Question about 2002 Dodge Neon

Open Question

The windshield washer pump hoses that connect behind the fiberglass panel on the hood have become disconnected on my dodge neon sx20. Where can I find pictures and instructions on how to reconnect?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 599 Answers

SOURCE: Windshield wiper spray hose disconnected

razor blade ...carefully.......... 3m weatherstripping adhesive (gorilla snot) to re secure....good luck

Posted on Jan 13, 2009

freetek
  • 5568 Answers

SOURCE: 2002 Dodge Caravan Windshield Washer

If the pump still makes noise, you may just have clogged nozzles, have you tried those yet? Also, if you have windshield cleaner left over from summer, it may have frozen in the lines. 

Posted on Jan 26, 2009

  • 1071 Answers

SOURCE: Front Washer fluid not spraying in 1999 Dodge Caravan Sport

front pump motor may have come out of washer bottle it is only held in by the seal no bolts

Posted on Jul 27, 2009

localwonder
  • 6784 Answers

SOURCE: 2002 Dodge Neon Fuel Pump Replacement

HI.Your fuel pump is an integrated part of the pump module, which also contains the fuel reservoir, level sensor, inlet strainer and fuel pressure regulator. The inlet strainer, fuel pressure regulator and level sensor are the only serviceable items. If the fuel pump requires service, replace the entire fuel pump module.

There is no access panel. You will need to, slightly, drop the fuel tank, in order to extract the module for replacement. This module it mounted on-top of the tank. the module is inserted into the tank.

Posted on Dec 21, 2009

ZJLimited
  • 17970 Answers

SOURCE: where is the fuse for window washer pump in 2000

Check in the Fuse Block (position 4) for Wiper and Washer Pump...

4020d8b.jpg

Visit this link to access at Section-26-Wiring-Diagrams-EPL-8W

Hope helps.

Posted on Jun 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer hose


How do you know the hose came off? These hoses don't normally become disconnected

May 22, 2015 | 2001 Ford Windstar

1 Answer

Where is the windshield washer motor located? Is it near the heater motor? I had mine fixed and now the heat comes out of the dash for the defroster


Windshield Washer Pump Removal & Installation To Remove:
  1. Remove the air cleaner assembly.
  2. Remove the bolts. windwash.gif

  3. Position the pump and reservoir aside.
  4. Disconnect the electrical connectors.
  5. Disconnect the washer hose.
  6. Remove the pump and reservoir.
  7. Remove the washer pump.
washpump.gif

WARNING
Windshield washer solution contains methanol which is poisonous. Observe all cautions and warnings indicated on label of washer solution container.
NOTE: Windshield washer fluid should be collected in a container after the windshield washer hose is disconnected.
To Install:
WARNING
Windshield washer solution contains methanol which is poisonous. Observe all cautions and warnings indicated on label of washer solution container.
  1. Install washer pump in reservoir.
  2. Install washer pump reservoir assembly.
  3. Connect washer hose.
  4. Connect washer electrical connector.
  5. Install air cleaner assembly.
---
The windshield wiper fluid pump is located in the tank which is not in the heater motor or defroster area in the dash.

The defroster/heat control door is located in the dash board area:

Air Door Actuators, Cables or Motors Removal & Installation Air Inlet Door Vacuum Control Motor To Remove:
  1. Remove the instrument panel lower insulator cover.
  2. Disconnect the vacuum connector.
  3. Remove the control arm clip and the spring.
  4. Remove the nuts and the air inlet door vacuum control motor.
Air inlet door vacuum motor mounting screws for-10-00-245.gif

To Install:
  1. Install the vacuum motor on the mounting bracket.
  2. Connect the control arm and spring.
  3. Connect the vacuum hose to the vacuum motor.
  4. Install the lower instrument panel lower cover.
Floor Defrost Door Vacuum Control Motor To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the left lower dash insulator panel and disconnect the lamp.
  3. Remove the two pin-type retainers and remove the fill panel.
  4. Remove the DLC mounting screws.
  5. Detach the vacuum line.
  6. Remove the lighting module.
  7. Remove the screws and the bracket.
  8. Remove the floor/defrost door vacuum control motor.
Floor/Defrost vacuum motor mounting screws for-10-00-246.gif

To Install:
  1. Connect the vacuum lines and install the floor/defrost vacuum motor.
  2. Install the bracket and lighting control module.
  3. Install the DLC bracket and mounting screws.
  4. Install the fill panel.
  5. Install the left lower dash insulator panel.
  6. Connect the negative battery cable.
Panel Door Vacuum Control Motor To Remove:
  1. Remove the instrument panel.
  2. Reach through the door opening and remove the pin.
  3. Disconnect the panel door vacuum control motor vacuum line.
  4. Remove the screws and remove the panel door vacuum control motor.
To Install:
  1. Install the panel door vacuum motor.
  2. Connect the vacuum line to the panel door motor.
  3. Reach through the opening and install the pin to the linkage.
  4. Install the instrument panel.
prev.gif next.gif

Jan 19, 2011 | 2003 Mercury Grand Marquis

2 Answers

The windshield washer for both the front and back doesn't dispense fluid. The pump motor seems to be working. I tried tracing the line to see if it had become disconnected, but i couldn't follow it all the...


try and fill up the washer bottle with water for test and use it. if you hear the pump work keep using it till you see where fluid is leaking out. my guess is a hose is broken and all the fluid is leaking out

Dec 16, 2010 | Jeep Liberty Cars & Trucks

1 Answer

Windshield washer fluid hose has become disconnected


open the hood on the car and you will see the hose has come off on the hood to the washer jets. recconnect it and put a little duct tape around the plastic connector to keep it from comming apart again.

