Question about Peugeot Liberte

1 Answer

My clutch on my 206 has just started to slip in 1st gear how do i ajust the clutch ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,874 Answers

Unfortunately if the clutch start to slip you can not adjust the clutch on Peugeot 206, because the clutch mechanism is automatically adjusted !!!
There is the clutch disk weared. Only replace the clutch kit, (at least the clutch disk).

Posted on Feb 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust a 1996 Mazda 121's clutch cable please?


Hi im not familer with this model,but if it is a cable the adjustment will be where the cable gose into the gearbox bellhousing,if there is not a ajuster there then it could be that the clutch pedle has a ratchet that selth ajusts as the clutch wheres down wich means im sorry to say you will need a new clutch,best of luck I hope its the first one.

Aug 08, 2015 | Mazda Cars & Trucks

1 Answer

I have a peugeot 206 allure I have clunking noise when changing from 1st to 2nd and from 2nd to 3rd but not when changing to forth or coming down the gear I have had a new gear box clutch and thrust


It could be a loose/failed engine or transmission mount. Look at the tranny rear mount and check the bolts and condition. Also check the bell housing bolts AND the bolts connecting the engine flywheel to the clutch pressure plate.

Jul 23, 2014 | 2003 Peugeot 206

1 Answer

Problems selecting 1st gear peugeot 106 1.1 zest


If the clutch is a problem you will have difficulty selecting 1st only as the gears would be spinning from the engine revs.. I would say that the front input shaft (clutch shaft) bearing is failing allowing miss alignment of the synchros and not allowing proper engagement of the gears synchro rings. It means removal and repair to the gear box so the clutch can be inspected while the box is out.

Apr 08, 2013 | Cars & Trucks

1 Answer

Clutch starting to slip 1994 camaro can i adjust it


It does sound like your clutch needs replacing. Adjusting the clutch may help but will not solve the problem. If the transmission has not been serviced for a long time it is a good idea to replace the transmission fluid, inspect the pressure plate. They may also start to wear.

Feb 05, 2012 | 1994 Chevrolet Camaro

1 Answer

Peugeot 206 NEW clutch pressure and clutch plates were replaced including the bearing. Clutch is making a rattling noise but not when pedal is down. Having difficulty getting into 1st and 2nd gears....


its likley to be the clutch center plate cush springs are loos and the center plate is warped so wnen you try to get into gear the clutch is draging the gear box around,,,bipping the clutch stops the clutch spinning so no noise! all you can do is strip the lot down again and fine the fault and fix it

Feb 08, 2010 | 1987 Peugeot Liberte

1 Answer

Feels like my manual five speed slips in fifth gear going less than 70


Your clutch plate is probably worn.
You could try to ajust the clutch pressure plate to compensate for this (consult repair manual or get a mechanic to do it for you: should be relatively cheap and fast!) but it could be worned beyond ajustment range and would need replacing.

Dec 25, 2009 | 2001 Ford Mustang

1 Answer

After traveling about 8km my car wont go into 1st or reverse gear. when it is cold it goes into all the gears fine. when i switch the car off it will go into gear. we did put a new(aftermarket clutch) in a...


Cluth cable ajustment if equiped.Some cars have a cluth cylender if your model has the cylender no ajustment is available.If you had your cluth changed at a garage you might consider takeing it back in for ajustments.If you changed the clutch check cluth cable for ajustment if your car is equiped with cable if not i would perhaps remove the transmission and inspect clutch for loose clutch plate or release bearing might not be seated properly hope this helped you.

Dec 24, 2009 | Mazda 323 Cars & Trucks

2 Answers

Slips out of 1st and 5th


Have you checked your transmission fluid level and your transmission filter? That's a common cause of slippping.

Sep 27, 2009 | 1996 Toyota Tacoma

1 Answer

Lost gears


I have the same problem with my 2001 volkswagen cabrio, but I know the solution.
You need a new clutch, or it will continue to slip.
If you cannot afford the clutch. You can "baby" the clutch by easing the clutch out, and eventually it will catch. (It should catch in a second or two.)

May 17, 2009 | 2000 Volkswagen Jetta TDI

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

316 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...