Question about 2002 Chrysler Voyager

1 Answer

Engine light comes on codes say tcm ,possible open or short,transaxle solinoid or bad tcm.Shifts fine when first started once I stop and turn off engine and don't let it cool down it will not shift properly only goes to gear3 .If I let it cool down it shifts properly.

Posted by on

  • 3 more comments 
  • reyvan2 Feb 08, 2010

    codes were printed out at autozone. oem number to cross:P0700.transaxle control system fault. ecm received a signal that the transaxle control module has a fault.probable cause aa1shorted or open circuit within the transaxle.aa2failure of transaxle control module.P0605 tcm rom fault.ecm detected a rom self test failure within transmission .probable cause.aa1 shorted solenoid or sensor within transmission. aa2shorted electrical circuit.aa3 failed tcm

  • reyvan2 Feb 08, 2010

    P0700

  • reyvan2 Feb 08, 2010

    P0700,p0605

  • reyvan2 Feb 09, 2010

    I was told Ineed to bring the the vehicle to dealer to reset or program module when I replace it with one from another vehicle.

  • reyvan2 Feb 09, 2010

    i was told if i buy a used tcm ihave to bring it to dealer to get it programed

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 146 Answers

What is the exact code your getting? Thanks

Posted on Feb 08, 2010

  • 1 more comment 
  • edwin187 Feb 08, 2010

    Ok, this means your transmission control module has failed and needs to be replaced. You can get a used one from www.car-parts.com sort by price and have them ship it to you to save money. Let me know if you have questions, thanks.

  • edwin187 Feb 08, 2010

    Ok, replace Transmission Control Module and problem will be fixed. Thanks

  • edwin187 Feb 09, 2010

    That is true, but you are still saving alot of money. If you want to buy it new its up to you but this is definitly the problem.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the probable causes of DTCs P1603, P1604, and P1605?


OBD-II code P1603 indicates an issue with TCU communication.
There are communications that exist between the engine control module, or ECM, and the transaxle control module, or TCM. This communication is done through a control area network, or CAN. With the communication of the CAN, an independent pin and wiring is needed to receive a signal that includes sensor information from the ECM. The more information there is to communicate, the more wiring that is needed. When it comes to CAN communication, all of the information communicated is done alone control modules like the ECM and TCM using CAN lines. When there is a problem with these lines, the ECM will detect the problem and store a P1603 trouble code; the storing of the trouble code is what causes the SES or check engine light to illuminate on the dash.
Possible causes of trouble code P1603 include:
  • Faulty transaxle control module (TCM)
  • Faulty engine control module (ECM)
  • Harness running from the TCM to the ECM has a short
  • There is a poor electrical connection between the TCM and ECM
Diagnosing the exact cause of the problem should always begin with a visual inspection that could reveal bad wiring, loose connections, or damaged parts. From there, it is a matter of running down the list to determine what needs to be replaced. In general, a bad ECM will cause a loss of power, poor fuel economy, and stalling engine. While a bad TCM will have more prevalent transaxle issues like erratic shifting
P1605 and P1605
These codes are indicating a starting problem and rough idling. Code p1604 is a very vague code and diagnosing it without having a symptom is very complicated. And code p1605 is rough idling which means that the computer have noticed a rough idle situation usually this code is accompanied by other codes or if it's alone then I would suspect a fuel pressure issue. These two codes involve diagnosis and we'll need to dig into this problem deeper to find out what's causing them, Unless you are an experienced technician who need assistance then I will suggest that you take your vehicle to your local toyota dealership and they should be able to find the problem.
P1P

Feb 12, 2016 | 2011 Toyota Sienna

1 Answer

I have grand cherokee 2001 limited the code p0700 is apper the gear is started scend shift espically in morinig


possible causes
Shorted or open circuit within Transmission Control Module (TCM)
- Faulty Transmission Control Module (TCM)
symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Driveability problems
- Transmission shifting problems
p0700 description
The transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. When the TCM detects a malfunction with the control, a signal is send to the Engine Control Module (ECM) to trigger the Engine Light or Service Engine Soon light. The ECM stores the P0700 code and it means the TCM detected a malfunction with the transaxle controls.

Read more: http://engine-codes.com/p0700_jeep.html#ixzz2hihK6PVo

Oct 14, 2013 | 2001 Jeep Grand Cherokee

2 Answers

Codes P1782, P0755, and P0700


P1782 DODGE - 2/4-OD Pressure Switch Circuitxicon.jpghttp://engine-codes.com/p1782_dodge.htmlForum CodePossible causes- Low transmission fluid level
- Dirty transmission fluid
- Faulty 2/4-OD Pressure Switch
- 2/4-OD Pressure switch poor electrical connection
- 2/4-OD Pressure switch circuit is open or shorted
Symptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Transmission shift shockP1782 DODGE Description The pressure 2/4-OD Pressure Switch is part of the pressure switch of the transmission. The pressure switch are located in the solenoid assembly. The switch provide input information to the Transmission Control Module (TCM). The switch will inform to the TCM is pressure exist in a specified hydraulic circuit. the TCM uses this information to verified that the solenoids are working or not.
P0755 DODGE - 2/4 Solenoid Circuitxicon.jpghttp://engine-codes.com/p0755_dodge.htmlForum CodePossible causes- Low transmission fluid level
- Dirty transmission fluid
- Faulty 2/4 solenoid valve
- 2/4 solenoid valve harness is open or shorted
- 2/4 solenoid valve circuit poor electrical connection
P0700 DODGE - Transaxle Control System Malfunctionxicon.jpghttp://engine-codes.com/p0700_dodge.htmlForum CodePossible causes- Shorted or open circuit within transmission control module (TCM)
- Failure of transaxle control module Tech notes Since the P0700 is just and informative code, check the TCM for more codes to resolve the problem.
Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Driveability problems
- Transaxle shifting problems

Jul 26, 2012 | Plymouth Breeze Cars & Trucks

2 Answers

I have a 2011 dodge caliber and it isz throw a c0700 code could u tell me what this is


P0700 DODGE - Transaxle Control System Malfunction

Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Driveability problems
- Transaxle shifting problems

Possible causes - Shorted or open circuit within transmission control module (TCM)
- Failure of transaxle control module

Tech notes Since the P0700 is just and informative code, check the TCM for more codes to resolve the problem.

P0700 DODGE Description The transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. When the TCM detects a malfunction with the control, a signal is send to the Engine Control Module (ECM) to trigger the Engine Light or Service Engine Soon light. The ECM stores the P0700 code and it means the TCM detected a malfunction with the transaxle controls.
CLEAR THE CODES AND SEE IF IT RESETS. MOST LIKELY NOT A PROBLEM

Sep 07, 2011 | 2002 Dodge Grand Caravan

1 Answer

I have a 2000 derango with a 4.7 and my trans shifts funny. It shifts from first to third, bypassing second. When put into second it will be in second but won't go to first manually. Overdrive saloon...


P0700 Information Code The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. You will need to have your TCM code scanned to figure out what the problem is. Most likely it's a bad solenoid in the transmission. Most automotive shops have the TCM scanner.

Aug 23, 2011 | 2000 Dodge Durango

1 Answer

My 2009 Hyundai Sonata quit accelerating while driving in town. The ESC and check engine light came on. I was able to turn the car off and back on and the ESC light went off and acceleration worked...


This may not be your problem but it does bring the vehicle in fail safe you may have a warranty
Group TRANSAXLE
Number 09-AT-016
Date AUGUST, 2009
Model
1999-SONATA
2001-ELANTRA, SANTA FE & XG
2003-TIBURON
2005-TUCSON
2006-AZERA
2007-ENTOURAGE

