Question about 1996 Ford Ranger SuperCab
It should be under the hood on the driverside fender well and heres a picture to help you locate it.
Posted on Feb 08, 2010
It should be on the bottom of steering column,,inside truck,,should be a metal rod connected to it,,
Posted on Feb 08, 2010
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
It does not have an ignition control module.
The electronic ignition (EI) for the 4.0L engine consists of the following components:
Crankshaft position sensor (CKP sensor) and 36 minus 1 tooth trigger wheel.
Ignition coil .
powertrain control module (PCM) .
The PCM controls the firing of the coil based on the signal from the crankshaft position sensor.
The crankshaft position sensor (CKP sensor) is a variable reluctance-type sensor, triggered by a 36 minus 1 tooth trigger wheel configuration machined into the rear of the crankshaft vibration damper. The signal generated by this CKP sensor is called a CKP signal. The CKP signal provides the base timing and rpm information to the powertrain control module (PCM). Base timing is set at 10 degrees BTDC and is not adjustable.
If vehicle has no spark then turn key to on position,check engine light should come on.As you start cranking engine it should go out while cranking after about 10 secs. it should come back on(while cranking). If it come on then the PCM sees the signal,if it does not then PCM is not seeing it and this is your problem,either the CKP sensor or the wiring to it.
Posted on Mar 16, 2009
It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.
Posted on Apr 08, 2009
tragik nc: In looking this car up in both the 4 and 6 cyl configurations, Ford said that the ignition control module is no longer a separate component. It is actually integrated into the PCM (power control module)
This is located in the right rear corner of the engine compartment behind the power steering reservoir.
Good Luck, mybunkey>>>>>>>>>>>>>>>>>
Posted on Apr 20, 2009
SOURCE: Ford Ranger will not start
Does the car click when you turn the ignition? If it does, it is probably your starter. If the engine does not turn when you turn the ignition.
Posted on Sep 30, 2009
For 1993 Ford Truck Ranger 4WD 3.0L MFI 6cyl the Control Module-Ignition is located under hood, center, rear engine area, mounted on distributor.
Fig. 1: View of the remote mounted Ignition Control Module (ICM)
Hope this help (remember comment and rated this).
Posted on Jul 27, 2010
Tips for a great answer:
Jan 16, 2017 | Ford Ranger Cars & Trucks
Feb 19, 2012 | 1992 Ford Ranger
Sep 03, 2011 | Ford Ranger Cars & Trucks
Jan 09, 2011 | 1996 Ford Ranger SuperCab
Jan 06, 2011 | 1996 Ford Ranger SuperCab
Jul 27, 2010 | 1993 Ford Ranger SuperCab
Dec 11, 2009 | 1998 Ford Ranger SuperCab
Nov 07, 2009 | 1996 Ford Ranger SuperCab
May 03, 2009 | 1996 Ford Ranger SuperCab
Apr 08, 2009 | 1996 Ford Ranger SuperCab
2,184 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: