Question about 1988 Chevrolet K2500

Open Question

My 1989 chevy K2500 automatic transmission will not shift,does it have a modulator or a shifting solenoid

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
lovelle40
  • 26 Answers

SOURCE: ''88 chevy K2500 won't shift past 2nd gear

Tha vacuum modulator will not keep the truck from shifting,it only helps with sift quallity.it sound like you have some internal problems and will need to take it to a transmission shop

Posted on Jan 02, 2009

Ad
  • 916 Answers

SOURCE: Hello, I own a 93

The transmission is controlled by the Transmission Control Unit (TCU).

Throttle position, rpm, and speed are input parameters to the TCU. The TCU has a default set of shift patterns. These shift patterns change over time based on your specific vehicle setup and driving habbits.

The shift patterns are only slightly affected by driving habbits over many driving cycles. But, changing the relationship between the throttle position and the actual speed being reported by the speed sensor can have an immediate effect on shift patterns.

While your speedo may now be correct, the realtionship between rpm and thottle position has not been corrected. That would take a gear change in the differentials.

The TCU can be reset to an inital learn base line. When this is done, the TCU will instantly learn the dynamics of your setup.

Any shop with an advanced ODB scan tool can reset the the TCU. The dealer or a transmission shop would be preferable.

You really should change your differential gears as opposed to resetting the TCU

This information was posted by ftgiles here

Posted on Jan 06, 2009

localwonder
  • 6784 Answers

SOURCE: Hi, I have a 1998 Chevy 3/4 ton 4x4, automatic

Yes, you are correct. i would change the filter as well. check the torque converter for stress.

Posted on Feb 28, 2009

  • 32 Answers

SOURCE: 1988 Chevy truck

no try looking at the governer on the back should be a cover about 4 in arond remove and look to see if the plastic teeth are broken or worn.

Posted on Mar 17, 2009

  • 1 Answer

SOURCE: transmission on my 2000 chevy k2500 4x4 pickup

your transmission has possibly been rebuilt with stronger springs put in. No worries. have been running mine for along while without any problems. Better this than slipping, but it is a bit annoying.

Posted on Jul 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When i put my car in park or drive it feels like it is hard to move the shifter. 2008 saturn aura


Safety system , shift lock . Has locking solenoid's that won't allow shifting from park to gear without the diver pressing on the brake pedal . Electrically controlled , brake switch , body control module .
Your best bet would be to take it to a qualified repair shop .
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock solenoid (serviced as the automatic transmission shift lock actuator), as well as the body control module (BCM) and the engine control module (ECM). The shift lock solenoid is located within the floor shift control assembly with vehicles equipped with floor shift.
• The BCM controls the voltage supply circuit of the shift lock control solenoid. The following conditions must be met before the BCM will supply voltage to the shift lock control solenoid.
The BCM controls the voltage to the shift lock control solenoid through the shift lock control solenoid controlled voltage circuit. The following conditions must be met before the BCM will supply voltage to the shift lock solenoid:

Sep 19, 2017 | Saturn Cars & Trucks

1 Answer

2005 chevy malibu damage Light front end damcodend error codes P0401 P0605 P0842 P0642 The 0401 code is being thrown twice and I belive it is the egr wich is common on these cars from what my buddy tells...


DTC P0401 Exhaust Gas Recirculation (EGR) Flow Insufficient
Probably plugged passage's , not the EGR valve .
What type code reader are you using to read these codes ? I have factory service info. Doesn't show P0842 or P0642 , no such codes . You don't show what engine yours has , I'am assuming you have 3.5 L !
P0604
Control Module Random Access Memory (RAM)
PCM
DTC P0601, P0602, P0603, P0604, P0605, P0606, P0607, P1600, P1621, P1627, P1680, P1681, P1683, or P2610 in Engine Controls - 2.2L (L61)
or
DTC P0601, P0602, P0603, P0604, P0605, P0606, P0607, P1600, P1621, P1627, P1680, P1681, P1683, or P2610 in Engine Controls - 3.5L (LX9)

P0717
Input Speed Sensor Circuit Low Voltage
PCM
DTC P0717 in Automatic Transaxle - 4T40-E/4T45-E
P0741
Torque Converter Clutch (TCC) System - Stuck Off
PCM
DTC P0741 in Automatic Transaxle - 4T40-E/4T45-E
P0742
Torque Converter Clutch (TCC) System - Stuck On
PCM
DTC P0742 in Automatic Transmission - 4T40-E/4T45-E
P0748
Pressure Control (PC) Solenoid Control Circuit
PCM
DTC P0748 in Automatic Transmission - 4T40-E/4T45-E
P0751
1-2 Shift Solenoid (SS) Valve Performance - No First or Fourth Gear
PCM
DTC P0751 in Automatic Transmission - 4T40-E/4T45-E
P0752
1-2 Shift Solenoid (SS) Valve Performance - No Second or Third Gear
PCM
DTC P0752 in Automatic Transmission - 4T40-E/4T45-E
P0753
1-2 Shift Solenoid (SS) Control Circuit
PCM
DTC P0753 in Automatic Transmission - 4T40-E/4T45-E
P0756
2-3 Shift Solenoid (SS) Valve Performance - No First or Second Gear
PCM
DTC P0756 in Automatic Transmission - 4T40-E/4T45-E
P0757
2-3 Shift Solenoid (SS) Valve Performance - No Third or Fourth Gear
PCM
DTC P0757 in Automatic Transmission - 4T40-E/4T45-E
P0758
2-3 Shift Solenoid (SS) Control Circuit
PCM
DTC P0758 in Automatic Transmission - 4T40-E/4T45-E
P0815
Upshift Switch Circuit
PCM
DTC P0815 in Automatic Transmission - 4T40-E/4T45-E
P0816
Downshift Switch Circuit
PCM
DTC P0816 in Automatic Transmission - 4T40-E/4T45-E
P0826
Up and Down Shift Switch Circuit
PCM
DTC P0826 in Automatic Transmission - 4T40-E/4T45-E
P0973
1-2 Shift Solenoid (SS) Control Circuit Low Voltage
PCM
DTC P0973 in Automatic Transmission - 4T40-E/4T45-E
P0974
1-2 Shift Solenoid (SS) Control Circuit High Voltage
PCM
DTC P0974 in Automatic Transmission - 4T40-E/4T45-E
P0976
2-3 Shift Solenoid (SS) Control Circuit Low Voltage
PCM
DTC P0976 in Automatic Transmission - 4T40-E/4T45-E
P0977
2-3 Shift Solenoid (SS) Control Circuit High Voltage
PCM
DTC P0977 in Automatic Transmission - 4T40-E/4T45-E

Sometimes with code readers they get confused an just throw any old codes . Have it checked by someone with GM Tech 2 scan tool .

Aug 03, 2017 | Chevrolet Malibu Cars & Trucks

1 Answer

2005 cts won't sift out of park, press the brake pedal and start the car, just won't shift out of park


You probably have a problem with

Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components.
• The automatic transmission shift lock control solenoid
• The brake switch
• The rear integration module (RIM)
• The transmission control module (TCM) or powertrain control module (PCM)
With the ignition ON, battery positive voltage is supplied to the automatic transmission shift lock control solenoid from the ignition 3 relay. The automatic transmission shift lock control solenoid is controlled by the rear integration module. When the rear integration module (RIM) receives a class 2 serial data message from the transmission control module (TCM) or powertrain control module (PCM) indicating that the shift lever is in the PARK position the rear integration module (RIM) grounds the automatic transmission shift lock control solenoid control circuit. This causes the solenoid to energize mechanically locking the shift lever in the PARK position. When the driver presses the brake pedal the rear integration module receives the brake applied signal and turns off the ground to the automatic transmission shift lock control solenoid control circuit. This allows the shift lever to be moved out of the PARK position.

Shift Lever Does Not Move with Brake Pedal Depressed

2
Apply the parking brake and block the wheels.
Turn ON the ignition, with the engine OFF.
Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Install a scan tool.
Turn ON the ignition, with the engine OFF.
With a scan tool, observe the TCC brake switch parameter in the transmission data display list.
Press and release the brake pedal several times.
Does the TCC brake switch status turn ON and OFF with the brake pedal?
YES - Go to Step 4
NO - Go to Stop Lamps Inoperative in Lighting Systems
4
With a scan tool, observe the brake to shift control parameter in the rear integration module data list.
Press and release the brake pedal several times.
Does the brake to shift control status turn ON and OFF with the brake pedal?
YES - Go to Step 5
NO - Go to Step 8
5
Turn OFF the ignition.
Connect a test lamp between the automatic transmission shift lock control solenoid supply voltage circuit and the automatic transmission shift lock control solenoid control circuit at the automatic transmission shift lock control solenoid.
Turn ON the ignition, with the engine OFF.
With a scan tool, command the brake to shift control ON and OFF several times while observing the test lamp.
Does the test lamp turn ON and OFF with each command?
YES - Go to Step 7
NO - Go to Step 6
6
Test the automatic transmission shift lock control solenoid control circuit for and open or short to battery voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 11
NO - Go to Step 8
7
Inspect for poor connection at the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 11
NO - Go to Step 9
8
Inspect for poor connections at the harness connector of the rear integration module (RIM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Yes - Go to Step 11
NO - Go to Step 10
9
Replace the automatic transmission shift lock control solenoid. Refer to Automatic Transmission Shift Lock Actuator Replacement .
YES - Did you complete the replacement?
NO - Go to Step 11
--
10
Replace the RIM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
YES - Did you complete the replacement?
NO - Go to Step 11
--
11
Operate the system in order to verify the repair.
Did you find and correct the condition?
YES - System OK
NO - Go to Step 2

Mar 25, 2017 | Cadillac CTS Cars & Trucks

1 Answer

Where is module on brake peddle for shifting out of park on cadilac srx4 2007


There is no module on the brake pedal . There is a brake switch , do the brake lights work ? If the brake lights work switch is ok .
Automatic Transmission Shift Lock Control Description and Operation
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock solenoid (serviced as the automatic transmission shift lock actuator), as well as the body control module (BCM) and the engine control module (ECM). The shift lock solenoid is located within the floor shift control assembly with vehicles equipped with floor shift.
• The body control module (BCM) controls the voltage supply circuit of the shift lock control solenoid. The following conditions must be before the BCM will supply voltage to the shift lock control solenoid.
The BCM controls the voltage to the shift lock control solenoid through the shift lock control solenoid controlled voltage circuit. The following conditions must be met before the BCM will supply voltage to the shift lock solenoid:
• The ignition is in the ON position.
• The engine control module (ECM) sends an input via GMLAN serial data to the BCM indicating the transmission is in the PARK position.
• The BCM determines the brake pedal is applied according the brake pedal position.
Since the shift lock control solenoid is permanently grounded, the BCM supplies voltage to the automatic transmission shift lock control solenoid, mechanically unlocking the shift lever allowing the driver to move the shift lever out of the PARK position as the solenoid energizes. When the brake pedal is not applied, the BCM turns the control voltage output of the shift lock control solenoid OFF, de-energizing the shift lock control solenoid. The de-energized solenoid mechanically locks the shift lever in the PARK position.
During remote start operation, the BCM will de-energize the shift lock control circuit, locking the shift lever in the PARK position.

Your best bet ,have it towed to a qualified repair shop !

Oct 15, 2016 | 2007 Cadillac SRX

1 Answer

2004 pontiac sunfire wont shift out of park


Problem with shift interlock system .
Automatic Transmission Shift Lock Control Description and Operation
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid


?€¢
The body control module (BCM)


?€¢
The powertrain control module (PCM)

With the ignition in the ON position, battery positive voltage is supplied to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid receives a ground from the BCM. When the automatic transmission shift lock control solenoid is energized, the shift lever mechanically locked in the PARK position. When the driver presses the brake pedal the PCM sends a class 2 serial data message to the BCM. The BCM turns OFF the ground control circuit and this de-energizes the automatic transmission shift lock control solenoid. When the automatic transmission shift lock control solenoid is de-energized, the shift lever may be moved out of the PARK position. The BCM determines transaxle shift lever position through a class 2 serial data message from the PCM. The PCM receives inputs from the park/neutral position switch and determines shift lever position. When the BCM receives this information and determines that the shift lever is out of the PARK position, the automatic transmission shift lock control solenoid ground is opened.

1

Did you perform the A Diagnostic System Check - Automatic Transmission Shift Lock Control?
Go to Step 2
Go to Diagnostic System Check - Automatic Transmission Shift Lock Control

2

  1. Turn ON the ignition, with the engine OFF.
  2. Press and hold the brake pedal.
  3. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control solenoid.
  3. Turn ON the ignition, with the engine OFF.
  4. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
YES - Go to Step 4
NO - Go to Step 5

4

Test the A/T shift lock control circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 9
NO - Go to Step 6

5

Inspect for poor connections at the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 9
Go to Step 7

6

Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 9
Go to Step 8

7

Replace the automatic transmission shift lock control solenoid. Refer to Transmission Control Replacement in Automatic Transaxle-4T40-E/4T45-E.
Did you complete the replacement?
Go to Step 9
--

8

Replace the body control module (BCM). Refer to Body Control Module Replacement in Body Control System.
Did you complete the replacement?
Go to Step 9
--

9

Operate the system in order to verify the repair.
Did you find and correct the condition?
System OK
Go to Step 2

Jun 29, 2016 | Pontiac Cars & Trucks

1 Answer

Can't shift my Chevrolet Uplander out of park.


The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid


?€¢
The body control module (BCM)


?€¢
The powertrain control module (PCM) or the transmission control module (TCM).

The BCM controls the voltage to the shift lock control solenoid through the shift lock control solenoid controlled voltage circuit. The following conditions must be met before the BCM will supply voltage to the shift lock solenoid:
?€¢
The ignition is in the ON position.


?€¢
The PCM / TCM sends an input to the BCM indicating the transmission is in the PARK position.


?€¢
The BCM determines the brake pedal is not applied according the brake pedal position.

Since the shift lock control solenoid is permanently grounded, the BCM supplies voltage to the automatic transmission shift lock control solenoid, mechanically locking the shift lever in the PARK position as the solenoid energizes. When the brake pedal is applied, the BCM turns the control voltage output of the shift lock control solenoid OFF, de-energizing the shift lock control solenoid. The de-energized solenoid releases the mechanical lock allowing the driver to move the shift lever out of the PARK position. When the transmission is out of the PARK position, the shift lock control solenoid remains de-energized.
The body control module (BCM) controls the A/T shift lock control solenoid by providing battery voltage to the A/T shift lock control solenoid. The BCM utilizes a smart driver to control the voltage supplied to the A/T shift lock control solenoid. The smart driver monitors the voltage and current flow of the control circuit.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC B2705 Gearshift Unlock Circuit
You could have a bad brake light switch , automatic transmission shift lock control solenoid.
the BCM or wiring problem
Install a scan tool. Turn ON the ignition, with the engine OFF. Press and release the brake pedal several times while observing the BTSI solenoid parameter in the body control module (BCM) output data list

Jan 17, 2016 | Chevrolet Cars & Trucks

1 Answer

2001 Pontiac Bonneville won't shift out of park


Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the ignition is ON. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid


?€¢
The automatic transmission shift lock control switch


?€¢
The brake to shift relay


?€¢
The rear integration module (RIM)

With the ignition in the ON position, battery positive voltage is supplied to the brake to shift relay coil. When the RIM energizes the brake to shift relay, the brake to shift relay switch contacts close suppling battery voltage to the automatic transmission shift lock control switch. The circuit continues through the normally --closed switch to the automatic transmission shift lock control solenoid. The permanently grounded solenoid is energized. This locks the shift linkage in the PARK position. When the driver presses the brake pedal, the contacts in the automatic transmission shift lock control switch open. This causes the automatic transmission shift lock control solenoid to release. This allows the shift lever to move from the PARK position.
Shift Lever Does Not Move with Brake Pedal Depressed ?

Jun 30, 2015 | Pontiac Cars & Trucks

1 Answer

Location of the reverse light switch on a 1989 Chevy K2500 automatic transmission


It's in the switch on the transmission that the shift linkage goes through

Mar 13, 2014 | Cars & Trucks

2 Answers

Transmission on my 2000 chevy k2500 4x4 pickup


your transmission has possibly been rebuilt with stronger springs put in. No worries. have been running mine for along while without any problems. Better this than slipping, but it is a bit annoying.

Jun 08, 2009 | 2001 Chevrolet Silverado 2500HD

3 Answers

''88 chevy K2500 won't shift past 2nd gear


Tha vacuum modulator will not keep the truck from shifting,it only helps with sift quallity.it sound like you have some internal problems and will need to take it to a transmission shop

Jan 02, 2009 | 1988 Chevrolet K2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

486 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...