Question about 1995 Cadillac Seville

2 Answers

Rear led light is out how to fix - 1995 Cadillac Seville

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 192 Answers


Contact these guys below, they will sort you out and much cheaper than a dealer.

Logan Diagnostic
209 Lighthouse Terrace
Franklin, TN 37064 USA
615. 479. 1900

Here is a link for instructions on how to remove/replace.

http://www.ledfix.com/brakelightremoval.html

Posted on Feb 27, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 306 Answers

The entire light will need replacment. the nuts that hold it in are located inside the trunklid also a quick disconnect is there for the wiring. unbolt unplug and install replacment light. that should take care of the problevem. also may want to make sure there is power at the light before replacing it. use a test light and have someone step on the brake pedal to verify voltage

Posted on Feb 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2011 Mercury Milan LED tail light out


Yes, I have a 2011 Milan as well and both sides of mine went out. One last year (2013) and the other side recently. My car is no longer under warranty and the dealer said they it would be $417 to repair. Ford needs to fix this issue because from what I have been reading it is a common problem and it is a safety issue!

Nov 05, 2012 | 2010 Mercury Milan

1 Answer

My Turn Led Signal Can Not Blink


The LED lamps are not plug-in replacements for incandescent ones because they place a much lower load on the flasher.

Mar 07, 2017 | 1994 Mercedes-Benz C-Class

1 Answer

I have a 1998 Plymouth voyager and the climate control lights are flashing. I ran a test i found on the internet and got it down to two lights flashing(the ac and the recirculate). I got it to where the...


OK got your message on the other post (About the van) I am assuming that your Voyager is equipped with Automatic Climate Control. Follow the instructions below and you will get a better idea of what is wrong with your system.

Calibration/Diagnostics
1. To enter calibration/diagnostics test, set parking brake. Start and warm engine to normal operating temperature. With engine idling, turn blower switch to high. Turn mode switch to panel. Open all outlets. Move temperature to full cold.
2. Press and hold rear wash and rear wiper buttons simultaneously for 5 seconds (Until ALL LEDs illuminate). All LEDs should illuminate for 5 seconds. Rear wiper and intermittent rear wiper button LEDs will flash alternately during calibration/diagnostics test.
3. After approximately 60 seconds, if only the rear wiper button LED is flashing, calibration is successful and the system is okay. If rear wiper and intermittent rear wiper button LEDs are flashing, Diagnostic Trouble Codes (DTCs) are present. (See "Reading Diagnostic Codes" below)
4. To exit calibration/diagnostics test at any time, press the rear window defogger button, rear wiper button, or cycle the ignition off and then on. Test will automatically terminate 15 minutes after calibration/diagnostics is entered.

Reading Diagnostic Codes
1. Perform calibration/diagnostics test. If a DTC is present after calibration/diagnostics test has been performed, system will flash rear wiper and intermittent rear wiper button LEDs in sequence. Rear wiper represents code level, and intermittent rear wiper button LED represents code value.
2. Each time the rear wash button is depressed, rear wiper button LED wil cycle to the next code level in numeric sequence. After code level 5 is reached, rear wiper button LED will cycle back to code level 1. See table below.

dttech_67.gif

May 12, 2011 | Plymouth Voyager Cars & Trucks

2 Answers

Blinking panel lights


To Calibrate , start and warm engine to normal operating temp. with engine idling turn blower switch to high, turn mode switch to panel, open all outlets, move temp lever to full cold.
press and hold rear wash and rear wiper buttons simultaneously for 5 seconds (untill all leds illuminate.) all leds should light up for 5 seconds, rear wiper and intermittent rear wiper button leds will flash alternatly during calibration... after 60 seconds if only rear wiper button led is flashing, cal. is complete

Jun 18, 2009 | 1998 Plymouth Voyager

1 Answer

Wipers


the climate control panel has come out of calibration..
to re-calibrate it you need to have
Set Blower motor ON HIGH
Set Mode position to Panel
Open all A/C outlets
Set Temperature to Cold (Both slide pots if equipped)
Depress WASH and REAR WIPER button simultaneously for 5 Seconds (Until all LED's light)

All LED's will turn on for 5 Seconds
When done REAR WIPER LED is the only LED flashing. Push Rear Wiper to exit

your a/c system must be functioning properly for it to re-calibrate.

Sep 10, 2008 | 1997 Chrysler Town & Country

4 Answers

Change rear signal bulb on 2002 ford focus wagon


Open the rear tailgate There are 2 screws that hold light housing in place.. Remove the screws then pull the housing outwards till the clip behind it springs. You then need to knock the housing sideways (outwards) to free the 2 prongs that attach housing to the car body.
Unclip the rear housing from the back of the light unit & change the bulb.

Aug 01, 2008 | 2002 Ford SVT Focus

Not finding what you are looking for?
1995 Cadillac Seville Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...