Answer

Factory stereo not working and needs replaced. how does dash come apart to do this


REMOVAL

  1. Disconnect and isolate the battery negative cable.
  2. Remove cup holder.
  3. Remove trim panel above cupholder by pulling straight out.
  4. Remove center instrument panel trim panel.
  5. Remove screws holding radio to instrument panel.
  6. Pull radio rearward to gain access to the back of radio (RADIO). CAUTION: Pulling the antenna cable straight out of the radio without pulling on the locking antenna connector could damage the cable or radio.
  7. Disconnect the antenna cable by pulling the locking antenna connector away from the radio (ANTENNA TO RADIO).
  8. Disconnect bolt holding ground strap to the radio (if equipped).
  9. Disconnect the wire connectors from the back of the radio.

Nov 19, 2013 | 2002 Dodge Grand Caravan

1 Answer

I want code for my radio for my car volvo s40 2000


The only way to access this code is through your dealer, the stereo may have to be removed if the dealer cannot access the code using the vin (vehicle identification number) they will have to access the serial number located on the back of the stereo unit to get the code from Volvo. If you have the manual for the car look through it sometimes people write the stereo code on the inside cover.

Sep 19, 2012 | 2000 Volvo S40

1 Answer

Having problems with removing old original stereo from my 93 chevy silverado, it comes in two parts and i want to replace it to a newer version. any suggestions?


the brains of radio are under dash looks just like a computer. the the display and if you had it a tape playerin the middle. need to replace them together as are matched units. remove instrument bezel rto gain access

Aug 15, 2011 | 1993 Chevrolet K1500

1 Answer

On my 2002 Santa Fe, while playing the radio the speakers keep going on and off; but the cd player is fine. How would I gain access to replace the stereo?


to access the stereo you need to remove the dash piece around the control panel. after that you will see 2 or 4 screws holding in the stereo housing remove that and the stereo should slide right out. good luck.

Feb 06, 2011 | 2002 Hyundai Santa Fe

1 Answer

I need to reconnect the radio to the antenna how do you get access to the back of the radio to plug in the antenna?


To gain access to the antena plug on 98 and later models the intrument cluster bezel has to be removed and the radio mounting screws removed in order to get to the connectors for the radio and antena connectors.TO remove the bezel you want to first remove the negative cable so that you dont accedentully set off the airbag system.Then you want to put the steering wheel in the lowest position and remove the screws in the bezel.Then with a flat screwdriver carefully pry the bezel the bezel out of the clips.Once this is done you will have access to the radio mounting screws.I hope this helps .

Feb 03, 2011 | 2003 Kia Spectra

1 Answer

Acura 2000 radio unlock code


You have to do this: If you have jumped or replaced the battery at anytime this will happen. You have to get the serial number off the radio by removing it or partially taking it out to see the numbers on it try not to remove any cords. With the stereo out (to make sure you get the right number off of it) call an Acura dealership with the number and they will give you the another number to enter into the stereo and directions on how to punch the numbers in. Make sure while you have the stereo out you write the serial number down and keep it in a safe place also the number that the Acura dealership gives you because if you sell the car or if it happens again its easily accessible. Good Luck!

Aug 19, 2010 | 2000 Acura Integra

1 Answer

How do you remove the radio out of a honda civic


good day Sir, In order to gain access to the rear of the stereo for either connection to, or replacement of the factory unit, you must first remove the panel surrounding the (manual) gear stick. This should not be attempted with any form of 'level' to avoid damage to the dash finish. To remove the surround simply press fingers into the gear gaiter to gain purchase behind the panel and firmly 'pull' the panel toward you to disengage from the clips that hold it in place. The main panel above requires removal which involves location and loosening (not necessarily removal) of two hex headed screws approximately 6 inches (150mm) down from the head unit behind the panel, which screw the vertical metal plates holding the panel to the under dash mountings. To gain access to the screws push the two stops on the glove box inwards to allow the glove box to swing downwards. On the other side remove the small panel under the steering column Once loosened, the entire stereo/ heater control panel may be pulled toward you to disengage the clips that hold it in position. Reassembly is the reverse of removal, ensuring that the screw slots are properly engaged before final tightening of screws and reinstallation of gear stick surround.i hope this will help you

Jul 07, 2010 | 2002 Honda Civic

1 Answer

How would i take my fectory radio out of the car?


Radio & Tape Player

  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the floor console and the front console panel. On 1984-85 cars, if access to the back of the radio may be gained through other means, such as removing the "pocket" from the console, the console need not be removed.

54d84d0.gif
Radio mounting on 1990-93 Accords

4. Remove the ashtray and ashtray holder.
5. Remove the two screws holding the radio at the rear of the unit.
6. Carefully push the unit out the front of the dash. When access
is gained, disconnect the multi-pin connector and
the antenna cable from the unit. Remove the unit.

7. Reinstall in the reverse order. Take great care not to damage the dash trim and instrument visor. Make certain the connectors are firmly and squarely installed. If applicable, be sure to enable the SRS.

Mar 06, 2010 | 1992 Honda Accord

1 Answer

Where is the fuse for the radio in my 2005 grand vitara, i have found a fuse box but it's not in there


hi, usually the fuse for the radio is located on the back of the radio its going to be actually in the back of the radio or it will be an inline fuse running in the live wire coming from the back of the radio.

You will need to remove the radio slightly to gain access to the fuse in the back of it.

Let me know how you get on or if you need further assistance ok

Feb 01, 2010 | 2005 Suzuki Grand Vitara

Not finding what you are looking for?
2000 Hyundai Sonata Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...