Nov 30, 2010 | 2002 Jaguar X-Type

2 Answers

Where is the windshield washer motor?


it is connected to the bottom of the windshield washer reservoir... under the hood.

Sep 29, 2010 | 1997 Toyota Celica

2 Answers

How do I fix my window washer pump on my 2000 dodge caravan?


One can get a repair kit that includes a new motor pump and wiring clips, or

one can get the original motor that plugs into the windshield wiper fluid reservoir.

---
Windshield wiper reservoir (gives idea of how to change the windshield wiper fluid pump motor) Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the right front wheel and splash shield.
  4. Disconnect the electrical connectors from the pumps and detach the rear washer hose.
  5. Place a drain pan under the reservoir if it contains fluid.
  6. Disconnect the front washer hose at the wiper unit in the engine compartment. NOTE: The front hose will be removed with the reservoir.
  7. Let the fluid drain from the reservoir.
  8. Remove the mounting screws and the reservoir.
To Install:
  1. Install the fluid reservoir with the mounting screws.
  2. Connect the front washer hose in the engine compartment.
  3. Connect the electrical connectors and rear washer hose.
  4. Install the splash shield.
  5. Install the right front wheel.
  6. Lower the vehicle.
prev.gif next.gif

Aug 27, 2010 | 2000 Dodge Caravan

1 Answer

Mercury villager 1994 washer pump not working


the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal
  1. Disconnect the battery ground cable (14301).
  2. Raise and support the vehicle.
  3. Remove the RH wheel (1007).
  4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
  5. Remove the windshield washer reservoir top bolt.

  6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
  7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
  8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
  9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
  10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.

    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.

  11. Loosen the two windshield washer reservoir side bolts.
  12. Remove the windshield washer reservoir by sliding it out of the side slots.
  13. Remove the windshield washer pump.

    Installation
To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

Sep 09, 2009 | 1994 Mercury Villager

1 Answer

Wash wipe on a Focus 2000 model


I blieve it's the same pump taht runs the rear and front washers.

The windshield washer comprises the following parts:
  • Windshield washer reservoir, below the front left-hand fender
  • Washer pump, on the outside of the washer reservoir
  • Two washer nozzles on the hood/bonnet, adjustable.
---------------------------------------------------------
Windshield Washer Pump and Reservoir Removal
All vehicles
  1. Remove the windshield washer reservoir filler neck.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the right-hand fender splash shield (wheel shown removed for clarity).
  1. Remove the washer reservoir.
    • Disconnect the electrical connectors.
    • Pull off the hoses.
  1. Remove the windshield washer pump with rubber gasket (shown with reservoir installed).
    1. Disconnect the electrical connector.
    1. Disconnect the hoses.
    1. Lift out the pump.

Feb 27, 2009 | 2000 Ford Focus

1 Answer

Windshield washer fluid hose disconnected


Yoou can pick up the hose and more connection fittings at orielly's, route along fire wall and fender (keep away from heat of engine)

Feb 12, 2009 | 1996 Honda Accord

1 Answer

2001 Buick Regal LS windshield washer fluid does not spray


There are a number of different issues that could cause this.

-The circuit for the wiper should be the same as the washer; same fuse. -I'd suggest trying to run the washer while the hood is open and the engine off. If it runs, you should hear a dull whine.(a 2nd person might be of use to help look and listen)...(find the pump by following the hoses from the wipers to a unit mounted close to the dashboard in the engine compartment)
-If it runs, check to see if any fluid is coming from a hose that might have become disconnected.
-If the pump runs, and if you see no fluid coming from anywhere, and if you can reach the hose connected to the washer pump, pull that hose off the pump. Try running the pump again to see if anything comes out in a good stream.
-If the pump doesn't run at all, check to make sure the connector hasn't come loose.
-If the pump still doesn't run, check to see if you have 12 volts at the connector at the pump. A simple check can be done with an auto bulb connected to the plug at the motor while the pump switch is pushed.
-If you have power at that point, you likely need to replace the pump and motor.(depending upon the age of vehicle & your mechanical abilities...a call to a local wrecking yard is suggested ..atleast to compare the cost vs. new)

hope that helps

Oct 07, 2008 | 2001 Buick Regal

Not finding what you are looking for?
2002 Dodge Neon Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...