Subject
AUTOMATIC TRANSAXLE DIAGNOSTIC TROUBLE CODES P0715, P0716, P0717, P0720, P0721 & P0722

An improperly functioning input speed sensor or output speed sensor may result in the following conditions:
^ "Check Engine" light on
^ Harsh P-R or P-D engagement shock
^ Transaxle in 3rd gear fail-safe
^ Diagnostic trouble codes 1. Using a GDS, check for DTCs in both the "Engine" and "Automatic Transaxle" menus. Record the DTC and description.
2. From the GDS, select:
^ Vehicle
^ "Auto Transaxle" menu
^ "Current Data"
^ "Input speed sensor" and "output speed sensor". Drive the vehicle and monitor the input and output speed sensors. If the sensors show:
^ Continuous output, the wiring currently has no open/shorts. Go to Step 6.
^ No output, go to Step 3
3. Check the wiring harness visually for an open circuit or short circuit to ground. Check for a pinched harness at the PCM/TCM attachment bolts.
4. Disconnect the connectors at the input and output speed sensor and PCM/TCM. Check for bent pins or pins not fully inserted into the connector.
5. If a harness open/short is found, repair or replace the ECM control harness between the PCM/TCM and transaxle and go to Step 8. If not, go to Step 6.

Aug 22, 2011 | Hyundai Sonata Cars & Trucks

3 Answers

Car does not run ,I check the code ,it is P0700


Because it is not starting, you should replace the Crankshaft sensor (above the oil filter, back of the engine)-it will cause a P0700-I have a 99 SL2, 178,000 miles


DTC) CODE # P0700....Transmission Control System (MIL Request)
Translation: Transmission Control Module (TCM) Malfunction or Failure. P0700 Information Code The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM. This code is for information ONLY. If this code is present, check for transaxle codes. So basically, the P0700 code is telling you to check the TCM for a transaxle DTC. The TCM can not turn on the check engine light so it has the PCM do it. The dealer probably saw the code P0700 and went to the TCM and pulled out the code stored there telling them the Transmission Solenoid Assembly (TSA) is bad. This is a good example of understanding what the codes actually mean. If the manual you looked at said the TCM is bad and to replace the TCM when you see a P0700, then it is wrong.

Jan 24, 2011 | Saturn Ion Cars & Trucks

2 Answers

Error P0700. What is the cause? How to repair it?


P0700 JEEP - Transaxle Control System Malfunction
The transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. When the TCM detects a malfunction with the control, a signal is send to the Engine Control Module (ECM) to trigger the Engine Light or Service Engine Soon light. The ECM stores the P0700 code and it means the TCM detected a malfunction with the transaxle controls.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Driveability problems
- Transaxle shifting problems

Possible causes
- Shorted or open circuit within transmission control module (TCM)
- Failure of transaxle control module

Tech notes: Since the P0700 is just and informative code, check the TCM for more codes to resolve the problem. So you'll have to have the dealer or another qualified shop/technician pull the transaxle codes from the TCM and go from there.

Good luck (remember to rate this answer)

Jan 17, 2011 | 2004 Jeep Grand Cherokee

2 Answers

Trans range sensor circuit malfunction


Transaxle Range Sensor Circuit Malfunction (PRNDL Input).  

Check for: _ Possibly a connector near the shift lever has come loose/dirty contacts, or there is a broken wire from it somewhere going to the TCM 
- Corroded or faulty Range Switch. - Open between Meter Fuse and Range Switch (C136-4).
- Open between Range Switch (C136) and TCM (C229) on one or more circuits. 
- Short to Battery between Range Switch (C136) and TCM (C229) on one or more circuits. 
- Short between two or more wires between Range Switch (C136) and TCM (C229). 

If Meter Fuse is blown, repair any shorts in the Meter Fuse circuit.

P1624 MIL Request Signal from TCM to ECM.This is only a request from TCM to ECM to turn the MIL on. The fault code is stored in the TCM.The Freeze Frame Data is stored in the ECM under the P1624 request code. Be sure to retrieve freeze frame data before clearing code P1624 from ECM. 
TCM = Transmission control module 
ECM = Engine control module (or more commonly known as ECU) 
MIL = Malfunction indicator light (more commonly "check engine light" or CEL) 

Good luck and hope this helps

May 05, 2009 | 2003 Kia Spectra

Not finding what you are looking for?
2002 Chrysler Voyager Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...